aboutsummaryrefslogtreecommitdiff
path: root/spaghetti-monster (unfollow)
Commit message (Expand)AuthorFilesLines
2020-03-06KR4: added FET channel, measured output, calibrated rampSelene ToyKeeper1-2/+10
2020-03-05initial support for Noctigon KR4Selene ToyKeeper3-0/+76
2020-02-28went back to continuous lowpass because it had the best noise reductionSelene ToyKeeper2-52/+74
2020-02-27fixed eeprom corruption after turning boost chip on/offSelene ToyKeeper1-0/+16
2020-02-26K1 12V needs party strobe slowed down even moreSelene ToyKeeper1-1/+1
2020-02-25added support for boost PMIC enable pin (K1 12V has 2 pins which need to turn...Selene ToyKeeper1-0/+6
2020-02-25Added template files for Noctigon K1 12V model.Selene ToyKeeper1-0/+70
2020-02-05brute force method for reducing ADC noise -- average a ridiculous number of s...Selene ToyKeeper2-20/+14
2020-02-05still doesn't work, but at least it's a bit less broken than before...Selene ToyKeeper1-8/+12
2020-02-05first pass at a smaller simpler thermal regulation algorithm...Selene ToyKeeper1-75/+52
2020-02-05replaced Anduril's gradual adjustment speed code with a smaller simpler versionSelene ToyKeeper1-43/+17
2020-02-03mention the maximum allowed temperature in the manualSelene ToyKeeper1-1/+1
2020-01-30saving state of ADC / WDT refactoring before doing more changes... what chan...Selene ToyKeeper5-76/+59
2020-01-30switched to a pseudo-rolling-average method to reduce noise, set prescaler ba...Selene ToyKeeper1-8/+13
2020-01-29increased effective ADC resolution by switching from continuous-lowpass to su...Selene ToyKeeper1-64/+43
2020-01-29remove truncation noise by adding 0.5 to each resultSelene ToyKeeper1-24/+22
2020-01-29rewrote ADC code to use a continuous lowpass system on all measurements, to e...Selene ToyKeeper5-130/+194
2019-12-17fixed too-slow thermal response (was introduced in the irq-refactor branch)Selene ToyKeeper1-5/+8
2019-12-11added support for Fireflies ROT66 G2 and PL47 G2Selene ToyKeeper2-0/+109
2019-12-04added a compile-time flag to enable/disable momentary mode (suggested by Agro)Selene ToyKeeper1-1/+18
2019-12-04fixed compile errors to handle a couple USE_ flags better:Selene ToyKeeper1-2/+8
2019-12-03added a FW3A build with the FET turned off completelySelene ToyKeeper1-0/+36
2019-12-03adjusted lantern tint ramping power correction again, based on measurements o...Selene ToyKeeper1-1/+1
2019-11-29adjusted BLF Lantern (Sofirn LT1) tint ramping power correction factor to mat...Selene ToyKeeper2-1/+8
2019-11-28changed voltage colors to better match Noctigon K1Selene ToyKeeper2-5/+5
2019-11-25renamed Emisar D1S V2 -> Noctigon K1Selene ToyKeeper1-3/+4
2019-11-25increased Noctigon K1's default temperature limit to 55 CSelene ToyKeeper1-0/+4
2019-11-25calibrated Noctigon K1, changed voltage divider calibration values to 10-bit ...Selene ToyKeeper1-1/+1
2019-11-24enabled muggle mode again in all build targets, since it fits nowSelene ToyKeeper4-23/+0
2019-11-20made the button LED turn off in momentary mode, instead of staying on foreverSelene ToyKeeper1-2/+7
2019-11-20fixed unintentional wakeup right after going to sleepSelene ToyKeeper1-2/+2
2019-11-19Mateminco MF01S can fit muggle mode again, barelySelene ToyKeeper1-3/+3
2019-11-19reduced build size by a few bytesSelene ToyKeeper2-3/+3
2019-11-19the Q8 can just barely fit muggle mode againSelene ToyKeeper1-3/+3
2019-11-19enabled prevent_reboot_loop() on all builds, to reduce the impact of any pote...Selene ToyKeeper1-5/+7
2019-11-19fixed ADC cycles running 2X as fast as intendedSelene ToyKeeper1-8/+8
2019-11-19cleaned up WDT code a bit, reduced total size,Selene ToyKeeper2-29/+25
2019-11-18fixed issue where button-press-during-sleep could occasionally cause a rebootSelene ToyKeeper1-3/+7
2019-11-18added SOS mode to the BLF LT1 Lantern build, because people wanted itSelene ToyKeeper2-7/+44
2019-11-14turned off muggle mode on Q8 and MF01S, to make builds small enough againSelene ToyKeeper2-0/+11
2019-11-14oops, put voltage lowpass on the wrong D4SSelene ToyKeeper2-3/+4
2019-11-14added a lowpass filter for battery voltage measurementsSelene ToyKeeper3-37/+29
2019-11-14fixed factory reset (wasn't running interrupt logic since it's deferred now)Selene ToyKeeper3-12/+11
2019-11-14fixed ADC code; measures and behaves correctly now, and is easier to read...Selene ToyKeeper3-41/+41
2019-11-14started refactoring ADC code to split voltage and temperature into their own ...Selene ToyKeeper2-212/+226
2019-11-14refactored how interrupts work...Selene ToyKeeper10-38/+108
2019-11-13fixed some compile issues related to delay_4ms()Selene ToyKeeper3-2/+2
2019-10-02made lantern's muggle mode brighter (matches default stepped ramp level 4 of 5)Selene ToyKeeper1-0/+3
2019-10-02added a default version.h for people who don't use the build scriptSelene ToyKeeper1-0/+4
2019-09-28after safety ramp-down, if the button remains stuck, lock the lightSelene ToyKeeper1-1/+9
generated by cgit v1.2.3 (git 2.25.1) at 2026-03-29 21:46:13 +0000