Merge branch 'trunk' into emisar-d3aa

* trunk:
  enabled eeprom read/write stabilization by default on recent MCUs, to prevent corrupt data
  thefreeman-avr32dd20-devkit: enable boost bypass at boot, so AA/NiMH can boot
  avr32dd20-devkit: use unimplemented "CH" pin as a boost bypass control
  added "emisar-2ch-fet-joined" build, for D4S w/ lighted switch
  documented FW3X swapped pins better
  documented Wurkkos TS25/TS11/FC13 distinctions
  build.sh: don't require DFPs, newer avr-libc doesn't need them
  use BLIP_LEVEL instead of 0 for "blip"s
  clarified which-hex-file.md a bit; make sure the model number matches
  fw3x: reduced pulsing on low modes

3 files changed, 35 insertions, 2 deletions

diff --git a/hw/thefreeman/avr32dd20-devkit/anduril.h b/hw/thefreeman/avr32dd20-devkit/anduril.h
index 02d5de3..3152183 100644
--- a/hw/thefreeman/avr32dd20-devkit/anduril.h
+++ b/hw/thefreeman/avr32dd20-devkit/anduril.h
@@ -110,6 +110,7 @@
 
 #define PARTY_STROBE_ONTIME 1  // slow down party strobe
 #define STROBE_OFF_LEVEL 1  // keep the regulator chip on between pulses
+#define BLIP_LEVEL 1  // same
 
 // smoother candle mode with bigger oscillations
 #define CANDLE_AMPLITUDE 40
diff --git a/hw/thefreeman/avr32dd20-devkit/hwdef.c b/hw/thefreeman/avr32dd20-devkit/hwdef.c
index 3e5dd79..460082f 100644
--- a/hw/thefreeman/avr32dd20-devkit/hwdef.c
+++ b/hw/thefreeman/avr32dd20-devkit/hwdef.c
@@ -30,6 +30,11 @@ void set_level_zero() {
     delay_4ms(IN_NFET_DELAY_TIME/4);
     IN_NFET_ENABLE_PORT &= ~(1 << IN_NFET_ENABLE_PIN);
 
+    #ifdef USE_BST_BYPASS
+    // turn off bypass
+    BST_BYPASS_PORT |= (1 << BST_BYPASS_PIN);
+    #endif
+
     // turn off boost last
     BST_ENABLE_PORT &= ~(1 << BST_ENABLE_PIN);  // BST off
 }
@@ -48,6 +53,14 @@ void set_level_main(uint8_t level) {
     // BST on first, to give it a few extra microseconds to spin up
     BST_ENABLE_PORT |= (1 << BST_ENABLE_PIN);
 
+    #ifdef USE_BST_BYPASS
+    // turn on bypass in li-ion mode
+    if (voltage > DUAL_VOLTAGE_FLOOR)
+        BST_BYPASS_PORT &= ~(1 << BST_BYPASS_PIN);  // low = bypass
+    else  // turn off bypass in AA/NiMH mode
+        BST_BYPASS_PORT |= (1 << BST_BYPASS_PIN);  // high = boost
+    #endif
+
     // pre-load ramp data so it can be assigned faster later
     // DAC level register is left-aligned
     PWM1_DATATYPE dac_lvl  = PWM1_GET(level) << 6;
diff --git a/hw/thefreeman/avr32dd20-devkit/hwdef.h b/hw/thefreeman/avr32dd20-devkit/hwdef.h
index f1b6095..38b508d 100644
--- a/hw/thefreeman/avr32dd20-devkit/hwdef.h
+++ b/hw/thefreeman/avr32dd20-devkit/hwdef.h
@@ -28,6 +28,7 @@
  *  18   PA1    G: aux green
  *  19   PA2    B: aux blue
  *  20   PA3    CH: detect charging
+ *              or BBY: boost bypass PFET
  *
  * BST EN enable the boost regulator and Op-Amp
  * DAC sets the current, max current depends on Vset voltage divider and Rsense
@@ -35,6 +36,8 @@
  *         and low value Rsense (high current range, pin high)
  * IN- NFET : pull up after BST enable to eliminate startup flash, pull down otherwise
  * CH senses the status of the onboard charger
+ * BBY routes power around the boost converter in li-ion 3V mode
+ *   (pin low = bypass, pin high = boost)
  * BATT LVL : Vbat * (100.0/(330+100))
  * LVB is for OTSM firmware, not used here
  */
@@ -77,6 +80,11 @@ enum CHANNEL_MODES {
 #define BST_ENABLE_PIN   PIN5_bp
 #define BST_ENABLE_PORT  PORTD_OUT
 
+// BST bypass
+#define USE_BST_BYPASS
+#define BST_BYPASS_PIN   PIN3_bp
+#define BST_BYPASS_PORT  PORTA_OUT
+
 // HDR
 // turns on HDR FET for the high current range
 #define HDR_ENABLE_PIN   PIN7_bp
@@ -133,7 +141,9 @@ inline void hwdef_setup() {
     VPORTA.DIR = PIN0_bm   // R
                | PIN1_bm   // G
                | PIN2_bm   // B
-               //| PIN3_bm   // CH
+               #ifdef USE_BST_BYPASS
+               | PIN3_bm   // BBY
+               #endif
                | PIN7_bm;  // HDR
     VPORTD.DIR = PIN5_bm   // EN
                | PIN6_bm   // DAC
@@ -143,7 +153,10 @@ inline void hwdef_setup() {
     //PORTA.PIN0CTRL = PORT_PULLUPEN_bm;  // R
     //PORTA.PIN1CTRL = PORT_PULLUPEN_bm;  // G
     //PORTA.PIN2CTRL = PORT_PULLUPEN_bm;  // B
-    //PORTA.PIN3CTRL = PORT_PULLUPEN_bm;  // CH
+    #ifdef USE_BST_BYPASS
+    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;  // BBY
+    BST_BYPASS_PORT |= (1 << BST_BYPASS_PIN);
+    #endif
     PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
     PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
     //PORTA.PIN6CTRL = PORT_PULLUPEN_bm;  // BATT LVL
@@ -177,6 +190,12 @@ inline void hwdef_setup() {
     //       to generate a zero without spending power on the DAC
     //       (and do this in set_level_zero() too)
 
+    // TCA/TCB/TCD aren't being used, so turn them off
+    TCA0.SINGLE.CTRLA = 0;
+    TCB0.CTRLA = 0;
+    TCB1.CTRLA = 0;
+    TCD0.CTRLA = 0;
+
 }