aboutsummaryrefslogtreecommitdiff
path: root/spaghetti-monster (unfollow)
Commit message (Collapse)AuthorFilesLines
2021-08-16made dynamic PWM phase-correct; replaced brute-force phase reset to avoid ↵Selene ToyKeeper1-19/+22
flickering (I didn't see any flickering on my lights, but SammysHP reported it was visible)
2021-08-14set KR4 default floor higher at Hank's request,Selene ToyKeeper2-8/+8
and reduced the jump-start-moon power a bit too (he says both are good now, but I don't have hardware to measure it myself) The higher floor is because, when the driver is really hot from being on turbo, going directly to moon causes the LEDs to turn off for a while until the driver cools. The new floor is the lowest level where post-turbo activation works reliably. However, it should turn on even at the level 1/150 when it's not hot.
2021-08-12calibrated KR4 jump-start-moon, may be too high on some older hardwareSelene ToyKeeper2-2/+2
2021-08-12KR4 thermal regulation no longer needs overrides, because dynamic PWM makes ↵Selene ToyKeeper1-2/+3
the defaults work better (the overrides were mostly needed as a side effect of having 1024 PWM steps instead of 256)
2021-08-12got PFM / dynamic PWM actually working on Noctigon KR4Selene ToyKeeper6-28/+83
(and also added "jump start moon" to it) (and generally finished adding dynamic PWM support to FSM)
2021-08-12added a "jump start moon" option for hold-from-off, for lights with ↵Selene ToyKeeper1-0/+13
slow-activating circuits (briefly pulses the light at a higher level to wake up the circuit faster)
2021-08-12made blink_once() brightness configurable per buildSelene ToyKeeper1-2/+5
2021-08-12document the actual maximum for manual memory timer (~140 minutes, not 255)Selene ToyKeeper2-1/+6
2021-07-25added Nichia 219B build for KR4 and K9.3, adjusted 219C builds, for intl-outdoorSelene ToyKeeper5-5/+38
2021-07-25allow building only some targets, instead of always doing allSelene ToyKeeper1-0/+13
2021-07-22summarize results at end of batch build processSelene ToyKeeper1-1/+30
2021-07-11rewrote hybrid memory (manual memory timer) to eliminate corner casesSelene ToyKeeper1-15/+14
Old method: - at 1-click power-on, choose a brightness based on off-time (manual level or last-ramped level) New method: - when off longer than the timer, set last-ramped level to manual level This fixes a bug: - turn light off - wait for timer - turn light on with a shortcut to moon - turn light off - turn light on - pre-patch, light went to last-ramped level instead of manual level This change also reduces the ROM size slightly.
2021-07-11added Emisar D18 Nichia 219 build target (same as normal but reduced FET power)Selene ToyKeeper2-0/+15
2021-07-09set Emisar/Noctigon "219" builds to 65% FET powerSelene ToyKeeper5-8/+20
(was 75% or 80% before) (change requested by Emisar)
2021-05-23added missing ifdefs for compiling without USE_SIMPLE_UISelene ToyKeeper1-1/+9
(compiles now, but isn't tested on hardware)
2021-05-13oops, somehow I forgot to add this earlier... Hank's UI preferences ↵Selene ToyKeeper1-0/+21
(applies to all Emisar / Noctigon lights)
2021-05-07made manual memory remember tint too, not just brightnessSelene ToyKeeper5-17/+33
2021-04-14aux LED config cleaning...Selene ToyKeeper26-107/+15
- use fancy blinking mode by default (define USE_OLD_BLINKING_INDICATOR if old slow mode is wanted) - remove TICK_DURING_STANDBY from all cfg-*.h files because it's enabled automatically by other features anyway (autolock, memory timer) - remove STANDBY_TICK_SPEED from cfg-*.h because all the values matched the default anyway so it was redundant - set rot66 button LED to high+blinking instead of high+off (it was only "off" because it ran out of space, and that was resolved) - enabled fancier indicator by default on fireflies-ui and rampingiosv3, since its other #define clauses were removed (not sure if those older UIs still compile, but if so, it's worth at least trying not to break it)
2021-04-13config updates for Hank (Emisar / Noctigon):Selene ToyKeeper12-7/+11
- use cycling rainbow mode by default on lights with RGB LEDs (instead of voltage, because it's better for impressing new users) - use 2C turbo instead of 2C ceiling (Anduril 1 style instead of Anduril 2 style) also some other minor housekeeping... - make all K1 models use consistent rainbow cycling speed - enable auto-lock and manual memory timer on Emisar D1v2 - remove redundant RGB config on Lume1 (it had incorrect comments anyway)
2021-04-13fixed missing ifdef for simple UISelene ToyKeeper1-1/+4
2021-04-13fixed wrong word in manual (turbo is in full UI only)Selene ToyKeeper1-1/+1
2021-04-02re-numbered t1616 builds to reflect manufacturer betterSelene ToyKeeper5-8/+8
(all the Sofirn ones are pre-production builds intended to go on new Sofirn-produced hardware)
2021-04-02fixed blinking aux LED on gchart-fet1-t1616 (was fast and bright, now uses ↵Selene ToyKeeper1-0/+5
2-level heartbeat pattern)
2021-04-01reverted version.h back to generic originalSelene ToyKeeper1-1/+4
2021-04-01Renamed gchart-fet1-t16 to t1616, to make it consistent with other t1616 models.Selene ToyKeeper2-2/+2
2021-04-01slightly reorganized declaration of PCINT to make it easier to readSelene ToyKeeper1-16/+10
2021-04-01touched up a bit of formatting and a note for later optimizationSelene ToyKeeper1-4/+7
2021-02-01Add RGB Aux functionality for 1-SeriesGabriel Hart2-22/+43
2021-02-01Updated the Sofirn SP10S Anduril boardGabriel Hart2-3/+1
2021-01-25updated MODELS file with missing K9.3-nofet build targetSelene ToyKeeper1-0/+1
2021-01-25removed redundant function call, added missing commentSelene ToyKeeper2-4/+1
2021-01-25bug pseudo-fix: K9.3 lockout mode failed in blinking single-color modeSelene ToyKeeper2-0/+12
because of what appears to be compiler jank or a race condition or some other highly unusual issue (fixed by eating up extra clock cycles in the affected code path)
2021-01-12Clean up a couple unnecessary #defines in gchart fet1 config fileGabriel Hart1-8/+0
2021-01-12Add the override of ATTINY setting to 1616 for the new T1616 config filesGabriel Hart3-0/+3
2021-01-12Add hwdef for BLF Q8 with t1616 and cfg files for the Q8, Lantern, and SP36Gabriel Hart4-0/+166
2021-01-12Rename SP10Ss hwdef file to align with othersGabriel Hart1-1/+1
2021-01-12Add Sofirn SP10S (adapter) and dual-voltage logicGabriel Hart4-1/+36
2020-12-20Fix 1-Series standby tick speed, use 2C TurboGabriel Hart3-3/+6
2020-12-18Add AVR 1-Series and t1616 board and scriptsGabriel Hart9-6/+185
2020-12-13noctigon k9.3: default to aux RGB rainbow mode, and automatic memorySelene ToyKeeper1-2/+3
2020-10-22enabled memory timer and resetting tint after timeout on K9.3Selene ToyKeeper3-2/+15
(unsure if I'll keep it this way though, or if the old way was better)
2020-10-18added model number to Lume1 FW3X build targetSelene ToyKeeper2-0/+5
2020-10-18minor update to anduril-ui.png (added clarification of what "3H" means)Selene ToyKeeper2-27/+5
2020-10-16added K9.3-noFET build target (for models with E21A as main LEDs)Selene ToyKeeper2-1/+55
2020-10-16start tint at 0 instead of 128 on lights with toggle instead of rampSelene ToyKeeper1-0/+4
2020-10-16added ramp 3H -> momentary turboSelene ToyKeeper2-0/+16
2020-10-15made gradual_tick() work on K9.3 (via override), fixed strobe config,Selene ToyKeeper4-9/+87
made blink_once() more configurable (and more reliable on K9.3)
2020-10-14got K9.3 2nd LEDs working (and modified FSM to allow this sort of thing)Selene ToyKeeper5-1/+85
added a way to include per-model code overrides added an override mechanism for logic inside set_level() wrote K9.3's set_level() function added TINT_RAMP_TOGGLE_ONLY mode for tint ramping
2020-10-14configured K9.3 cfg (mostly), assigned a model number, fixed typo in hwdefSelene ToyKeeper2-16/+18
(main LEDs work now; 2nd LEDs not yet) (aux and button LEDs work too, plus switch)
2020-10-14copied KR4 cfg to K9.3 cfgSelene ToyKeeper1-0/+65
generated by cgit v1.2.3 (git 2.25.1) at 2026-03-29 17:07:30 +0000