3 files changed, 8 insertions, 7 deletions
diff --git a/hw/thefreeman/avr32dd20-devkit/hwdef.c b/hw/thefreeman/avr32dd20-devkit/hwdef.c
index 460082f..5b534d2 100644
--- a/hw/thefreeman/avr32dd20-devkit/hwdef.c
+++ b/hw/thefreeman/avr32dd20-devkit/hwdef.c
@@ -119,13 +119,13 @@ bool gradual_tick_main(uint8_t gt) {
 
 uint8_t voltage_raw2cooked(uint16_t measurement) {
     // In : 65535 * BATTLVL / 1.024V
-    // Out: uint8_t: Vbat * 40
+    // Out: uint8_t: Vbat * 50
     // BATTLVL = Vbat * (100.0/(330+100)) = Vbat / 4.3
-    // So, Out = In * 4.3 / 1600
+    // So, Out = In * 4.3 / 1280
     // (plus a bit of fudging to fix the slope and offset,
     //  based on measuring actual hardware)
     uint8_t result = (uint32_t)(measurement + (65535 * 4 / 1024))
-                     * 43 / 16128;
+                     * 43 / 12880;
     return result;
 }
 
diff --git a/hw/thefreeman/avr32dd20-devkit/hwdef.h b/hw/thefreeman/avr32dd20-devkit/hwdef.h
index 231f74a..5015c24 100644
--- a/hw/thefreeman/avr32dd20-devkit/hwdef.h
+++ b/hw/thefreeman/avr32dd20-devkit/hwdef.h
@@ -109,8 +109,8 @@ enum CHANNEL_MODES {
 // AVR datasheet table 3.1 I/O Multiplexing, PA6 ADC0 = AIN26
 #define USE_VOLTAGE_DIVIDER    // use a dedicated pin, not VCC, because VCC input is regulated
 #define ADMUX_VOLTAGE_DIVIDER  ADC_MUXPOS_AIN26_gc
-#define DUAL_VOLTAGE_FLOOR     (4*21) // for AA/14500 boost drivers, don't indicate low voltage if below this level
-#define DUAL_VOLTAGE_LOW_LOW   (4*7)  // the lower voltage range's danger zone 0.7 volts (NiMH)
+#define DUAL_VOLTAGE_FLOOR     (21*dV)  // for AA/14500 boost drivers, don't indicate low voltage if below this level
+#define DUAL_VOLTAGE_LOW_LOW   ( 7*dV)  // the lower voltage range's danger zone 0.7 volts (NiMH)
 // don't use the default VDD converter
 // convert BATT LVL pin readings to FSM volt units
 #undef voltage_raw2cooked
@@ -155,6 +155,7 @@ inline void hwdef_setup() {
     //PORTA.PIN2CTRL = PORT_PULLUPEN_bm;  // B
     #ifdef USE_BST_BYPASS
     PORTA.PIN3CTRL = PORT_PULLUPEN_bm;  // BBY
+    BST_BYPASS_PORT |= (1 << BST_BYPASS_PIN);
     #endif
     PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
     PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
diff --git a/hw/thefreeman/boost-fwaa-mp3432-hdr-dac-rgb/hwdef.h b/hw/thefreeman/boost-fwaa-mp3432-hdr-dac-rgb/hwdef.h
index bc1d9a7..1c6e6be 100644
--- a/hw/thefreeman/boost-fwaa-mp3432-hdr-dac-rgb/hwdef.h
+++ b/hw/thefreeman/boost-fwaa-mp3432-hdr-dac-rgb/hwdef.h
@@ -94,8 +94,8 @@ enum CHANNEL_MODES {
 // Voltage divider battLVL
 #define USE_VOLTAGE_DIVIDER       // use a dedicated pin, not VCC, because VCC input is regulated
 #define ADMUX_VOLTAGE_DIVIDER  ADC_MUXPOS_AIN2_gc  // which ADC channel to read
-#define DUAL_VOLTAGE_FLOOR     (4*21) // for AA/14500 boost drivers, don't indicate low voltage if below this level
-#define DUAL_VOLTAGE_LOW_LOW   (4*7)  // the lower voltage range's danger zone 0.7 volts (NiMH)
+#define DUAL_VOLTAGE_FLOOR     (21*dV)  // for AA/14500 boost drivers, don't indicate low voltage if below this level
+#define DUAL_VOLTAGE_LOW_LOW   ( 7*dV)  // the lower voltage range's danger zone 0.7 volts (NiMH)
 // don't use the default VDD converter
 #undef voltage_raw2cooked
 #define voltage_raw2cooked  mcu_vdivider_raw2cooked