diff options
| -rw-r--r-- | hw/lumintop/fw3x-lume1/anduril.h | 27 | ||||
| -rw-r--r-- | hw/lumintop/fw3x-lume1/hwdef.h | 15 |
2 files changed, 29 insertions, 13 deletions
diff --git a/hw/lumintop/fw3x-lume1/anduril.h b/hw/lumintop/fw3x-lume1/anduril.h index b208fbc..5cde5e9 100644 --- a/hw/lumintop/fw3x-lume1/anduril.h +++ b/hw/lumintop/fw3x-lume1/anduril.h @@ -11,7 +11,7 @@ * - 85: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-2586-AVR-8-bit-Microcontroller-ATtiny25-ATtiny45-ATtiny85_Datasheet.pdf */ -#include "lumintop/fw3x-lume1/hwdef.h" +#define HWDEF_H lumintop/fw3x-lume1/hwdef.h // set this light for 50C thermal ceiling #undef DEFAULT_THERM_CEIL @@ -46,11 +46,6 @@ #undef USE_DYNAMIC_UNDERCLOCKING #endif -// the entire ramp is regulated except turbo; don't blink halfway up -#ifdef BLINK_AT_RAMP_MIDDLE -#undef BLINK_AT_RAMP_MIDDLE -#endif - #define RAMP_SMOOTH_FLOOR 1 #define RAMP_SMOOTH_CEIL 149 // turn on BuckBoost from level 1 to 149, but not 150 @@ -59,21 +54,39 @@ #define LED_ENABLE_PIN_LEVEL_MAX 149 // 10 33 56 79 102 125 [149] #define RAMP_DISCRETE_FLOOR 10 -#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL +#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL #define RAMP_DISCRETE_STEPS 7 #define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR #define SIMPLE_UI_CEIL 120 #define SIMPLE_UI_STEPS 5 +// show each channel while it scroll by in the menu +#define USE_CONFIG_COLORS + +// blink numbers on the main LEDs by default (but allow user to change it) +#define DEFAULT_BLINK_CHANNEL CM_MAIN + // slow down party strobe; this driver can't pulse for too short a time #define PARTY_STROBE_ONTIME 4 +// use aux red + aux blue for police strobe +#define USE_POLICE_COLOR_STROBE_MODE +#define POLICE_STROBE_USES_AUX +#define POLICE_COLOR_STROBE_CH1 CM_AUXRED +#define POLICE_COLOR_STROBE_CH2 CM_AUXBLU + // stop panicking at ~85% regulated power or ~750 lm #define THERM_FASTER_LEVEL 140 #define THERM_CAL_OFFSET 0 // not needed due to external sensor +// don't blink while ramping +#ifdef BLINK_AT_RAMP_MIDDLE +#undef BLINK_AT_RAMP_MIDDLE +#endif + + // can't reset the normal way because power is connected before the button #define USE_SOFT_FACTORY_RESET diff --git a/hw/lumintop/fw3x-lume1/hwdef.h b/hw/lumintop/fw3x-lume1/hwdef.h index ca412cc..e50d8b1 100644 --- a/hw/lumintop/fw3x-lume1/hwdef.h +++ b/hw/lumintop/fw3x-lume1/hwdef.h @@ -8,9 +8,9 @@ * * Pin / Name / Function in Lume1 Rev B * 1 PA6 Regulated PWM (PWM1B) - * 2 PA5 R: red aux LED (PWM0B) + * 2 PA5 B: blue aux LED (PWM0B) * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED + * 4 PA3 R: red aux LED * 5 PA2 e-switch (PCINT2) * 6 PA1 Jumper 1 * 7 PA0 Jumper 2 @@ -111,16 +111,19 @@ enum CHANNEL_MODES { #define ADMUX_VOLTAGE_DIVIDER 0b00000101 #define ADC_PRSCL 0x06 // clk/64 +#undef voltage_raw2cooked +#define voltage_raw2cooked mcu_vdivider_raw2cooked + // Raw ADC readings at 4.4V and 2.2V // calibrate the voltage readout here // estimated / calculated values are: // [(Vbatt)*(R2/(R2+R1)) / 2.5V] * 1023 // R1 = R2 = 100kR #ifndef ADC_44 -#define ADC_44 900 +#define ADC_44 (4*900) #endif #ifndef ADC_22 -#define ADC_22 450 +#define ADC_22 (4*450) #endif // Default ADMUX_THERM for Temperature is: 0b10001110 in arch/mcu.h @@ -139,9 +142,9 @@ enum CHANNEL_MODES { #define EXTERN_TEMP_FORMULA(m) (((m)-205)/4.09) // this driver allows for aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 +#define AUXLED_R_PIN PA3 // pin 2 #define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 +#define AUXLED_B_PIN PA5 // pin 4 #define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC #define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC #define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC |