diff options
Diffstat (limited to '')
| -rw-r--r-- | hwdef-Noctigon_K1-SBT90.h | 143 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-noctigon-k1-sbt90.h | 61 |
2 files changed, 204 insertions, 0 deletions
diff --git a/hwdef-Noctigon_K1-SBT90.h b/hwdef-Noctigon_K1-SBT90.h new file mode 100644 index 0000000..c19a4a6 --- /dev/null +++ b/hwdef-Noctigon_K1-SBT90.h @@ -0,0 +1,143 @@ +#ifndef HWDEF_NOCTIGON_K1SBT90_H +#define HWDEF_NOCTIGON_K1SBT90_H + +/* Noctigon K1-SBT90.2 driver layout (attiny1634) + * (mostly the same as KR4 driver) + * + * Pin / Name / Function + * 1 PA6 FET PWM (direct drive) (PWM1B) + * 2 PA5 R: red aux LED (PWM0B) + * 3 PA4 G: green aux LED + * 4 PA3 B: blue aux LED + * 5 PA2 (none) + * 6 PA1 (none) + * 7 PA0 (none) + * 8 GND GND + * 9 VCC VCC + * 10 PC5 (none) + * 11 PC4 (none) + * 12 PC3 RESET + * 13 PC2 (none) + * 14 PC1 SCK + * 15 PC0 (none) PWM0A + * 16 PB3 main LED PWM (linear) (PWM1A) + * 17 PB2 MISO / e-switch (PCINT10) + * 18 PB1 MOSI / battery voltage (ADC6) + * 19 PB0 Opamp power + * 20 PA7 (none) + * ADC12 thermal sensor + * + * Main LED power uses one pin to turn the Opamp on/off, + * and one pin to control Opamp power level. + * Main brightness control uses the power level pin, with 4 kHz 10-bit PWM. + * The on/off pin is only used to turn the main LED on and off, + * not to change brightness. + * Also has a direct-drive FET for turbo. + */ + +#ifdef ATTINY +#undef ATTINY +#endif +#define ATTINY 1634 +#include <avr/io.h> + +#define PWM_CHANNELS 2 +#define PWM_BITS 10 // 0 to 1023 at 4 kHz, not 0 to 255 at 16 kHz +#define PWM_TOP 1023 + +#define SWITCH_PIN PB2 // pin 17 +#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt +#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] +#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] +#define SWITCH_PORT PINB // PINA or PINB or PINC +#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] + +#define PWM1_PIN PB3 // pin 16, Opamp reference +#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 + +#define PWM2_PIN PA6 // pin 1, DD FET PWM +#define PWM2_LVL OCR1B // OCR1B is the output compare register for PA6 + +#define LED_ENABLE_PIN PB0 // pin 19, Opamp power +#define LED_ENABLE_PORT PORTB // control port for PB0 + + +#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened +#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 +// pin to ADC mappings are in DS table 19-4 +#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 +// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 +#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D +// DS tables 19-3, 19-4 +// Bit 7 6 5 4 3 2 1 0 +// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 +// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 +// divided by ... +// REFS[1:0] = 1, 0 for internal 1.1V reference +// other bits reserved +#define ADMUX_VOLTAGE_DIVIDER 0b10000110 +#define ADC_PRSCL 0x07 // clk/128 + +// TODO: calibrate this +// Raw ADC readings at 4.4V and 2.2V +// calibrate the voltage readout here +// estimated / calculated values are: +// (voltage - D1) * (R2/(R2+R1) * 256 / 1.1) +// D1, R1, R2 = 0, 330, 100 +#ifndef ADC_44 +//#define ADC_44 981 // raw value at 4.40V +#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 +#endif +#ifndef ADC_22 +//#define ADC_22 489 // raw value at 2.20V +#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 +#endif + +#define TEMP_CHANNEL 0b00001111 + +// this light has aux LEDs under the optic +#define AUXLED_R_PIN PA5 // pin 2 +#define AUXLED_G_PIN PA4 // pin 3 +#define AUXLED_B_PIN PA3 // pin 4 +#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC +#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC +#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC + +// with so many pins, doing this all with #ifdefs gets awkward... +// ... so just hardcode it in each hwdef file instead +inline void hwdef_setup() { + // enable output ports + // Opamp level and Opamp on/off + DDRB = (1 << PWM1_PIN) + | (1 << LED_ENABLE_PIN); + // DD FET PWM, aux R/G/B + DDRA = (1 << PWM2_PIN) + | (1 << AUXLED_R_PIN) + | (1 << AUXLED_G_PIN) + | (1 << AUXLED_B_PIN) + ; + + // configure PWM + // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter + // pre-scale for timer: N = 1 + // WGM1[3:0]: 0,0,1,1: PWM, Phase Correct, 10-bit (DS table 12-5) + // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) + // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) + // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) + TCCR1A = (1<<WGM11) | (1<<WGM10) // 10-bit (TOP=0x03FF) (DS table 12-5) + | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) + | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) + ; + TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) + | (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5) + ; + + // set up e-switch + //PORTB = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? + PUEB = (1 << SWITCH_PIN); // pull-up for e-switch + SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt +} + +#define LAYOUT_DEFINED + +#endif diff --git a/spaghetti-monster/anduril/cfg-noctigon-k1-sbt90.h b/spaghetti-monster/anduril/cfg-noctigon-k1-sbt90.h new file mode 100644 index 0000000..fd98979 --- /dev/null +++ b/spaghetti-monster/anduril/cfg-noctigon-k1-sbt90.h @@ -0,0 +1,61 @@ +// Noctigon K1-SBT90.2 config options for Anduril +// (is a K1 host with a KR4-like driver and a really high-powered LED) +#include "hwdef-Noctigon_K1-SBT90.h" +// ATTINY: 1634 + +// this light can safely run a bit hotter than most +#undef DEFAULT_THERM_CEIL +#define DEFAULT_THERM_CEIL 55 + +// this light has three aux LED channels: R, G, B +#define USE_AUX_RGB_LEDS +#define USE_AUX_RGB_LEDS_WHILE_ON +#define USE_INDICATOR_LED_WHILE_RAMPING +#define RGB_LED_OFF_DEFAULT 0x18 // low, voltage +#define RGB_LED_LOCKOUT_DEFAULT 0x37 // blinking, rainbow +#define RGB_RAINBOW_SPEED 0x03 // half a second per color + +// enable blinking aux LEDs +#define TICK_DURING_STANDBY +#define STANDBY_TICK_SPEED 3 // every 0.128 s + + +// brightness: +// 0/1023: 0.35 lm +// 1/1023: 2.56 lm +// max regulated: 1740 lm +// FET: ~3700 lm +// maxreg at 130: level_calc.py cube 2 150 7135 0 2.5 1740 FET 1 10 2565 +// maxreg at 120: level_calc.py cube 2 150 7135 0 2.5 1740 FET 1 10 3190 +#define RAMP_LENGTH 150 +#define PWM1_LEVELS 0,0,1,1,2,2,3,3,4,4,5,6,7,8,9,10,11,13,14,15,17,19,20,22,24,26,28,30,33,35,38,40,43,46,49,52,55,59,62,66,70,74,78,82,86,91,96,100,105,111,116,121,127,133,139,145,151,158,165,172,179,186,193,201,209,217,225,234,243,251,261,270,280,289,299,310,320,331,342,353,364,376,388,400,412,425,438,451,464,478,492,506,521,536,551,566,582,597,614,630,647,664,681,699,717,735,754,772,792,811,831,851,871,892,913,935,956,978,1001,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,1023,0 +#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,22,51,79,109,138,168,198,229,260,292,324,357,390,423,457,492,527,562,598,634,671,708,746,784,822,861,901,941,982,1023 +#define DEFAULT_LEVEL 46 +#define MAX_1x7135 120 +#define HALFSPEED_LEVEL 10 +#define QUARTERSPEED_LEVEL 2 + +#define RAMP_SMOOTH_FLOOR 3 // level 1 is unreliable +#define RAMP_SMOOTH_CEIL 120 +// 10, 28, [46], 65, 83, 101, [120] +#define RAMP_DISCRETE_FLOOR 10 +#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL +#define RAMP_DISCRETE_STEPS 7 + +#define MUGGLE_FLOOR RAMP_DISCRETE_FLOOR +#define MUGGLE_CEILING 65 + +// stop panicking at ~25% power or ~1000 lm +#define THERM_FASTER_LEVEL 120 +#define MIN_THERM_STEPDOWN DEFAULT_LEVEL +//#define THERM_NEXT_WARNING_THRESHOLD 16 // accumulate less error before adjusting +//#define THERM_RESPONSE_MAGNITUDE 128 // bigger adjustments + +// easier access to thermal config mode, for Noctigon +#define USE_TENCLICK_THERMAL_CONFIG + +// slow down party strobe; this driver can't pulse for 1ms or less +//#define PARTY_STROBE_ONTIME 2 + +#define THERM_CAL_OFFSET 5 + |