3 files changed, 50 insertions, 2 deletions
diff --git a/hwdef-Mateminco_MT35-Mini.h b/hwdef-Mateminco_MT35-Mini.h
new file mode 100644
index 0000000..344f658
--- /dev/null
+++ b/hwdef-Mateminco_MT35-Mini.h
@@ -0,0 +1,47 @@
+#ifndef HWDEF_MT35_MINI_H
+#define HWDEF_MT35_MINI_H
+
+/* Mateminco MT35-Mini / Astrolux FT03
+ *           ----
+ *   Reset -|1  8|- VCC
+ * eswitch -|2  7|- Aux LED
+ *  1x7135 -|3  6|- NC
+ *     GND -|4  5|- FET
+ *           ----
+ */
+
+#define PWM_CHANNELS 2
+
+#ifndef SWITCH_PIN
+#define SWITCH_PIN   PB3    // pin 2
+#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
+#endif
+
+#ifndef PWM1_PIN
+#define PWM1_PIN PB4        // pin 3, 1x7135 PWM
+#define PWM1_LVL OCR1B      // OCR1B is the output compare register for PB0
+#endif
+
+#ifndef PWM2_PIN
+#define PWM2_PIN PB0        // pin 5, FET PWM
+#define PWM2_LVL OCR0A      // OCR0A is the output compare register for PB4
+#endif
+
+#define ADC_PRSCL   0x07    // clk/128
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
+#endif
+
+// lighted button
+#ifndef AUXLED_PIN
+#define AUXLED_PIN   PB2    // pin 7
+#endif
+
+#define FAST 0xA3           // fast PWM both channels
+#define PHASE 0xA1          // phase-correct PWM both channels
+
+#define LAYOUT_DEFINED
+
+#endif
diff --git a/hwdef-Sofirn_SP10-Pro.h b/hwdef-Sofirn_SP10-Pro.h
index bb10f2f..7d0d7f5 100644
--- a/hwdef-Sofirn_SP10-Pro.h
+++ b/hwdef-Sofirn_SP10-Pro.h
@@ -53,9 +53,10 @@ PA1 : Boost Enable
 
 #define LED_ENABLE_PIN   PIN1_bp
 #define LED_ENABLE_PORT  PORTA_OUT
+#define LED_DISABLE_DELAY 4
 
 #define USE_VOLTAGE_DIVIDER       // use a dedicated pin, not VCC, because VCC input is flattened
-#define DUAL_VOLTAGE_FLOOR    20  // for AA/14500 boost drivers, don't indicate low voltage if below this level
+#define DUAL_VOLTAGE_FLOOR    21  // for AA/14500 boost drivers, don't indicate low voltage if below this level
 #define DUAL_VOLTAGE_LOW_LOW   7  // the lower voltage range's danger zone 0.7 volts (NiMH)
 #define ADMUX_VOLTAGE_DIVIDER ADC_MUXPOS_AIN9_gc  // which ADC channel to read
 
diff --git a/hwdef-thefreeman-lin16dac.h b/hwdef-thefreeman-lin16dac.h
index 0999c4c..adb7886 100644
--- a/hwdef-thefreeman-lin16dac.h
+++ b/hwdef-thefreeman-lin16dac.h
@@ -47,7 +47,7 @@ Read voltage from VCC pin, has PFET so no drop
 // For turning on and off the op-amp
 #define LED2_ENABLE_PIN   PIN7_bp
 #define LED2_ENABLE_PORT  PORTA_OUT
-
+#define LED2_ENABLE_DELAY 80  // how many ms to delay turning on the lights after enabling the channel
 
 // average drop across diode on this hardware
 #ifndef VOLTAGE_FUDGE_FACTOR