diff options
Diffstat (limited to 'spaghetti-monster')
| -rw-r--r-- | spaghetti-monster/anduril/cfg-fw3x-lume1.h | 22 |
1 files changed, 6 insertions, 16 deletions
diff --git a/spaghetti-monster/anduril/cfg-fw3x-lume1.h b/spaghetti-monster/anduril/cfg-fw3x-lume1.h index 280c433..184ab8e 100644 --- a/spaghetti-monster/anduril/cfg-fw3x-lume1.h +++ b/spaghetti-monster/anduril/cfg-fw3x-lume1.h @@ -1,5 +1,5 @@ // lume1 for FW3x config options for Anduril -// Copyright (C) 2020-2023 (FIXME) +// Copyright (C) 2020-2023 LoneOceans, Selene ToyKeeper // SPDX-License-Identifier: GPL-3.0-or-later #pragma once @@ -11,10 +11,7 @@ * - 85: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-2586-AVR-8-bit-Microcontroller-ATtiny25-ATtiny45-ATtiny85_Datasheet.pdf */ -// TODO: determine if "03" (Lumintop) is the right prefix, -// or if there should be a brand ID for LoneOceans #define MODEL_NUMBER "0314" - #include "hwdef-fw3x-lume1.h" // ATTINY: 1634 @@ -36,7 +33,7 @@ // ../../bin/level_calc.py cube 1 149 7135 0 0.5 1000, with 0 appended to the end. // for FET PWM (PWM2), all values are 0, except for last value of 1023 // (with max_pwm set to 1023) -#define RAMP_LENGTH 150 +#define RAMP_SIZE 150 //#define PWM1_LEVELS 0,0,0,0,1,1,1,1,2,2,2,3,3,4,4,5,5,6,7,7,8,9,10,11,12,13,14,15,16,17,19,20,22,23,25,26,28,30,32,34,36,38,40,42,45,47,49,52,55,58,60,63,66,70,73,76,80,83,87,91,94,98,102,107,111,115,120,124,129,134,139,144,150,155,160,166,172,178,184,190,196,203,209,216,223,230,237,244,252,259,267,275,283,291,299,308,316,325,334,343,353,362,372,382,392,402,412,423,433,444,455,466,478,489,501,513,525,538,550,563,576,589,602,616,630,644,658,672,687,701,716,731,747,762,778,794,810,827,844,861,878,895,913,930,948,967,985,1004,1023,0 #define PWM1_LEVELS 1,1,1,1,2,2,2,2,3,3,3,4,4,5,5,6,6,7,8,8,9,10,11,12,13,14,15,16,17,18,20,21,23,24,26,27,29,31,33,35,37,39,41,43,45,48,50,53,56,58,61,64,67,70,74,77,80,84,88,91,95,99,103,108,112,116,121,125,130,135,140,145,150,156,161,167,173,178,184,191,197,203,210,217,223,230,238,245,252,260,268,275,283,292,300,308,317,326,335,344,353,363,372,382,392,402,413,423,434,445,456,467,478,490,502,514,526,538,551,563,576,589,603,616,630,644,658,672,687,702,717,732,747,763,778,794,811,827,844,861,878,895,913,931,949,967,985,1004,1023,0 #define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1023 @@ -67,25 +64,18 @@ #define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL #define RAMP_DISCRETE_STEPS 7 -// Muggle mode: Goal from about ~10 lumens to about ~300+ lumens -// In this case, ramp number 99 is about 1A to the driver -#define MUGGLE_FLOOR RAMP_DISCRETE_FLOOR -#define MUGGLE_CEILING 99 +#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR +#define SIMPLE_UI_CEIL 120 +#define SIMPLE_UI_STEPS 5 // slow down party strobe; this driver can't pulse for too short a time #define PARTY_STROBE_ONTIME 4 -// optional, makes initial turbo step-down faster so first peak isn't as hot -// FET mode can run very very hot, so be extra careful -//#define THERM_HARD_TURBO_DROP - // stop panicking at ~85% regulated power or ~750 lm #define THERM_FASTER_LEVEL 140 #define THERM_CAL_OFFSET 0 // not needed due to external sensor -// easier access to thermal config mode, similar to Emisar, Noctigon -#define USE_TENCLICK_THERMAL_CONFIG - // can't reset the normal way because power is connected before the button #define USE_SOFT_FACTORY_RESET + |