converted Wurkkos TS25 build...

... and gave it a smoother ramp
... and the other new functions added recently

4 files changed, 273 insertions, 150 deletions

diff --git a/hwdef-Wurkkos_TS25.h b/hwdef-Wurkkos_TS25.h
deleted file mode 100644
index cf34754..0000000
--- a/hwdef-Wurkkos_TS25.h
+++ /dev/null
@@ -1,116 +0,0 @@
-// Wurkkos TS25 driver layout
-// Copyright (C) 2022-2023 (FIXME)
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * Driver pinout:
- * eSwitch:    PA5
- * PWM FET:    PB0 (TCA0 WO0)
- * PWM 1x7135: PB1 (TCA0 WO1)
- * Voltage:    VCC
- * Aux Blue:   PC1
- * Aux Red:    PC2
- * Aux Green:  PC3
- */
-
-#define LAYOUT_DEFINED
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define PWM_CHANNELS 2
-#define PWM_BITS 16
-#define PWM_TOP 255
-#define USE_DYN_PWM
-
-#ifndef SWITCH_PIN
-#define SWITCH_PIN     PIN5_bp
-#define SWITCH_PORT    VPORTA.IN
-#define SWITCH_ISC_REG PORTA.PIN2CTRL
-#define SWITCH_VECT    PORTA_PORT_vect
-#define SWITCH_INTFLG  VPORTA.INTFLAGS
-#endif
-
-
-// 7135 channel
-#ifndef PWM1_PIN
-#define PWM1_PIN PB1               //
-#define PWM1_LVL TCA0.SINGLE.CMP1BUF  // CMP1 is the output compare register for PB1
-#endif
-
-// FET channel
-#ifndef PWM2_PIN
-#define PWM2_PIN PB0               //
-#define PWM2_LVL TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
-#endif
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM1_TOP TCA0.SINGLE.PERBUF   // holds the TOP value for for variable-resolution PWM
-// not necessary when double-buffered "BUF" registers are used
-#define PWM1_CNT TCA0.SINGLE.CNT   // for resetting phase after each TOP adjustment
-#define PWM1_PHASE_RESET_OFF  // force reset while shutting off
-#define PWM1_PHASE_RESET_ON   // force reset while turning on
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-
-// this driver allows for aux LEDs under the optic
-#define AUXLED_B_PIN    PIN1_bp    // pin 1
-#define AUXLED_R_PIN    PIN2_bp    // pin 2
-#define AUXLED_G_PIN    PIN3_bp    // pin 3
-#define AUXLED_RGB_PORT PORTC  // PORTA or PORTB or PORTC
-
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
-
-    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
-
-    //VPORTA.DIR = ...;
-    VPORTB.DIR = PIN0_bm | PIN1_bm;  // Outputs: PWMs
-    VPORTC.DIR = PIN1_bm | PIN2_bm | PIN3_bm;
-
-    // enable pullups on the unused pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
-    PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN5CTRL = PORT_PULLUPEN_bm;
-
-    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
-    //PORTC.PIN1CTRL = PORT_PULLUPEN_bm; // RGB Aux
-    //PORTC.PIN2CTRL = PORT_PULLUPEN_bm; // RGB Aux
-    //PORTC.PIN3CTRL = PORT_PULLUPEN_bm; // RGB Aux
-
-    // set up the PWM
-    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
-    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
-    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
-    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
-    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
-    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
-    // See the manual for other pins, clocks, configs, portmux, etc
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
-    PWM1_TOP = PWM_TOP;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
-}
-
diff --git a/hwdef-wurkkos-ts25.c b/hwdef-wurkkos-ts25.c
new file mode 100644
index 0000000..1d5b656
--- /dev/null
+++ b/hwdef-wurkkos-ts25.c
@@ -0,0 +1,49 @@
+// Wurkkos TS25 PWM helper functions
+// Copyright (C) 2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+
+#pragma once
+
+#include "chan-rgbaux.c"
+
+// single set of LEDs with 2 stacked power channels, DDFET+1 or DDFET+linear
+void set_level_main(uint8_t level) {
+    if (level == 0) {
+        CH1_PWM = 0;
+        CH2_PWM = 0;
+        PWM_CNT = 0;  // reset phase
+        return;
+    }
+
+    level --;  // PWM array index = level - 1
+    PWM_DATATYPE ch1_pwm = PWM_GET(pwm1_levels, level);
+    PWM_DATATYPE ch2_pwm = PWM_GET(pwm2_levels, level);
+    // pulse frequency modulation, a.k.a. dynamic PWM
+    uint16_t top = PWM_GET16(pwm_tops, level);
+
+    CH1_PWM = ch1_pwm;
+    CH2_PWM = ch2_pwm;
+    // wait to sync the counter and avoid flashes
+    // (unnecessary w/ buffered registers)
+    //while(actual_level && (PWM_CNT > (top - 32))) {}
+    PWM_TOP = top;
+    // force reset phase when turning on from zero
+    // (because otherwise the initial response is inconsistent)
+    if (! actual_level) PWM_CNT = 0;
+}
+
+bool gradual_tick_main(uint8_t gt) {
+    PWM_DATATYPE pwm1 = PWM_GET(pwm1_levels, gt);
+    PWM_DATATYPE pwm2 = PWM_GET(pwm2_levels, gt);
+
+    GRADUAL_ADJUST_STACKED(pwm1, CH1_PWM, PWM_TOP_INIT);
+    GRADUAL_ADJUST_SIMPLE (pwm2, CH2_PWM);
+
+    if (   (pwm1 == CH1_PWM)
+        && (pwm2 == CH2_PWM)
+       ) {
+        return true;  // done
+    }
+    return false;  // not done yet
+}
+
diff --git a/hwdef-wurkkos-ts25.h b/hwdef-wurkkos-ts25.h
new file mode 100644
index 0000000..b9fbdfb
--- /dev/null
+++ b/hwdef-wurkkos-ts25.h
@@ -0,0 +1,179 @@
+// Wurkkos TS25 driver layout
+// Copyright (C) 2022-2023 (FIXME)
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/*
+ * Driver pinout:
+ * eSwitch:    PA5
+ * PWM FET:    PB0 (TCA0 WO0)
+ * PWM 1x7135: PB1 (TCA0 WO1)
+ * Voltage:    VCC
+ * Aux Red:    PC2
+ * Aux Green:  PC3
+ * Aux Blue:   PC1
+ */
+
+#define ATTINY 1616
+#include <avr/io.h>
+
+#define HWDEF_C_FILE hwdef-wurkkos-ts25.c
+
+// allow using aux LEDs as extra channel modes
+#include "chan-rgbaux.h"
+
+#define USE_CHANNEL_MODES
+// channel modes:
+// * 0. FET+7135 stacked
+// * 1. aux red
+// * 2. aux yellow
+// * 3. aux green
+// * 4. aux cyan
+// * 5. aux blue
+// * 6. aux purple
+// * 7. aux white
+#define NUM_CHANNEL_MODES  8
+enum CHANNEL_MODES {
+    CM_MAIN = 0,
+    CM_AUXRED,
+    CM_AUXYEL,
+    CM_AUXGRN,
+    CM_AUXCYN,
+    CM_AUXBLU,
+    CM_AUXPRP,
+    CM_AUXWHT,
+};
+
+#define DEFAULT_CHANNEL_MODE  CM_MAIN
+
+#define CHANNEL_MODES_ENABLED 0b00000001
+#define CHANNEL_HAS_ARGS      0b00000000
+
+#define SET_LEVEL_MODES      set_level_main, \
+                             set_level_auxred, \
+                             set_level_auxyel, \
+                             set_level_auxgrn, \
+                             set_level_auxcyn, \
+                             set_level_auxblu, \
+                             set_level_auxprp, \
+                             set_level_auxwht
+// gradual ticking for thermal regulation
+#define GRADUAL_TICK_MODES   gradual_tick_main, \
+                             gradual_tick_null, \
+                             gradual_tick_null, \
+                             gradual_tick_null, \
+                             gradual_tick_null, \
+                             gradual_tick_null, \
+                             gradual_tick_null, \
+                             gradual_tick_null
+
+
+#define PWM_CHANNELS 2  // old, remove this
+
+#define PWM_BITS      16        // dynamic 16-bit, but never goes over 255
+#define PWM_GET       PWM_GET8
+#define PWM_DATATYPE  uint16_t  // is used for PWM_TOPS (which goes way over 255)
+#define PWM_DATATYPE2 uint16_t  // only needs 32-bit if ramp values go over 255
+#define PWM1_DATATYPE uint8_t   // 1x7135 ramp
+#define PWM2_DATATYPE uint8_t   // DD FET ramp
+
+// PWM parameters of both channels are tied together because they share a counter
+#define PWM_TOP TCA0.SINGLE.PERBUF   // holds the TOP value for for variable-resolution PWM
+#define PWM_TOP_INIT  255    // highest value used in top half of ramp
+// not necessary when double-buffered "BUF" registers are used
+#define PWM_CNT TCA0.SINGLE.CNT   // for resetting phase after each TOP adjustment
+
+// 1x7135 channel
+#define CH1_PIN  PB1
+#define CH1_PWM  TCA0.SINGLE.CMP1BUF  // CMP1 is the output compare register for PB1
+
+// DD FET channel
+#define CH2_PIN  PB0
+#define CH2_PWM  TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
+
+// e-switch
+#define SWITCH_PIN      PIN5_bp
+//#define SWITCH_PCINT    PCINT0
+#define SWITCH_PORT     VPORTA.IN
+#define SWITCH_ISC_REG  PORTA.PIN2CTRL
+#define SWITCH_VECT     PORTA_PORT_vect
+#define SWITCH_INTFLG   VPORTA.INTFLAGS
+//#define PCINT_vect      PCINT0_vect
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
+#endif
+
+// this driver allows for aux LEDs under the optic
+#define AUXLED_R_PIN    PIN2_bp    // pin 2
+#define AUXLED_G_PIN    PIN3_bp    // pin 3
+#define AUXLED_B_PIN    PIN1_bp    // pin 1
+#define AUXLED_RGB_PORT PORTC  // PORTA or PORTB or PORTC
+
+// this light has three aux LED channels: R, G, B
+#define USE_AUX_RGB_LEDS
+
+void set_level_main(uint8_t level);
+
+bool gradual_tick_main(uint8_t gt);
+
+
+inline void hwdef_setup() {
+
+    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
+    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB,
+                      CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
+
+    //VPORTA.DIR = ...;
+    // Outputs: PWMs
+    VPORTB.DIR = PIN0_bm
+               | PIN1_bm;
+    // RGB aux LEDs
+    VPORTC.DIR = PIN1_bm
+               | PIN2_bm
+               | PIN3_bm;
+
+    // enable pullups on the unused pins to reduce power
+    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
+    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
+
+    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
+    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
+    PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN5CTRL = PORT_PULLUPEN_bm;
+
+    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
+    //PORTC.PIN1CTRL = PORT_PULLUPEN_bm; // RGB Aux
+    //PORTC.PIN2CTRL = PORT_PULLUPEN_bm; // RGB Aux
+    //PORTC.PIN3CTRL = PORT_PULLUPEN_bm; // RGB Aux
+
+    // set up the PWM
+    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
+    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
+    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
+    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
+    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
+    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
+    // See the manual for other pins, clocks, configs, portmux, etc
+    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm
+                      | TCA_SINGLE_CMP1EN_bm
+                      | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
+    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc
+                      | TCA_SINGLE_ENABLE_bm;
+
+    PWM_TOP = PWM_TOP_INIT;
+
+}
+
+
+#define LAYOUT_DEFINED
+
diff --git a/spaghetti-monster/anduril/cfg-wurkkos-ts25.h b/spaghetti-monster/anduril/cfg-wurkkos-ts25.h
index 3196a9a..446ee26 100644
--- a/spaghetti-monster/anduril/cfg-wurkkos-ts25.h
+++ b/spaghetti-monster/anduril/cfg-wurkkos-ts25.h
@@ -4,7 +4,7 @@
 #pragma once
 
 #define MODEL_NUMBER "0715"
-#include "hwdef-Wurkkos_TS25.h"
+#include "hwdef-wurkkos-ts25.h"
 // ATTINY: 1616
 
 // this light has three aux LED channels: R, G, B
@@ -19,44 +19,60 @@
 #undef VOLTAGE_FUDGE_FACTOR
 #define VOLTAGE_FUDGE_FACTOR 5  // add 0.25V, not 0.35V
 
-/*
-// copied from Emisar D4 ramp
-// ../../bin/level_calc.py 1 65 7135 1 0.8 150
-// ... mixed with this:
-// ../../bin/level_calc.py 2 150 7135 4 0.33 150 FET 1 10 1500
-#define RAMP_LENGTH 150
-#define PWM1_LEVELS 1,1,2,2,3,3,4,4,5,6,7,8,9,10,12,13,14,15,17,19,20,22,24,26,29,31,34,36,39,42,45,48,51,55,59,62,66,70,75,79,84,89,93,99,104,110,115,121,127,134,140,147,154,161,168,176,184,192,200,209,217,226,236,245,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
-#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,3,4,5,7,8,9,11,12,14,15,17,19,20,22,24,25,27,29,31,33,35,37,39,41,43,45,48,50,52,55,57,59,62,64,67,70,72,75,78,81,84,87,90,93,96,99,102,105,109,112,115,119,122,126,129,133,137,141,144,148,152,156,160,165,169,173,177,182,186,191,195,200,205,209,214,219,224,229,234,239,244,250,255
-#define MAX_1x7135 65
-#define HALFSPEED_LEVEL 14
-#define QUARTERSPEED_LEVEL 5
-*/
+#define RAMP_SIZE 150
+
+#if 0  // 2022 version
 // level 1 by hand, for the rest
 // level_calc.py 7.01 2 149 7135 3 0.5 125 FET 1 10 1200 --pwm dyn:63:2048:255
-#define RAMP_LENGTH 150
-#define USE_DYN_PWM
 #define PWM1_LEVELS 1,3,3,4,5,6,7,8,9,10,12,13,14,16,17,19,20,22,24,25,27,29,31,33,35,37,40,42,44,47,49,52,54,57,59,62,64,67,70,72,75,77,80,82,85,87,89,91,93,95,96,98,99,100,100,101,100,100,99,97,95,93,90,86,82,87,91,96,100,106,111,116,122,128,134,141,147,155,162,169,177,186,194,203,213,222,232,243,254,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
 #define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,3,4,6,7,9,11,12,14,16,18,20,22,24,27,29,31,34,37,39,42,45,48,51,54,57,61,64,68,72,75,79,83,88,92,97,101,106,111,116,121,126,132,138,144,150,156,162,169,176,183,190,197,205,213,221,229,237,246,255
 #define PWM_TOPS 2047,2047,1198,1322,1584,1676,1701,1691,1662,1622,1774,1703,1631,1692,1613,1639,1558,1564,1559,1478,1464,1444,1420,1392,1361,1329,1331,1293,1256,1246,1207,1192,1152,1133,1094,1074,1035,1013,991,954,932,897,875,842,820,790,760,731,704,678,646,622,593,566,534,510,478,452,423,393,364,338,310,280,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
 #define MAX_1x7135 90
 #define HALFSPEED_LEVEL 2
 #define QUARTERSPEED_LEVEL 2
+#endif
 
-#define RAMP_SMOOTH_FLOOR 1
-#define RAMP_SMOOTH_CEIL 120
-// 10 28 46 [65] 83 101 120
-#define RAMP_DISCRETE_FLOOR 10
-#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
-#define RAMP_DISCRETE_STEPS 7
+// 7135 at 75/150
+// level_calc.py 5.7895 2 150 7135 1 0.1 130 FET 1 10 3000 --pwm dyn:74:4096:255:3
+// (with some manual tweaks)
+#define PWM1_LEVELS  1,1,2,3,3,4,5,6,7,8,9,11,12,13,15,16,18,19,21,23,26,27,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,71,74,76,78,80,82,85,87,90,93,96,100,103,107,112,116,122,127,133,140,147,154,163,171,182,192,203,215,228,241,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+// non-zero part of FET channel calculated with:
+//   level_calc.py 3 1 75 7135 1 200 3000
+//   (FIXME? there's a visible bump when the FET kicks in, even with just 1/255)
+#define PWM2_LEVELS  0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,2,3,4,6,7,8,10,11,13,14,16,17,19,21,22,24,26,28,30,32,34,37,39,41,44,46,48,51,54,56,59,62,65,68,71,74,77,81,84,87,91,94,98,102,106,110,114,118,122,126,130,135,139,144,148,153,158,163,168,173,178,184,189,195,200,206,212,218,224,230,236,242,248,255
+#define PWM_TOPS     4095,2701,3200,3586,2518,2778,2834,2795,2705,2587,2455,2582,2412,2247,2256,2091,2062,1907,1860,1802,1737,1605,1542,1477,1412,1347,1284,1222,1162,1105,1050,997,946,898,853,810,768,730,693,658,625,594,564,536,503,485,462,439,418,398,384,366,353,340,327,319,307,298,292,284,280,273,269,266,263,260,258,256,256,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+
+#define MAX_1x7135 75
+#define DEFAULT_LEVEL 50
+#define MIN_THERM_STEPDOWN 60
+#define HALFSPEED_LEVEL 20
+#define QUARTERSPEED_LEVEL 5
+
+#define RAMP_SMOOTH_FLOOR    1
+#define RAMP_SMOOTH_CEIL     150
+// 20 38 56 [75] 93 111 130
+#define RAMP_DISCRETE_FLOOR  20
+#define RAMP_DISCRETE_CEIL   130
+#define RAMP_DISCRETE_STEPS  7
 
 // at Wurkkos's request, reduce the Simple UI ceiling a little bit
-#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR
-#define SIMPLE_UI_CEIL 135
-#define SIMPLE_UI_STEPS 5
+// 25 50 [75] 100 125
+#define SIMPLE_UI_FLOOR  25
+#define SIMPLE_UI_CEIL   125
+#define SIMPLE_UI_STEPS  5
 
 // enable 2 click turbo (Anduril 1 style)
 #define DEFAULT_2C_STYLE 1
 
+// stop panicking at ~50% power
+#define THERM_FASTER_LEVEL 120  // throttle back faster when high
+
+// show each channel while it scroll by in the menu
+#define USE_CONFIG_COLORS
+
+// blink numbers on the aux LEDs by default
+#define DEFAULT_BLINK_CHANNEL  CM_AUXWHT
+
 // enable SOS in the blinkies group
 #define USE_SOS_MODE
 #define USE_SOS_MODE_IN_BLINKY_GROUP
@@ -67,16 +83,11 @@
 // allow Aux Config and Strobe Modes in Simple UI
 #define USE_EXTENDED_SIMPLE_UI
 
-// enable factory reset on 13H without loosening tailcap
-#define USE_SOFT_FACTORY_RESET
-
-// stop panicking at ~55% power
-#define THERM_FASTER_LEVEL 130  // throttle back faster when high
-
-// don't blink during the ramp or at the ceiling
+// don't blink mid-ramp
 #ifdef BLINK_AT_RAMP_MIDDLE
 #undef BLINK_AT_RAMP_MIDDLE
 #endif
-#ifdef BLINK_AT_RAMP_CEIL
-#undef BLINK_AT_RAMP_CEIL
-#endif
+
+// enable factory reset on 13H without loosening tailcap
+#define USE_SOFT_FACTORY_RESET
+