diff options
Diffstat (limited to '')
| -rw-r--r-- | hwdef-Sofirn_SP10-Pro.h | 18 | ||||
| -rw-r--r-- | hwdef-thefreeman-lin16dac.h | 2 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-sofirn-sp10-pro.h | 15 | ||||
| -rw-r--r-- | spaghetti-monster/fsm-ramping.c | 39 |
4 files changed, 40 insertions, 34 deletions
diff --git a/hwdef-Sofirn_SP10-Pro.h b/hwdef-Sofirn_SP10-Pro.h index 7d0d7f5..e47131a 100644 --- a/hwdef-Sofirn_SP10-Pro.h +++ b/hwdef-Sofirn_SP10-Pro.h @@ -53,7 +53,7 @@ PA1 : Boost Enable #define LED_ENABLE_PIN PIN1_bp #define LED_ENABLE_PORT PORTA_OUT -#define LED_DISABLE_DELAY 4 +#define LED_OFF_DELAY 4 #define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened #define DUAL_VOLTAGE_FLOOR 21 // for AA/14500 boost drivers, don't indicate low voltage if below this level @@ -122,4 +122,20 @@ inline void hwdef_setup() { } +// set fuses, these carry over to the ELF file but not the HEX file +// we need this for enabling BOD in Active Mode from the factory. +// settings can be verified / dumped from the ELF file using this +// command: avr-objdump -d -S -j .fuse anduril.elf +FUSES = { + .WDTCFG = FUSE_WDTCFG_DEFAULT, /* Watchdog Configuration */ + .BODCFG = FUSE_ACTIVE0_bm, /* BOD Configuration */ + .OSCCFG = FUSE_OSCCFG_DEFAULT, /* Oscillator Configuration */ + .TCD0CFG = FUSE_TCD0CFG_DEFAULT, /* TCD0 Configuration */ + .SYSCFG0 = FUSE_SYSCFG0_DEFAULT, /* System Configuration 0 */ + .SYSCFG1 = FUSE_SYSCFG1_DEFAULT, /* System Configuration 1 */ + .APPEND = FUSE_APPEND_DEFAULT, /* Application Code Section End */ + .BOOTEND = FUSE_BOOTEND_DEFAULT, /* Boot Section End */ +}; + + #endif diff --git a/hwdef-thefreeman-lin16dac.h b/hwdef-thefreeman-lin16dac.h index adb7886..9d6b145 100644 --- a/hwdef-thefreeman-lin16dac.h +++ b/hwdef-thefreeman-lin16dac.h @@ -47,7 +47,7 @@ Read voltage from VCC pin, has PFET so no drop // For turning on and off the op-amp #define LED2_ENABLE_PIN PIN7_bp #define LED2_ENABLE_PORT PORTA_OUT -#define LED2_ENABLE_DELAY 80 // how many ms to delay turning on the lights after enabling the channel +#define LED2_ON_DELAY 80 // how many ms to delay turning on the lights after enabling the channel // average drop across diode on this hardware #ifndef VOLTAGE_FUDGE_FACTOR diff --git a/spaghetti-monster/anduril/cfg-sofirn-sp10-pro.h b/spaghetti-monster/anduril/cfg-sofirn-sp10-pro.h index a3463ae..bcfc80e 100644 --- a/spaghetti-monster/anduril/cfg-sofirn-sp10-pro.h +++ b/spaghetti-monster/anduril/cfg-sofirn-sp10-pro.h @@ -71,18 +71,3 @@ // enable factory reset on 13H without loosening tailcap #define USE_SOFT_FACTORY_RESET - -// set fuses, these carry over to the ELF file but not the HEX file -// we need this for enabling BOD in Active Mode from the factory. -// settings can be verified / dumped from the ELF file using this -// command: avr-objdump -d -S -j .fuse anduril.elf -FUSES = { - .WDTCFG = FUSE_WDTCFG_DEFAULT, /* Watchdog Configuration */ - .BODCFG = FUSE_ACTIVE0_bm, /* BOD Configuration */ - .OSCCFG = FUSE_OSCCFG_DEFAULT, /* Oscillator Configuration */ - .TCD0CFG = FUSE_TCD0CFG_DEFAULT, /* TCD0 Configuration */ - .SYSCFG0 = FUSE_SYSCFG0_DEFAULT, /* System Configuration 0 */ - .SYSCFG1 = FUSE_SYSCFG1_DEFAULT, /* System Configuration 1 */ - .APPEND = FUSE_APPEND_DEFAULT, /* Application Code Section End */ - .BOOTEND = FUSE_BOOTEND_DEFAULT, /* Boot Section End */ -};
\ No newline at end of file diff --git a/spaghetti-monster/fsm-ramping.c b/spaghetti-monster/fsm-ramping.c index 2e6901d..ade49b7 100644 --- a/spaghetti-monster/fsm-ramping.c +++ b/spaghetti-monster/fsm-ramping.c @@ -93,9 +93,10 @@ void set_level(uint8_t level) { TINT1_LVL = 0; TINT2_LVL = 0; #endif - // for drivers with a slow regulator chip (eg, boost converter, delay before turning off to prevent flashes - #ifdef LED_DISABLE_DELAY - delay_4ms(LED_DISABLE_DELAY/4); + #ifdef LED_OFF_DELAY + // for drivers with a slow regulator chip (eg, boost converter), + // delay before turning off to prevent flashes + delay_4ms(LED_OFF_DELAY/4); #endif // disable the power channel, if relevant #ifdef LED_ENABLE_PIN @@ -108,10 +109,10 @@ void set_level(uint8_t level) { // enable the power channel, if relevant #ifndef USE_TINT_RAMPING // update_tint handles this better #ifdef LED_ENABLE_PIN - #ifdef LED_ENABLE_DELAY + #ifdef LED_ON_DELAY uint8_t led_enable_port_save = LED_ENABLE_PORT; #endif - + #ifndef LED_ENABLE_PIN_LEVEL_MIN LED_ENABLE_PORT |= (1 << LED_ENABLE_PIN); #else @@ -122,24 +123,28 @@ void set_level(uint8_t level) { else // disable during other parts of the ramp LED_ENABLE_PORT &= ~(1 << LED_ENABLE_PIN); #endif - - // for drivers with a slow regulator chip (eg, boost converter, delay before lighting up to prevent flashes - #ifdef LED_ENABLE_DELAY - if (LED_ENABLE_PORT != led_enable_port_save) // only delay if the pin status changed - delay_4ms(LED_ENABLE_DELAY/4); + + // for drivers with a slow regulator chip (eg, boost converter), + // delay before lighting up to prevent flashes + #ifdef LED_ON_DELAY + // only delay if the pin status changed + if (LED_ENABLE_PORT != led_enable_port_save) + delay_4ms(LED_ON_DELAY/4); #endif #endif #ifdef LED2_ENABLE_PIN - #ifdef LED2_ENABLE_DELAY + #ifdef LED2_ON_DELAY uint8_t led2_enable_port_save = LED2_ENABLE_PORT; #endif - + LED2_ENABLE_PORT |= (1 << LED2_ENABLE_PIN); - - // for drivers with a slow regulator chip (eg, boost converter, delay before lighting up to prevent flashes - #ifdef LED2_ENABLE_DELAY - if (LED2_ENABLE_PORT != led2_enable_port_save) // only delay if the pin status changed - delay_4ms(LED2_ENABLE_DELAY/4); + + // for drivers with a slow regulator chip (eg, boost converter), + // delay before lighting up to prevent flashes + #ifdef LED2_ON_DELAY + // only delay if the pin status changed + if (LED2_ENABLE_PORT != led2_enable_port_save) + delay_4ms(LED2_ON_DELAY/4); #endif #endif #endif // ifndef USE_TINT_RAMPING |