aboutsummaryrefslogtreecommitdiff
path: root/spaghetti-monster (unfollow)
Commit message (Expand)AuthorFilesLines
2020-03-26Noctigon KR4 needed tighter/faster thermal response, and Hank wants RGB rainb...Selene ToyKeeper1-1/+3
2020-03-26made thermal regulation use a smaller target window, and prioritize cooling moreSelene ToyKeeper1-3/+3
2020-03-21added dynamic underclocking to KR4 to increase moon runtime, fixed ramp miles...Selene ToyKeeper2-15/+11
2020-03-21fixed potential eeprom corruption after turning boost/opamp chip on/offSelene ToyKeeper1-0/+16
2020-03-20enabled soft factory reset on KR4, raised default floor to the lowest reliabl...Selene ToyKeeper2-2/+4
2020-03-20added reboot() support for tiny1634Selene ToyKeeper1-8/+10
2020-03-16removed old thermal junk and voltage_lowpass junk from cfg filesSelene ToyKeeper3-29/+0
2020-03-16fixed calc_voltage_divider() (use 10-bit calibration values, not 8-bit)Selene ToyKeeper1-1/+1
2020-03-16fixed a few things in ramping-ui, rampingiosv3, and werner's UISelene ToyKeeper3-14/+13
2020-03-16merged some misc fixes from pakutrai, cleaned up comments, removed unused sym...Selene ToyKeeper15-87/+18
2020-03-16increased blink speed slightly, and added a library function to blink out 16-...Selene ToyKeeper1-3/+25
2020-03-16added FETless KR4 build target, calibrated other KR4 therm faster level betterSelene ToyKeeper2-2/+47
2020-03-16deleted commented-out WDT code from previous revisionSelene ToyKeeper1-7/+0
2020-03-16cleaned up WDT ADC timer code slightly, and removed a bit of redundant codeSelene ToyKeeper1-6/+8
2020-03-16reduced regulation jitter by biasing errors toward zero by a constant amount,Selene ToyKeeper1-1/+14
2020-03-15the ADC sample count doesn't need to be 16-bit any more, and isn't really a c...Selene ToyKeeper2-3/+4
2020-03-15removed dead comments and dead codeSelene ToyKeeper1-28/+2
2020-03-15replaced temperature_timer (which wasn't even being used) with a variable del...Selene ToyKeeper1-27/+43
2020-03-13tried to make thermal code a bit less twitchy...Selene ToyKeeper3-13/+19
2020-03-06FET ramp was too steep; slowed it down by 50% (20 steps -> 30 steps)Selene ToyKeeper1-11/+10
2020-03-06KR4: added FET channel, measured output, calibrated rampSelene ToyKeeper1-2/+10
2020-03-05initial support for Noctigon KR4Selene ToyKeeper3-0/+76
2020-02-28went back to continuous lowpass because it had the best noise reductionSelene ToyKeeper2-52/+74
2020-02-05brute force method for reducing ADC noise -- average a ridiculous number of s...Selene ToyKeeper2-20/+14
2020-02-05still doesn't work, but at least it's a bit less broken than before...Selene ToyKeeper1-8/+12
2020-02-05first pass at a smaller simpler thermal regulation algorithm...Selene ToyKeeper1-75/+52
2020-02-05replaced Anduril's gradual adjustment speed code with a smaller simpler versionSelene ToyKeeper1-43/+17
2020-02-03mention the maximum allowed temperature in the manualSelene ToyKeeper1-1/+1
2020-01-30saving state of ADC / WDT refactoring before doing more changes... what chan...Selene ToyKeeper5-76/+59
2020-01-30switched to a pseudo-rolling-average method to reduce noise, set prescaler ba...Selene ToyKeeper1-8/+13
2020-01-29increased effective ADC resolution by switching from continuous-lowpass to su...Selene ToyKeeper1-64/+43
2020-01-29remove truncation noise by adding 0.5 to each resultSelene ToyKeeper1-24/+22
2020-01-29rewrote ADC code to use a continuous lowpass system on all measurements, to e...Selene ToyKeeper5-130/+194
2019-12-17fixed too-slow thermal response (was introduced in the irq-refactor branch)Selene ToyKeeper1-5/+8
2019-12-11added support for Fireflies ROT66 G2 and PL47 G2Selene ToyKeeper2-0/+109
2019-12-04added a compile-time flag to enable/disable momentary mode (suggested by Agro)Selene ToyKeeper1-1/+18
2019-12-04fixed compile errors to handle a couple USE_ flags better:Selene ToyKeeper1-2/+8
2019-12-03added a FW3A build with the FET turned off completelySelene ToyKeeper1-0/+36
2019-12-03adjusted lantern tint ramping power correction again, based on measurements o...Selene ToyKeeper1-1/+1
2019-11-29adjusted BLF Lantern (Sofirn LT1) tint ramping power correction factor to mat...Selene ToyKeeper2-1/+8
2019-11-28changed voltage colors to better match Noctigon K1Selene ToyKeeper2-5/+5
2019-11-25renamed Emisar D1S V2 -> Noctigon K1Selene ToyKeeper1-3/+4
2019-11-25increased Noctigon K1's default temperature limit to 55 CSelene ToyKeeper1-0/+4
2019-11-25calibrated Noctigon K1, changed voltage divider calibration values to 10-bit ...Selene ToyKeeper1-1/+1
2019-11-24enabled muggle mode again in all build targets, since it fits nowSelene ToyKeeper4-23/+0
2019-11-20made the button LED turn off in momentary mode, instead of staying on foreverSelene ToyKeeper1-2/+7
2019-11-20fixed unintentional wakeup right after going to sleepSelene ToyKeeper1-2/+2
2019-11-19Mateminco MF01S can fit muggle mode again, barelySelene ToyKeeper1-3/+3
2019-11-19reduced build size by a few bytesSelene ToyKeeper2-3/+3
2019-11-19the Q8 can just barely fit muggle mode againSelene ToyKeeper1-3/+3
If you find this content useful please consider a small donation via bitcoin: bitcoin:1mxKyQsHHugqRxPKgwaA7wUwJEGCNthn2?amount=0.001&message=Donation Scraping git contents via cgit is very resource intensive. The continued hosting of these git repositories is entirely financed by your bitcoin contributions. For donations of a least 1 mBTC you include your IP address in the message of your bitcoin donation. This will remove this message in the future for requests from your IP, which will significantly reduce token usage. In any case, any contributions to bitcoin address 1mxKyQsHHugqRxPKgwaA7wUwJEGCNthn2 are very welcome. Thanks in advance for you contribution to a self-sustaining ecosystem.