diff options
| author | Selene ToyKeeper | 2024-03-12 13:17:47 -0600 |
|---|---|---|
| committer | Selene ToyKeeper | 2024-03-12 13:17:47 -0600 |
| commit | 8dbc5c8b694a5a60b5f2bbc4228037eff119ba68 (patch) | |
| tree | 4e2404dcbc74c175bc9c60a68bb18708f15cb521 /hw/lumintop/fw3x-lume1/README.md | |
| parent | added wurkkos-ts25-boost (early version made from spec, no clue if it works) (diff) | |
| parent | enabled eeprom read/write stabilization by default on recent MCUs, (diff) | |
| download | anduril-8dbc5c8b694a5a60b5f2bbc4228037eff119ba68.tar.gz anduril-8dbc5c8b694a5a60b5f2bbc4228037eff119ba68.tar.bz2 anduril-8dbc5c8b694a5a60b5f2bbc4228037eff119ba68.zip | |
Merge branch 'trunk' into wurkkos-ts25-boost
* trunk:
enabled eeprom read/write stabilization by default on recent MCUs, to prevent corrupt data
thefreeman-avr32dd20-devkit: enable boost bypass at boot, so AA/NiMH can boot
avr32dd20-devkit: use unimplemented "CH" pin as a boost bypass control
added "emisar-2ch-fet-joined" build, for D4S w/ lighted switch
documented FW3X swapped pins better
documented Wurkkos TS25/TS11/FC13 distinctions
build.sh: don't require DFPs, newer avr-libc doesn't need them
use BLIP_LEVEL instead of 0 for "blip"s
clarified which-hex-file.md a bit; make sure the model number matches
fw3x: reduced pulsing on low modes
Diffstat (limited to 'hw/lumintop/fw3x-lume1/README.md')
| -rw-r--r-- | hw/lumintop/fw3x-lume1/README.md | 10 |
1 files changed, 7 insertions, 3 deletions
diff --git a/hw/lumintop/fw3x-lume1/README.md b/hw/lumintop/fw3x-lume1/README.md index 190cd0e..d155eba 100644 --- a/hw/lumintop/fw3x-lume1/README.md +++ b/hw/lumintop/fw3x-lume1/README.md @@ -6,9 +6,10 @@ sensor. ## Notes of interest -**Flashing firmware**: The MOSI and MISO pin are swapped, compared to a Hanklight. -LoneOceans sent a fixed driver design to Lumintop, but the new design didn't -get produced. So to flash firmware, swap the wires for those two pins first. +**Flashing firmware**: The MOSI and MISO pin are swapped on PCBs dated 01/20, +compared to a Hanklight. LoneOceans sent a fixed driver design (dated 06/20) +to Lumintop, but the new design didn't get produced. So to flash firmware, +swap the wires for those two pins first. **Fuses**: Lumintop seems to have shipped the FW3X with the wrong fuse values, so it has the MCU severely underclocked and everything runs much slower than it @@ -29,3 +30,6 @@ output is unstable so there is very visible ripple. The user can either raise the ramp floor to a level high enough to avoid these issues, or learn to live with the ripple and preflash. +LoneOceans has some extra notes here, which mostly apply only to older versions +of the code: https://budgetlightforum.com/t/anduril-2/62656/531 + |