diff options
Diffstat (limited to '')
| -rw-r--r-- | hwdef-BLF_GT.h | 40 | ||||
| -rw-r--r-- | hwdef-BLF_Q8.h | 16 | ||||
| -rw-r--r-- | hwdef-Emisar_D4.h | 36 | ||||
| -rw-r--r-- | hwdef-Emisar_D4S.h | 10 | ||||
| -rw-r--r-- | hwdef-FET_7135.h | 32 | ||||
| -rw-r--r-- | hwdef-FW3A.h | 35 | ||||
| -rw-r--r-- | hwdef-Ferrero_Rocher.h | 11 | ||||
| -rw-r--r-- | hwdef-TK_Saber.h | 33 | ||||
| -rw-r--r-- | hwdef-Tripledown.h | 33 | ||||
| -rw-r--r-- | hwdef-nanjg.h | 16 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/anduril.c | 101 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-blf-gt.h | 24 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-blf-q8.h | 9 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-emisar-d4.h | 1 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-fw3a.h | 1 | ||||
| -rw-r--r-- | tk-attiny.h | 289 |
16 files changed, 373 insertions, 314 deletions
diff --git a/hwdef-BLF_GT.h b/hwdef-BLF_GT.h new file mode 100644 index 0000000..1a05741 --- /dev/null +++ b/hwdef-BLF_GT.h @@ -0,0 +1,40 @@ +/* BLF GT driver layout + * ---- + * Reset -|1 8|- VCC (unused) + * eswitch -|2 7|- Voltage divider + * AUX LED -|3 6|- Current control (buck level) + * GND -|4 5|- PWM (buck output on/off) + * ---- + */ + +#define PWM_CHANNELS 2 + +#define AUXLED_PIN PB4 // pin 3 + +#define SWITCH_PIN PB3 // pin 2 +#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt + +#define PWM1_PIN PB0 // pin 5, 1x7135 PWM +#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 +#define PWM2_PIN PB1 // pin 6, FET PWM +#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 + +#define USE_VOLTAGE_DIVIDER // use a voltage divider on pin 7, not VCC +#define VOLTAGE_PIN PB2 // pin 7, voltage ADC +#define VOLTAGE_CHANNEL 0x01 // MUX 01 corresponds with PB2 +// 1.1V reference, left-adjust, ADC1/PB2 +//#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | (1 << ADLAR) | VOLTAGE_CHANNEL) +// 1.1V reference, no left-adjust, ADC1/PB2 +#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | VOLTAGE_CHANNEL) +#define VOLTAGE_ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +// Raw ADC readings at 4.4V and 2.2V (in-between, we assume values form a straight line) +#define ADC_44 184 +#define ADC_22 92 + +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-BLF_Q8.h b/hwdef-BLF_Q8.h new file mode 100644 index 0000000..f00c392 --- /dev/null +++ b/hwdef-BLF_Q8.h @@ -0,0 +1,16 @@ +/* BLF Q8 driver layout + */ +// Q8 driver is the same as a D4, basically +#include "hwdef-Emisar_D4.h" + +// ... except the Q8 has a lighted button +#ifndef AUXLED_PIN +#define AUXLED_PIN PB4 // pin 3 +#endif + +// average drop across diode on this hardware +#ifdef VOLTAGE_FUDGE_FACTOR +#undef VOLTAGE_FUDGE_FACTOR +#endif +#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V + diff --git a/hwdef-Emisar_D4.h b/hwdef-Emisar_D4.h new file mode 100644 index 0000000..105d3b9 --- /dev/null +++ b/hwdef-Emisar_D4.h @@ -0,0 +1,36 @@ +/* Emisar D4 driver layout + * ---- + * Reset -|1 8|- VCC + * eswitch -|2 7|- + * AUX LED -|3 6|- PWM (FET) + * GND -|4 5|- PWM (1x7135) + * ---- + */ + +#define PWM_CHANNELS 2 + +#define AUXLED_PIN PB4 // pin 3 + +#define SWITCH_PIN PB3 // pin 2 +#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt + +#define PWM1_PIN PB0 // pin 5, 1x7135 PWM +#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 +#define PWM2_PIN PB1 // pin 6, FET PWM +#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 + +// (FIXME: remove? not used?) +#define VOLTAGE_PIN PB2 // pin 7, voltage ADC +#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 +#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +// average drop across diode on this hardware +#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V + +//#define TEMP_DIDR ADC4D +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-Emisar_D4S.h b/hwdef-Emisar_D4S.h new file mode 100644 index 0000000..47ef1eb --- /dev/null +++ b/hwdef-Emisar_D4S.h @@ -0,0 +1,10 @@ +/* Emisar D4S driver layout + */ +// same as a D4, basically +#include "hwdef-Emisar_D4.h" + +// ... except the D4S has aux LEDs under the optic +#ifndef AUXLED_PIN +#define AUXLED_PIN PB4 // pin 3 +#endif + diff --git a/hwdef-FET_7135.h b/hwdef-FET_7135.h new file mode 100644 index 0000000..58df7b2 --- /dev/null +++ b/hwdef-FET_7135.h @@ -0,0 +1,32 @@ +/* FET + 7135 driver layout + * ---- + * Reset -|1 8|- VCC + * OTC -|2 7|- Voltage ADC + * Star 3 -|3 6|- PWM (FET) + * GND -|4 5|- PWM (1x7135) + * ---- + */ + +#define STAR2_PIN PB0 // If this pin isn't used for ALT_PWM +#define STAR3_PIN PB4 // pin 3 + +#define CAP_PIN PB3 // pin 2, OTC +#define CAP_CHANNEL 0x03 // MUX 03 corresponds with PB3 (Star 4) +#define CAP_DIDR ADC3D // Digital input disable bit corresponding with PB3 + +#define PWM_PIN PB1 // pin 6, FET PWM +#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 +#define ALT_PWM_PIN PB0 // pin 5, 1x7135 PWM +#define ALT_PWM_LVL OCR0A // OCR0A is the output compare register for PB0 + +#define VOLTAGE_PIN PB2 // pin 7, voltage ADC +#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 +#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +//#define TEMP_DIDR ADC4D +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-FW3A.h b/hwdef-FW3A.h new file mode 100644 index 0000000..5e253c7 --- /dev/null +++ b/hwdef-FW3A.h @@ -0,0 +1,35 @@ +/* BLF/TLF FW3A driver layout + * ---- + * Reset -|1 8|- VCC + * eswitch -|2 7|- optic nerve + * FET -|3 6|- 7x7135 + * GND -|4 5|- 1x7135 + * ---- + */ + +#define PWM_CHANNELS 3 + +#define SWITCH_PIN PB3 // pin 2 +#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt + +#define PWM1_PIN PB0 // pin 5, 1x7135 PWM +#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 +#define PWM2_PIN PB1 // pin 6, FET PWM +#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 +#define PWM3_PIN PB4 // pin 3 +#define PWM3_LVL OCR1B + +#define VISION_PIN PB2 // pin 7, optic nerve +#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 +#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +// average drop across diode on this hardware +#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V + +//#define TEMP_DIDR ADC4D +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-Ferrero_Rocher.h b/hwdef-Ferrero_Rocher.h new file mode 100644 index 0000000..a46f19d --- /dev/null +++ b/hwdef-Ferrero_Rocher.h @@ -0,0 +1,11 @@ +/* Ferrero Rocher driver layout + * ---- + * Reset -|1 8|- VCC + * E-switch -|2 7|- Voltage ADC + * Red LED -|3 6|- PWM + * GND -|4 5|- Green LED + * ---- + */ +// TODO: fill in this section, update Ferrero_Rocher code to use it. +#define FAST 0x23 // fast PWM channel 1 only +#define PHASE 0x21 // phase-correct PWM channel 1 only diff --git a/hwdef-TK_Saber.h b/hwdef-TK_Saber.h new file mode 100644 index 0000000..e90d5dd --- /dev/null +++ b/hwdef-TK_Saber.h @@ -0,0 +1,33 @@ +/* TK 4-color lightsaber driver layout + * ---- + * Reset -|1 8|- VCC + * PWM 4 (A) -|2 7|- e-switch + * PWM 3 (G) -|3 6|- PWM 2 (B) + * GND -|4 5|- PWM 1 (R) + * ---- + */ + +#define PWM_CHANNELS 4 +#define PWM1_PIN PB0 // pin 5 +#define PWM1_LVL OCR0A +#define PWM2_PIN PB1 // pin 6 +#define PWM2_LVL OCR0B +#define PWM3_PIN PB4 // pin 3 +#define PWM3_LVL OCR1B +#define PWM4_PIN PB3 // pin 2 +#define PWM4_LVL OCR1A + +#define SWITCH_PIN PB2 // pin 7 +#define SWITCH_PCINT PCINT2 // pin 7 pin change interrupt + +#define ADC_PRSCL 0x06 // clk/64 (no need to be super fast) + +// average drop across diode on this hardware +#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V + +//#define TEMP_DIDR ADC4D +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-Tripledown.h b/hwdef-Tripledown.h new file mode 100644 index 0000000..4676e69 --- /dev/null +++ b/hwdef-Tripledown.h @@ -0,0 +1,33 @@ +/* Tripledown driver layout + * ---- + * Reset -|1 8|- VCC + * OTC -|2 7|- Voltage ADC + * PWM (FET) -|3 6|- PWM (6x7135) + * GND -|4 5|- PWM (1x7135) + * ---- + */ + +#define STAR2_PIN PB0 // If this pin isn't used for ALT_PWM + +#define CAP_PIN PB3 // pin 2, OTC +#define CAP_CHANNEL 0x03 // MUX 03 corresponds with PB3 (Star 4) +#define CAP_DIDR ADC3D // Digital input disable bit corresponding with PB3 + +#define PWM_PIN PB1 // pin 6, 6x7135 PWM +#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 +#define ALT_PWM_PIN PB0 // pin 5, 1x7135 PWM +#define ALT_PWM_LVL OCR0A // OCR0A is the output compare register for PB0 +#define FET_PWM_PIN PB4 // pin 3 +#define FET_PWM_LVL OCR1B // output compare register for PB4 + +#define VOLTAGE_PIN PB2 // pin 7, voltage ADC +#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 +#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +//#define TEMP_DIDR ADC4D +#define TEMP_CHANNEL 0b00001111 + +#define FAST 0xA3 // fast PWM both channels +#define PHASE 0xA1 // phase-correct PWM both channels + diff --git a/hwdef-nanjg.h b/hwdef-nanjg.h new file mode 100644 index 0000000..add10d1 --- /dev/null +++ b/hwdef-nanjg.h @@ -0,0 +1,16 @@ +/* NANJG driver layout + */ +#define STAR2_PIN PB0 +#define STAR3_PIN PB4 +#define STAR4_PIN PB3 +#define PWM_PIN PB1 +#define VOLTAGE_PIN PB2 +#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 +#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 +#define ADC_PRSCL 0x06 // clk/64 + +#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 + +#define FAST 0x23 // fast PWM channel 1 only +#define PHASE 0x21 // phase-correct PWM channel 1 only + diff --git a/spaghetti-monster/anduril/anduril.c b/spaghetti-monster/anduril/anduril.c index 2fec5b4..a79220b 100644 --- a/spaghetti-monster/anduril/anduril.c +++ b/spaghetti-monster/anduril/anduril.c @@ -26,7 +26,8 @@ //#define FSM_FW3A_DRIVER //#define FSM_BLF_GT_DRIVER -#define USE_LVP +#define USE_LVP // FIXME: won't build when this option is turned off + #define USE_THERMAL_REGULATION #define DEFAULT_THERM_CEIL 50 #define MIN_THERM_STEPDOWN MAX_1x7135 // lowest value it'll step down to @@ -35,19 +36,35 @@ #else #define THERM_DOUBLE_SPEED_LEVEL (RAMP_LENGTH*4/5) // throttle back faster when high #endif -#define USE_SET_LEVEL_GRADUALLY +#ifdef USE_THERMAL_REGULATION +#define USE_SET_LEVEL_GRADUALLY // isn't used except for thermal adjustments +#endif + +// short blips while ramping #define BLINK_AT_CHANNEL_BOUNDARIES //#define BLINK_AT_RAMP_FLOOR #define BLINK_AT_RAMP_CEILING -//#define BLINK_AT_STEPS +//#define BLINK_AT_STEPS // whenever a discrete ramp mode is passed in smooth mode + +// ramp down via regular button hold if a ramp-up ended <1s ago +// ("hold, release, hold" ramps down instead of up) +#define USE_REVERSING + +// battery readout style (pick one) #define BATTCHECK_VpT +//#define BATTCHECK_8bars // FIXME: breaks build +//#define BATTCHECK_4bars // FIXME: breaks build + +// enable/disable various modes #define USE_LIGHTNING_MODE #define USE_CANDLE_MODE +#define USE_MUGGLE_MODE + #define GOODNIGHT_TIME 60 // minutes (approximately) #define GOODNIGHT_LEVEL 24 // ~11 lm -#define USE_REVERSING + +// dual-switch support (second switch is a tail clicky) //#define START_AT_MEMORIZED_LEVEL -#define USE_MUGGLE_MODE /********* Configure SpaghettiMonster *********/ #define USE_DELAY_ZERO @@ -62,45 +79,29 @@ #else #define MAX_CLICKS 5 #endif -#define USE_IDLE_MODE +#define USE_IDLE_MODE // reduce power use while awake and no tasks are pending #define USE_DYNAMIC_UNDERCLOCKING // cut clock speed at very low modes for better efficiency +// full FET strobe can be a bit much... use max regulated level instead, +// if there's a bright enough regulated level +#ifdef MAX_Nx7135 +#define STROBE_BRIGHTNESS MAX_Nx7135 +#else +#define STROBE_BRIGHTNESS MAX_LEVEL +#endif + // specific settings for known driver types -#ifdef FSM_BLF_Q8_DRIVER -#define USE_INDICATOR_LED -#define USE_INDICATOR_LED_WHILE_RAMPING -#define TICK_DURING_STANDBY -#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V - -#elif defined(FSM_EMISAR_D4S_DRIVER) -#define USE_INDICATOR_LED -#define TICK_DURING_STANDBY -#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V -#define RAMP_SMOOTH_CEIL (MAX_LEVEL*4/5) -#undef MIN_THERM_STEPDOWN // this should be lower, because 3x7135 instead of 1x7135 -#define MIN_THERM_STEPDOWN 60 // lowest value it'll step down to -#undef THERM_DOUBLE_SPEED_LEVEL // this should be lower too, because this light is a hot rod -#define THERM_DOUBLE_SPEED_LEVEL (RAMP_LENGTH*2/3) // throttle back faster when high +#if defined(FSM_BLF_GT_DRIVER) +#include "cfg-blf-gt.h" + +#elif FSM_BLF_Q8_DRIVER +#include "cfg-blf-q8.h" #elif defined(FSM_EMISAR_D4_DRIVER) -#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V +#include "cfg-emisar-d4.h" #elif defined(FSM_FW3A_DRIVER) -#define VOLTAGE_FUDGE_FACTOR 5 // add 0.25V - -#elif defined(FSM_BLF_GT_DRIVER) -#define USE_INDICATOR_LED -#define USE_INDICATOR_LED_WHILE_RAMPING -#define TICK_DURING_STANDBY -#undef BLINK_AT_CHANNEL_BOUNDARIES -#undef BLINK_AT_RAMP_CEILING -#undef BLINK_AT_RAMP_FLOOR -//#undef USE_SET_LEVEL_GRADUALLY -#define RAMP_SMOOTH_FLOOR 1 -#define RAMP_SMOOTH_CEIL POWER_80PX -#define RAMP_DISCRETE_FLOOR 1 -#define RAMP_DISCRETE_CEIL POWER_80PX -#define RAMP_DISCRETE_STEPS 7 +#include "cfg-fw3a.h" #endif @@ -137,14 +138,6 @@ #endif #define NUM_STROBES (NUM_STROBES_BASE+ADD_LIGHTNING_STROBE+ADD_CANDLE_MODE) -// full FET strobe can be a bit much... use max regulated level instead, -// if there's a bright enough regulated level -#ifdef MAX_Nx7135 -#define STROBE_BRIGHTNESS MAX_Nx7135 -#else -#define STROBE_BRIGHTNESS MAX_LEVEL -#endif - #include "spaghetti-monster.h" @@ -236,13 +229,12 @@ uint8_t ramp_discrete_step_size; // don't set this #ifdef USE_INDICATOR_LED // bits 2-3 control lockout mode // bits 0-1 control "off" mode -// modes are: 0=off, 1=low, 2=high -// (TODO: 3=blinking) +// modes are: 0=off, 1=low, 2=high, 3=blinking (if TICK_DURING_STANDBY enabled) #ifdef FSM_EMISAR_D4S_DRIVER uint8_t indicator_led_mode = (3<<2) + 1; #else -uint8_t indicator_led_mode = (1<<2) + 2; -//uint8_t indicator_led_mode = (2<<2) + 1; +//uint8_t indicator_led_mode = (1<<2) + 2; +uint8_t indicator_led_mode = (2<<2) + 1; #endif #endif @@ -686,6 +678,9 @@ uint8_t strobe_state(EventPtr event, uint16_t arg) { // (maybe I should just make it nonvolatile?) uint8_t st = strobe_type; #ifdef USE_CANDLE_MODE + // FIXME: make candle variance magnitude a compile-time option, + // since 20 is sometimes too much or too little, + // depending on the driver type and ramp shape //#define MAX_CANDLE_LEVEL (RAMP_SIZE-8-6-4) #define MAX_CANDLE_LEVEL (RAMP_SIZE/2) static uint8_t candle_wave1 = 0; @@ -969,6 +964,8 @@ uint8_t lockout_state(EventPtr event, uint16_t arg) { // momentary(ish) moon mode during lockout // not all presses will be counted; // it depends on what is in the master event_sequences table + // FIXME: maybe do this only if arg == 0? + // (so it'll only get turned on once, instead of every frame) uint8_t last = 0; for(uint8_t i=0; pgm_read_byte(event + i) && (i<EV_MAX_LEN); i++) last = pgm_read_byte(event + i); @@ -1032,6 +1029,12 @@ uint8_t lockout_state(EventPtr event, uint16_t arg) { } // click, click, hold: rotate through indicator LED modes (off mode) else if (event == EV_click3_hold) { + #ifndef USE_INDICATOR_LED_WHILE_RAMPING + // if main LED obscures aux LEDs, turn it off + // FIXME: might not work, since it was turned on just a few clock + // cycles ago at beginning of this function + set_level(0); + #endif #ifdef TICK_DURING_STANDBY uint8_t mode = (arg >> 5) & 3; #else diff --git a/spaghetti-monster/anduril/cfg-blf-gt.h b/spaghetti-monster/anduril/cfg-blf-gt.h new file mode 100644 index 0000000..904668a --- /dev/null +++ b/spaghetti-monster/anduril/cfg-blf-gt.h @@ -0,0 +1,24 @@ +// BLF GT config options for Anduril + +// the button lights up +#define USE_INDICATOR_LED +// the button is visible while main LEDs are on +#define USE_INDICATOR_LED_WHILE_RAMPING +// enable blinking indicator LED while off +#define TICK_DURING_STANDBY + +// don't blink during ramp, it's irrelevant and annoying on this light +#undef BLINK_AT_CHANNEL_BOUNDARIES +#undef BLINK_AT_RAMP_CEILING +#undef BLINK_AT_RAMP_FLOOR + +//#undef USE_SET_LEVEL_GRADUALLY + +// use 2.0 A as the ceiling, 2.5 A only for turbo +// start both ramps at the bottom; even moon throws a long way on the GT +#define RAMP_SMOOTH_FLOOR 1 +#define RAMP_SMOOTH_CEIL POWER_80PX +#define RAMP_DISCRETE_FLOOR 1 +#define RAMP_DISCRETE_CEIL POWER_80PX +#define RAMP_DISCRETE_STEPS 7 + diff --git a/spaghetti-monster/anduril/cfg-blf-q8.h b/spaghetti-monster/anduril/cfg-blf-q8.h new file mode 100644 index 0000000..929fb55 --- /dev/null +++ b/spaghetti-monster/anduril/cfg-blf-q8.h @@ -0,0 +1,9 @@ +// BLF Q8 config options for Anduril + +// the button lights up +#define USE_INDICATOR_LED +// the button is visible while main LEDs are on +#define USE_INDICATOR_LED_WHILE_RAMPING +// enable blinking indicator LED while off +#define TICK_DURING_STANDBY + diff --git a/spaghetti-monster/anduril/cfg-emisar-d4.h b/spaghetti-monster/anduril/cfg-emisar-d4.h new file mode 100644 index 0000000..5421110 --- /dev/null +++ b/spaghetti-monster/anduril/cfg-emisar-d4.h @@ -0,0 +1 @@ +// Emisar D4 config options for Anduril diff --git a/spaghetti-monster/anduril/cfg-fw3a.h b/spaghetti-monster/anduril/cfg-fw3a.h new file mode 100644 index 0000000..420eaeb --- /dev/null +++ b/spaghetti-monster/anduril/cfg-fw3a.h @@ -0,0 +1 @@ +// FW3A config options for Anduril diff --git a/tk-attiny.h b/tk-attiny.h index 347acc7..4973ed5 100644 --- a/tk-attiny.h +++ b/tk-attiny.h @@ -61,282 +61,41 @@ #include <avr/interrupt.h> /******************** I/O pin and register layout ************************/ -#ifdef FET_7135_LAYOUT -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * OTC -|2 7|- Voltage ADC - * Star 3 -|3 6|- PWM (FET) - * GND -|4 5|- PWM (1x7135) - * ---- - */ - -#define STAR2_PIN PB0 // If this pin isn't used for ALT_PWM -#define STAR3_PIN PB4 // pin 3 - -#define CAP_PIN PB3 // pin 2, OTC -#define CAP_CHANNEL 0x03 // MUX 03 corresponds with PB3 (Star 4) -#define CAP_DIDR ADC3D // Digital input disable bit corresponding with PB3 - -#define PWM_PIN PB1 // pin 6, FET PWM -#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 -#define ALT_PWM_PIN PB0 // pin 5, 1x7135 PWM -#define ALT_PWM_LVL OCR0A // OCR0A is the output compare register for PB0 - -#define VOLTAGE_PIN PB2 // pin 7, voltage ADC -#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 - -//#define TEMP_DIDR ADC4D -#define TEMP_CHANNEL 0b00001111 - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - -#endif // FET_7135_LAYOUT - -#ifdef TRIPLEDOWN_LAYOUT -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * OTC -|2 7|- Voltage ADC - * PWM (FET) -|3 6|- PWM (6x7135) - * GND -|4 5|- PWM (1x7135) - * ---- - */ - -#define STAR2_PIN PB0 // If this pin isn't used for ALT_PWM - -#define CAP_PIN PB3 // pin 2, OTC -#define CAP_CHANNEL 0x03 // MUX 03 corresponds with PB3 (Star 4) -#define CAP_DIDR ADC3D // Digital input disable bit corresponding with PB3 - -#define PWM_PIN PB1 // pin 6, 6x7135 PWM -#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 -#define ALT_PWM_PIN PB0 // pin 5, 1x7135 PWM -#define ALT_PWM_LVL OCR0A // OCR0A is the output compare register for PB0 -#define FET_PWM_PIN PB4 // pin 3 -#define FET_PWM_LVL OCR1B // output compare register for PB4 - -#define VOLTAGE_PIN PB2 // pin 7, voltage ADC -#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 - -//#define TEMP_DIDR ADC4D -#define TEMP_CHANNEL 0b00001111 - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - -#endif // TRIPLEDOWN_LAYOUT - -#ifdef FERRERO_ROCHER_LAYOUT -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * E-switch -|2 7|- Voltage ADC - * Red LED -|3 6|- PWM - * GND -|4 5|- Green LED - * ---- - */ -// TODO: fill in this section, update Ferrero_Rocher code to use it. -#define FAST 0x23 // fast PWM channel 1 only -#define PHASE 0x21 // phase-correct PWM channel 1 only -#endif // FERRERO_ROCHER_LAYOUT - -#ifdef NANJG_LAYOUT -#define DRIVER_TYPE_DEFINED -#define STAR2_PIN PB0 -#define STAR3_PIN PB4 -#define STAR4_PIN PB3 -#define PWM_PIN PB1 -#define VOLTAGE_PIN PB2 -#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 - -#define PWM_LVL OCR0B // OCR0B is the output compare register for PB1 - -#define FAST 0x23 // fast PWM channel 1 only -#define PHASE 0x21 // phase-correct PWM channel 1 only - -#endif // NANJG_LAYOUT - - -// Q8 driver is the same as a D4, basically -#ifdef FSM_BLF_Q8_DRIVER -#define FSM_EMISAR_D4_DRIVER -#endif - - -// D4S driver is the same as a D4, basically -#ifdef FSM_EMISAR_D4S_DRIVER -#define FSM_EMISAR_D4_DRIVER -#endif - - -#ifdef FSM_EMISAR_D4_DRIVER -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * eswitch -|2 7|- - * AUX LED -|3 6|- PWM (FET) - * GND -|4 5|- PWM (1x7135) - * ---- - */ +#if 0 // placeholder -#define PWM_CHANNELS 2 +#elif defined(NANJG_LAYOUT) +#include "hwdef-nanjg.h" -#define AUXLED_PIN PB4 // pin 3 +#elif defined(FET_7135_LAYOUT) +#include "hwdef-FET_7135.h" -#define SWITCH_PIN PB3 // pin 2 -#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt +#elif defined(TRIPLEDOWN_LAYOUT) +#include "hwdef-Tripledown.h" -#define PWM1_PIN PB0 // pin 5, 1x7135 PWM -#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 -#define PWM2_PIN PB1 // pin 6, FET PWM -#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 +#elif defined(FERRERO_ROCHER_LAYOUT) +#include "hwdef-Ferrero_Rocher.h" -// (FIXME: remove? not used?) -#define VOLTAGE_PIN PB2 // pin 7, voltage ADC -#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 +#elif defined(FSM_BLF_GT_DRIVER) +#include "hwdef-BLF_GT.h" -//#define TEMP_DIDR ADC4D -#define TEMP_CHANNEL 0b00001111 +#elif defined(FSM_BLF_Q8_DRIVER) +#include "hwdef-BLF_Q8.h" -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels +#elif defined(FSM_EMISAR_D4_DRIVER) +#include "hwdef-Emisar_D4.h" -#endif // ifdef FSM_EMISAR_D4_DRIVER +#elif defined(FSM_EMISAR_D4S_DRIVER) +#include "hwdef-Emisar_D4S.h" +#elif defined(FSM_FW3A_DRIVER) +#include "hwdef-FW3A.h" -#ifdef FSM_FW3A_DRIVER -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * eswitch -|2 7|- optic nerve - * FET -|3 6|- 7x7135 - * GND -|4 5|- 1x7135 - * ---- - */ - -#define PWM_CHANNELS 3 - -#define SWITCH_PIN PB3 // pin 2 -#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt - -#define PWM1_PIN PB0 // pin 5, 1x7135 PWM -#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 -#define PWM2_PIN PB1 // pin 6, FET PWM -#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 -#define PWM3_PIN PB4 // pin 3 -#define PWM3_LVL OCR1B - -#define VISION_PIN PB2 // pin 7, optic nerve -#define ADC_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 - -//#define TEMP_DIDR ADC4D -#define TEMP_CHANNEL 0b00001111 - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - -#endif // ifdef FSM_FW3A_DRIVER - - -#ifdef FSM_BLF_GT_DRIVER -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC (unused) - * eswitch -|2 7|- Voltage divider - * AUX LED -|3 6|- Current control (buck level) - * GND -|4 5|- PWM (buck output on/off) - * ---- - */ - -#define PWM_CHANNELS 2 - -#define AUXLED_PIN PB4 // pin 3 - -#define SWITCH_PIN PB3 // pin 2 -#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt - -#define PWM1_PIN PB0 // pin 5, 1x7135 PWM -#define PWM1_LVL OCR0A // OCR0A is the output compare register for PB0 -#define PWM2_PIN PB1 // pin 6, FET PWM -#define PWM2_LVL OCR0B // OCR0B is the output compare register for PB1 - -#define USE_VOLTAGE_DIVIDER // use a voltage divider on pin 7, not VCC -#define VOLTAGE_PIN PB2 // pin 7, voltage ADC -#define VOLTAGE_CHANNEL 0x01 // MUX 01 corresponds with PB2 -// 1.1V reference, left-adjust, ADC1/PB2 -//#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | (1 << ADLAR) | VOLTAGE_CHANNEL) -// 1.1V reference, no left-adjust, ADC1/PB2 -#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | VOLTAGE_CHANNEL) -#define VOLTAGE_ADC_DIDR ADC1D // Digital input disable bit corresponding with PB2 -#define ADC_PRSCL 0x06 // clk/64 +#elif defined(FSM_TKSABER_DRIVER) +#include "hwdef-TK_Saber.h" -// Raw ADC readings at 4.4V and 2.2V (in-between, we assume values form a straight line) -#define ADC_44 184 -#define ADC_22 92 - -#define TEMP_CHANNEL 0b00001111 - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - -#endif // ifdef FSM_BLF_GT_DRIVER - - -#ifdef FSM_TKSABER_DRIVER -#define DRIVER_TYPE_DEFINED -/* - * ---- - * Reset -|1 8|- VCC - * PWM 4 (A) -|2 7|- e-switch - * PWM 3 (G) -|3 6|- PWM 2 (B) - * GND -|4 5|- PWM 1 (R) - * ---- - */ - -#define PWM_CHANNELS 4 -#define PWM1_PIN PB0 // pin 5 -#define PWM1_LVL OCR0A -#define PWM2_PIN PB1 // pin 6 -#define PWM2_LVL OCR0B -#define PWM3_PIN PB4 // pin 3 -#define PWM3_LVL OCR1B -#define PWM4_PIN PB3 // pin 2 -#define PWM4_LVL OCR1A - -#define SWITCH_PIN PB2 // pin 7 -#define SWITCH_PCINT PCINT2 // pin 7 pin change interrupt - -#define ADC_PRSCL 0x06 // clk/64 (no need to be super fast) - -//#define TEMP_DIDR ADC4D -#define TEMP_CHANNEL 0b00001111 - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - -#endif // TKSABER_DRIVER - - -#ifndef DRIVER_TYPE_DEFINED +#else #error Hey, you need to define an I/O pin layout. -#endif + +#endif // no more recognized driver types #endif // TK_ATTINY_H |