merged sofirn sp10-pro branch (should have done it months ago, but forgot)

1 files changed, 0 insertions, 124 deletions

diff --git a/hwdef-Sofirn_SP10S.h b/hwdef-Sofirn_SP10S.h
deleted file mode 100644
index 0ee3332..0000000
--- a/hwdef-Sofirn_SP10S.h
+++ /dev/null
@@ -1,124 +0,0 @@
-#ifndef HWDEF_SOFIRN_SP10S_H
-#define HWDEF_SOFIRN_SP10S_H
-
-// TODO: rename to sofirn-sp10s-gchart?
-
-/* gChart's PIC12 to ATTINY1616 v1 adapter for the SP10S
-https://oshpark.com/shared_projects/b4IZEGSy
-
-PIC12 Pinout:
-1 - VDD
-2 - No Connect
-3 - Low Channel FET (series 4.7K Ohms)
-4 - Switch
-5 - High Channel FET (main PWM)
-6 - Voltage Divider (300K:100K Ohms)
-7 - Boost chip enable
-8 - GND
-
-ATTINY1616 Mapping:
-2 - PA5 : (no connect)
-3 - PB5 : TCA0 - WO2 Alternate MUX
-4 - PB3 : (switch)
-5 - PB0 : TCA0 - WO0
-6 - PB4 : ADC0 - AIN9
-7 - PA1 : (boost enable)
-
-*/
-
-
-#define LAYOUT_DEFINED
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1616
-#include <avr/io.h>
-
-#ifndef SWITCH_PIN
-#define SWITCH_PIN     3
-#define SWITCH_PORT    VPORTB.IN
-#define SWITCH_ISC_REG PORTB.PIN3CTRL
-#define SWITCH_VECT    PORTB_PORT_vect
-#define SWITCH_INTFLG  VPORTB.INTFLAGS
-#endif
-
-#define PWM_CHANNELS 2
-
-// Small channel
-#ifndef PWM1_PIN
-#define PWM1_PIN PB5
-#define PWM1_LVL TCA0.SINGLE.CMP2  // PB5 is Alternate MUX for TCA Compare 2
-#endif
-
-// Big channel
-#ifndef PWM2_PIN
-#define PWM2_PIN PB0
-#define PWM2_LVL TCA0.SINGLE.CMP0  // PB0 is TCA Compare 0
-#endif
-
-#define LED_ENABLE_PIN   PIN1_bp
-#define LED_ENABLE_PORT  PORTA_OUT
-
-#define USE_VOLTAGE_DIVIDER       // use a dedicated pin, not VCC, because VCC input is flattened
-#define DUAL_VOLTAGE_FLOOR    20  // for AA/14500 boost drivers, don't indicate low voltage if below this level
-#define DUAL_VOLTAGE_LOW_LOW  07  // the lower voltage range's danger zone 0.7 volts
-#define ADMUX_VOLTAGE_DIVIDER ADC_MUXPOS_AIN9_gc  // which ADC channel to read
-
-// Raw ADC readings at 4.4V and 2.2V
-// calibrate the voltage readout here
-// estimated / calculated values are:
-//   (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
-// Resistors are 300,000 and 100,000
-#ifndef ADC_44
-#define ADC_44 1023  // raw value at 4.40V
-#endif
-#ifndef ADC_22
-#define ADC_22 512  // raw value at 2.20V
-#endif
-
-
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
-
-    // set up the system clock to run at 5 MHz instead of the default 3.33 MHz
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_4X_gc | CLKCTRL_PEN_bm );
-
-    VPORTA.DIR = PIN1_bm;  // Boost enable pin
-    VPORTB.DIR = PIN0_bm | PIN5_bm;  // PWM pins as output
-    //VPORTC.DIR = ...;
-
-    // enable pullups on the input pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    //PORTA.PIN1CTRL = PORT_PULLUPEN_bm; // Boost enable pin
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // Big PWM channel
-    PORTB.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN3CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // Switch
-    //PORTB.PIN4CTRL = PORT_PULLUPEN_bm; // Voltage divider
-    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Small PWM channel
-
-    //PORTC.PIN0CTRL = PORT_PULLUPEN_bm; connected to the ADC via airwire
-    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-
-    // set up the PWM
-    // TODO: add references to MCU documentation
-    PORTMUX.CTRLC = PORTMUX_TCA02_ALTERNATE_gc;  // Use alternate pin for TCA0:WO2
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP2EN_bm | TCA_SINGLE_WGMODE_SINGLESLOPE_gc;
-    TCA0.SINGLE.PER = 255;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
-}
-
-
-#endif