diff options
| -rw-r--r-- | hwdef-Noctigon_DM11-SBT90.h | 154 | ||||
| -rw-r--r-- | hwdef-Noctigon_DM11.h | 13 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-noctigon-dm11-sbt90.h | 73 |
3 files changed, 229 insertions, 11 deletions
diff --git a/hwdef-Noctigon_DM11-SBT90.h b/hwdef-Noctigon_DM11-SBT90.h new file mode 100644 index 0000000..64ebe05 --- /dev/null +++ b/hwdef-Noctigon_DM11-SBT90.h @@ -0,0 +1,154 @@ +#ifndef HWDEF_NOCTIGON_DM11SBT90_H +#define HWDEF_NOCTIGON_DM11SBT90_H + +/* Noctigon DM11-SBT90.2 driver layout (attiny1634) + * (based on Noctigon K1 and DM11) + * + * Pin / Name / Function + * 1 PA6 FET PWM (direct drive) (PWM1B) + * 2 PA5 R: red aux LED (PWM0B) + * 3 PA4 G: green aux LED + * 4 PA3 B: blue aux LED + * 5 PA2 L: button LED + * 6 PA1 (none) + * 7 PA0 (none) + * 8 GND GND + * 9 VCC VCC + * 10 PC5 (none) + * 11 PC4 (none) + * 12 PC3 RESET + * 13 PC2 (none) + * 14 PC1 SCK + * 15 PC0 (none) PWM0A + * 16 PB3 main LED PWM (PWM1A) + * 17 PB2 MISO / e-switch (PCINT10) + * 18 PB1 MOSI / battery voltage (ADC6) + * 19 PB0 Opamp power + * 20 PA7 (none) (PCINT7) + * ADC12 thermal sensor + * + * Main LED power uses one pin to turn the Opamp on/off, + * and one pin to control Opamp power level. + * Linear brightness control uses the power level pin, with dynamic PWM. + * The on/off pin is only used to turn the main LED on and off, + * not to change brightness. + * Also has a direct-drive FET for turbo. + */ + +#ifdef ATTINY +#undef ATTINY +#endif +#define ATTINY 1634 +#include <avr/io.h> + +#define PWM_CHANNELS 2 // override this for the no-FET version +#define PWM_BITS 16 // data type needs 16 bits, not 8 +#define PWM_TOP 255 // highest value used in top half of ramp +#define USE_DYN_PWM // dynamic frequency and speed + +#define SWITCH_PIN PB2 // pin 17 +#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt +#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] +#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] +#define SWITCH_PORT PINB // PINA or PINB or PINC +#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] + +#define PWM1_PIN PB3 // pin 16, Opamp reference +#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 +#define PWM1_CNT TCNT1 // for dynamic PWM, reset phase + +#define PWM2_PIN PA6 // pin 1, DD FET PWM +#define PWM2_LVL OCR1B // OCR1B is the output compare register for PA6 + +// PWM parameters of both channels are tied together because they share a counter +#define PWM1_TOP ICR1 // holds the TOP value for for variable-resolution PWM + +#define LED_ENABLE_PIN PB0 // pin 19, Opamp power +#define LED_ENABLE_PORT PORTB // control port for PB0 + + +#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened +#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 +// pin to ADC mappings are in DS table 19-4 +#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 +// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 +#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D +// DS tables 19-3, 19-4 +// Bit 7 6 5 4 3 2 1 0 +// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 +// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 +// divided by ... +// REFS[1:0] = 1, 0 for internal 1.1V reference +// other bits reserved +#define ADMUX_VOLTAGE_DIVIDER 0b10000110 +#define ADC_PRSCL 0x07 // clk/128 + +// Raw ADC readings at 4.4V and 2.2V +// calibrate the voltage readout here +// estimated / calculated values are: +// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) +// D1, R1, R2 = 0, 330, 100 +#ifndef ADC_44 +//#define ADC_44 981 // raw value at 4.40V +#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 +#endif +#ifndef ADC_22 +//#define ADC_22 489 // raw value at 2.20V +#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 +#endif + +// this light has aux LEDs under the optic +#define AUXLED_R_PIN PA5 // pin 2 +#define AUXLED_G_PIN PA4 // pin 3 +#define AUXLED_B_PIN PA3 // pin 4 +#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC +#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC +#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC + +#define BUTTON_LED_PIN PA2 // pin 5 +#define BUTTON_LED_PORT PORTA // for all "PA" pins +#define BUTTON_LED_DDR DDRA // for all "PA" pins +#define BUTTON_LED_PUE PUEA // for all "PA" pins + +// with so many pins, doing this all with #ifdefs gets awkward... +// ... so just hardcode it in each hwdef file instead +inline void hwdef_setup() { + // enable output ports + // Opamp level and Opamp on/off + DDRB = (1 << PWM1_PIN) + | (1 << LED_ENABLE_PIN); + // DD FET PWM, aux R/G/B, button LED + DDRA = (1 << PWM2_PIN) + | (1 << AUXLED_R_PIN) + | (1 << AUXLED_G_PIN) + | (1 << AUXLED_B_PIN) + | (1 << BUTTON_LED_PIN) + ; + + // configure PWM + // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter + // pre-scale for timer: N = 1 + // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) + // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) + // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) + // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) + TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) + | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) + | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) + ; + TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) + | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) + ; + + // set PWM resolution + PWM1_TOP = PWM_TOP; + + // set up e-switch + //PORTB = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? + PUEB = (1 << SWITCH_PIN); // pull-up for e-switch + SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt +} + +#define LAYOUT_DEFINED + +#endif diff --git a/hwdef-Noctigon_DM11.h b/hwdef-Noctigon_DM11.h index 93ed707..19532e9 100644 --- a/hwdef-Noctigon_DM11.h +++ b/hwdef-Noctigon_DM11.h @@ -21,10 +21,10 @@ * 14 PC1 SCK * 15 PC0 (none) PWM0A * 16 PB3 main LED PWM (PWM1A) - * 17 PB2 MISO / e-switch? (PCINT10) + * 17 PB2 MISO / (none) (PCINT10) * 18 PB1 MOSI / battery voltage (ADC6) * 19 PB0 Opamp power - * 20 PA7 e-switch? (PCINT7) + * 20 PA7 e-switch (PCINT7) * ADC12 thermal sensor * * Main LED power uses one pin to turn the Opamp on/off, @@ -46,13 +46,6 @@ #define PWM_TOP 255 // highest value used in top half of ramp #define USE_DYN_PWM // dynamic frequency and speed -//#define SWITCH_PIN PB2 // pin 17 -//#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt -//#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] -//#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] -//#define SWITCH_PORT PINB // PINA or PINB or PINC -//#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] - #define SWITCH_PIN PA7 // pin 20 #define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt #define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] @@ -150,8 +143,6 @@ inline void hwdef_setup() { PWM1_TOP = PWM_TOP; // set up e-switch - ////PORTB = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? - //PUEB = (1 << SWITCH_PIN); // pull-up for e-switch //PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? PUEA = (1 << SWITCH_PIN); // pull-up for e-switch SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt diff --git a/spaghetti-monster/anduril/cfg-noctigon-dm11-sbt90.h b/spaghetti-monster/anduril/cfg-noctigon-dm11-sbt90.h new file mode 100644 index 0000000..7e671d6 --- /dev/null +++ b/spaghetti-monster/anduril/cfg-noctigon-dm11-sbt90.h @@ -0,0 +1,73 @@ +// Noctigon DM11-SBT90.2 config options for Anduril +#define MODEL_NUMBER "0273" +#include "hwdef-Noctigon_DM11-SBT90.h" +#include "hank-cfg.h" +// ATTINY: 1634 + +// this light has three aux LED channels: R, G, B +#define USE_AUX_RGB_LEDS +// ... and a single LED in the button +#define USE_BUTTON_LED +// don't use aux LEDs while main LED is on +#ifdef USE_INDICATOR_LED_WHILE_RAMPING +#undef USE_INDICATOR_LED_WHILE_RAMPING +#endif + + +// power channels: +// - linear: 5A? +// - FET: DD +#define RAMP_LENGTH 150 +#define USE_DYN_PWM + +// maxreg at 130, dynamic PWM: level_calc.py 5.01 2 149 7135 1 0.3 1740 FET 1 10 3190 --pwm dyn:64:16384:255 +// (plus one extra level at the beginning for moon) +#define PWM1_LEVELS 0,1,1,2,2,3,4,5,6,7,8,9,11,12,14,16,17,19,22,24,26,29,31,34,37,40,43,46,49,53,56,60,63,67,71,74,78,82,86,89,93,96,99,103,105,108,110,112,114,115,116,116,115,114,112,109,106,101,95,89,81,71,60,48,34,19,20,21,22,23,24,26,27,28,30,31,32,34,36,37,39,41,43,45,47,49,51,53,56,58,61,63,66,69,72,75,78,81,84,88,91,95,99,103,107,111,115,119,124,129,133,138,143,149,154,159,165,171,177,183,189,196,203,210,217,224,231,239,247,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0 +#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,9,20,30,41,52,63,75,87,99,112,125,138,151,165,179,194,208,224,239,255 +#define PWM_TOPS 16383,16383,11750,14690,9183,12439,13615,13955,13877,13560,13093,12529,13291,12513,12756,12769,11893,11747,12085,11725,11329,11316,10851,10713,10518,10282,10016,9729,9428,9298,8971,8794,8459,8257,8043,7715,7497,7275,7052,6753,6538,6260,5994,5798,5501,5271,5006,4758,4525,4268,4030,3775,3508,3263,3010,2752,2517,2256,1998,1763,1512,1249,994,749,497,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255 + +#define DEFAULT_LEVEL 70 +#define MAX_1x7135 130 +#define HALFSPEED_LEVEL 12 +#define QUARTERSPEED_LEVEL 4 + +// don't blink halfway up +#ifdef BLINK_AT_RAMP_MIDDLE +#undef BLINK_AT_RAMP_MIDDLE +#endif + +#define RAMP_SMOOTH_FLOOR 10 // low levels may be unreliable +#define RAMP_SMOOTH_CEIL 130 +// 10, 30, 50, [70], 90, 110, 130 +#define RAMP_DISCRETE_FLOOR 10 +#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL +#define RAMP_DISCRETE_STEPS 7 + +// safe limit ~75% power +#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR +#define SIMPLE_UI_CEIL RAMP_DISCRETE_CEIL +#define SIMPLE_UI_STEPS 5 + +// make candle mode wobble more +#define CANDLE_AMPLITUDE 30 + +// stop panicking at ~70% power or ~600 lm +#define THERM_FASTER_LEVEL 130 +#define MIN_THERM_STEPDOWN 66 // must be > end of dynamic PWM range + +//#define THERM_RESPONSE_MAGNITUDE 32 // smaller adjustments, this host changes temperature slowly +//#define THERM_NEXT_WARNING_THRESHOLD 32 // more error tolerance before adjusting + +// slow down party strobe; this driver can't pulse for 1ms or less +// (only needed on no-FET build) +//#define PARTY_STROBE_ONTIME 2 + +#define THERM_CAL_OFFSET 5 + +// the power regulator is a bit slow, so push it harder for a quick response from off +#define DEFAULT_JUMP_START_LEVEL 21 +#define BLINK_BRIGHTNESS 50 +#define BLINK_ONCE_TIME 12 + +// added for convenience +#define USE_SOFT_FACTORY_RESET |