1 files changed, 0 insertions, 114 deletions
diff --git a/hwdef-blf-lt1.h b/hwdef-blf-lt1.h
deleted file mode 100644
index b113fd4..0000000
--- a/hwdef-blf-lt1.h
+++ /dev/null
@@ -1,114 +0,0 @@
-// BLF LT1 driver layout
-// Copyright (C) 2018-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- *           ----
- *   Reset -|1  8|- VCC
- * eswitch -|2  7|- (unused)
- * aux LED -|3  6|- PWM (5000K)
- *     GND -|4  5|- PWM (3000K)
- *           ----
- */
-
-#define ATTINY 85
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hwdef-blf-lt1.c
-
-// channel modes:
-// * 0. channel 1 only
-// * 1. channel 2 only
-// * 2. both channels, tied together, max "200%" power
-// * 3. both channels, manual blend, max "100%" power
-// * 4. both channels, auto blend, reversible
-#define NUM_CHANNEL_MODES   5
-enum channel_modes_e {
-    CM_CH1 = 0,
-    CM_CH2,
-    CM_BOTH,
-    CM_BLEND,
-    CM_AUTO,
-};
-
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b00011000
-#define USE_CHANNEL_MODE_ARGS
-// _, _, _, 128=middle CCT, 0=warm-to-cool
-#define CHANNEL_MODE_ARGS     0,0,0,128,0
-
-// can use some of the common handlers
-#define USE_CALC_2CH_BLEND
-
-
-#define PWM_CHANNELS   1  // old, remove this
-
-#define PWM_BITS      16  // 8-bit hardware PWM + 16-bit DSM
-
-#define PWM_GET       PWM_GET16
-#define PWM_DATATYPE  uint16_t
-#define PWM_DATATYPE2 uint32_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint16_t  // 15-bit PWM+DSM ramp
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM_TOP_INIT  255
-#define DSM_TOP       (255<<7) // 15-bit resolution leaves 1 bit for carry
-
-// timer interrupt for DSM
-#define DSM_vect     TIMER0_OVF_vect
-#define DSM_INTCTRL  TIMSK
-#define DSM_OVF_bm   (1<<TOIE0)
-
-#define DELAY_FACTOR 90  // less time in delay() because more time spent in interrupts
-
-// warm LEDs
-uint16_t ch1_dsm_lvl;
-uint8_t ch1_pwm, ch1_dsm;
-#define CH1_PIN  PB1        // pin 6, warm tint PWM
-#define CH1_PWM  OCR0B      // OCR0B is the output compare register for PB1
-
-// cold LEDs
-uint16_t ch2_dsm_lvl;
-uint8_t ch2_pwm, ch2_dsm;
-#define CH2_PIN  PB0        // pin 5, cold tint PWM
-#define CH2_PWM  OCR0A      // OCR0A is the output compare register for PB0
-
-// lighted button
-#define AUXLED_PIN   PB4    // pin 3
-
-// e-switch
-#define SWITCH_PIN   PB3    // pin 2
-#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
-
-#define ADC_PRSCL   0x07    // clk/128
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-#define FAST 0xA3           // fast PWM both channels
-#define PHASE 0xA1          // phase-correct PWM both channels
-
-
-inline void hwdef_setup() {
-    // configure PWM channels
-    DDRB = (1 << CH1_PIN)
-         | (1 << CH2_PIN);
-
-    TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
-    TCCR0A = PHASE;
-
-    // enable timer overflow interrupt for DSM purposes
-    //DSM_INTCTRL |= DSM_OVF_bm;  // moved to hwdef.c functions instead
-
-    // configure e-switch
-    PORTB = (1 << SWITCH_PIN);  // e-switch is the only input
-    PCMSK = (1 << SWITCH_PIN);  // pin change interrupt uses this pin
-}
-
-
-#define LAYOUT_DEFINED
-