2 files changed, 93 insertions, 48 deletions
diff --git a/hwdef-Mateminco_MT35-Mini.h b/hwdef-Mateminco_MT35-Mini.h
deleted file mode 100644
index 995a514..0000000
--- a/hwdef-Mateminco_MT35-Mini.h
+++ /dev/null
@@ -1,48 +0,0 @@
-// Mateminco MT35-Mini / Astrolux FT03
-// Copyright (C) 2022-2023 (FIXME)
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- *           ----
- *   Reset -|1  8|- VCC
- * eswitch -|2  7|- Aux LED
- *  1x7135 -|3  6|- NC
- *     GND -|4  5|- FET
- *           ----
- */
-
-#define PWM_CHANNELS 2
-
-#ifndef SWITCH_PIN
-#define SWITCH_PIN   PB3    // pin 2
-#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
-#endif
-
-#ifndef PWM1_PIN
-#define PWM1_PIN PB4        // pin 3, 1x7135 PWM
-#define PWM1_LVL OCR1B      // OCR1B is the output compare register for PB0
-#endif
-
-#ifndef PWM2_PIN
-#define PWM2_PIN PB0        // pin 5, FET PWM
-#define PWM2_LVL OCR0A      // OCR0A is the output compare register for PB4
-#endif
-
-#define ADC_PRSCL   0x07    // clk/128
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-// lighted button
-#ifndef AUXLED_PIN
-#define AUXLED_PIN   PB2    // pin 7
-#endif
-
-#define FAST 0xA3           // fast PWM both channels
-#define PHASE 0xA1          // phase-correct PWM both channels
-
-#define LAYOUT_DEFINED
-
diff --git a/hwdef-mateminco-mt35-mini.h b/hwdef-mateminco-mt35-mini.h
new file mode 100644
index 0000000..015c813
--- /dev/null
+++ b/hwdef-mateminco-mt35-mini.h
@@ -0,0 +1,93 @@
+// Mateminco MT35-Mini / Astrolux FT03
+// Copyright (C) 2022-2023 (original author TBD), Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/*
+ *           ----
+ *   Reset -|1  8|- VCC
+ * eswitch -|2  7|- Aux LED
+ *  1x7135 -|3  6|- NC
+ *     GND -|4  5|- FET
+ *           ----
+ */
+
+#define ATTINY 85
+#include <avr/io.h>
+
+#define HWDEF_C_FILE hwdef-emisar-d4.c
+
+// channel modes
+// * 0. FET+7135 stacked
+#define NUM_CHANNEL_MODES  1
+enum CHANNEL_MODES {
+    CM_MAIN = 0,
+};
+
+#define DEFAULT_CHANNEL_MODE  CM_MAIN
+
+// right-most bit first, modes are in fedcba9876543210 order
+#define CHANNEL_MODES_ENABLED 0b00000001
+
+
+#define PWM_CHANNELS 2  // old, remove this
+
+#define PWM_BITS      8       // attiny85 only supports up to 8 bits
+#define PWM_GET       PWM_GET8
+#define PWM_DATATYPE  uint8_t
+#define PWM_DATATYPE2 uint16_t
+#define PWM1_DATATYPE uint8_t   // little FET ramp
+#define PWM2_DATATYPE uint8_t   // big FET ramp
+
+#define PWM_TOP_INIT  255    // highest value used in top half of ramp
+
+// 1x7135 channel
+#define CH1_PIN  PB4        // pin 3, 1x7135 PWM
+#define CH1_PWM  OCR1B      // OCR1B is the output compare register for PB4
+
+// DD FET channel
+#define CH2_PIN  PB0        // pin 5, FET PWM
+#define CH2_PWM  OCR0A      // OCR0A is the output compare register for PB0
+
+// lighted button
+#define AUXLED_PIN   PB2    // pin 7
+
+// e-switch
+#ifndef SWITCH_PIN
+#define SWITCH_PIN   PB3    // pin 2
+#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
+#endif
+
+#define ADC_PRSCL   0x07    // clk/128
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
+#endif
+
+#define FAST 0xA3           // fast PWM both channels
+#define PHASE 0xA1          // phase-correct PWM both channels
+
+
+inline void hwdef_setup() {
+    // configure PWM channels
+    DDRB = (1 << CH1_PIN)
+         | (1 << CH2_PIN);
+
+    // configure PWM channels
+    TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
+    TCCR0A = PHASE;
+
+    // Second PWM counter is ... weird
+    TCCR1 = _BV (CS10);
+    GTCCR = _BV (COM1B1) | _BV (PWM1B);
+    OCR1C = PWM_TOP_INIT;  // Set ceiling value to maximum
+
+    // configure e-switch
+    PORTB = (1 << SWITCH_PIN);  // e-switch is the only input
+    PCMSK = (1 << SWITCH_PIN);  // pin change interrupt uses this pin
+}
+
+
+#define LAYOUT_DEFINED
+