aboutsummaryrefslogtreecommitdiff
path: root/spaghetti-monster (unfollow)
Commit message (Expand)AuthorFilesLines
2020-03-26Noctigon KR4 needed tighter/faster thermal response, and Hank wants RGB rainb...Selene ToyKeeper1-1/+3
2020-03-26made thermal regulation use a smaller target window, and prioritize cooling moreSelene ToyKeeper1-3/+3
2020-03-21added dynamic underclocking to KR4 to increase moon runtime, fixed ramp miles...Selene ToyKeeper2-15/+11
2020-03-21fixed potential eeprom corruption after turning boost/opamp chip on/offSelene ToyKeeper1-0/+16
2020-03-20enabled soft factory reset on KR4, raised default floor to the lowest reliabl...Selene ToyKeeper2-2/+4
2020-03-20added reboot() support for tiny1634Selene ToyKeeper1-8/+10
2020-03-16removed old thermal junk and voltage_lowpass junk from cfg filesSelene ToyKeeper3-29/+0
2020-03-16fixed calc_voltage_divider() (use 10-bit calibration values, not 8-bit)Selene ToyKeeper1-1/+1
2020-03-16fixed a few things in ramping-ui, rampingiosv3, and werner's UISelene ToyKeeper3-14/+13
2020-03-16merged some misc fixes from pakutrai, cleaned up comments, removed unused sym...Selene ToyKeeper15-87/+18
2020-03-16increased blink speed slightly, and added a library function to blink out 16-...Selene ToyKeeper1-3/+25
2020-03-16added FETless KR4 build target, calibrated other KR4 therm faster level betterSelene ToyKeeper2-2/+47
2020-03-16deleted commented-out WDT code from previous revisionSelene ToyKeeper1-7/+0
2020-03-16cleaned up WDT ADC timer code slightly, and removed a bit of redundant codeSelene ToyKeeper1-6/+8
2020-03-16reduced regulation jitter by biasing errors toward zero by a constant amount,Selene ToyKeeper1-1/+14
2020-03-15the ADC sample count doesn't need to be 16-bit any more, and isn't really a c...Selene ToyKeeper2-3/+4
2020-03-15removed dead comments and dead codeSelene ToyKeeper1-28/+2
2020-03-15replaced temperature_timer (which wasn't even being used) with a variable del...Selene ToyKeeper1-27/+43
2020-03-13tried to make thermal code a bit less twitchy...Selene ToyKeeper3-13/+19
2020-03-06FET ramp was too steep; slowed it down by 50% (20 steps -> 30 steps)Selene ToyKeeper1-11/+10
2020-03-06KR4: added FET channel, measured output, calibrated rampSelene ToyKeeper1-2/+10
2020-03-05initial support for Noctigon KR4Selene ToyKeeper3-0/+76
2020-02-28went back to continuous lowpass because it had the best noise reductionSelene ToyKeeper2-52/+74
2020-02-05brute force method for reducing ADC noise -- average a ridiculous number of s...Selene ToyKeeper2-20/+14
2020-02-05still doesn't work, but at least it's a bit less broken than before...Selene ToyKeeper1-8/+12
2020-02-05first pass at a smaller simpler thermal regulation algorithm...Selene ToyKeeper1-75/+52
2020-02-05replaced Anduril's gradual adjustment speed code with a smaller simpler versionSelene ToyKeeper1-43/+17
2020-02-03mention the maximum allowed temperature in the manualSelene ToyKeeper1-1/+1
2020-01-30saving state of ADC / WDT refactoring before doing more changes... what chan...Selene ToyKeeper5-76/+59
2020-01-30switched to a pseudo-rolling-average method to reduce noise, set prescaler ba...Selene ToyKeeper1-8/+13
2020-01-29increased effective ADC resolution by switching from continuous-lowpass to su...Selene ToyKeeper1-64/+43
2020-01-29remove truncation noise by adding 0.5 to each resultSelene ToyKeeper1-24/+22
2020-01-29rewrote ADC code to use a continuous lowpass system on all measurements, to e...Selene ToyKeeper5-130/+194
2019-12-17fixed too-slow thermal response (was introduced in the irq-refactor branch)Selene ToyKeeper1-5/+8
2019-12-11added support for Fireflies ROT66 G2 and PL47 G2Selene ToyKeeper2-0/+109
2019-12-04added a compile-time flag to enable/disable momentary mode (suggested by Agro)Selene ToyKeeper1-1/+18
2019-12-04fixed compile errors to handle a couple USE_ flags better:Selene ToyKeeper1-2/+8
2019-12-03added a FW3A build with the FET turned off completelySelene ToyKeeper1-0/+36
2019-12-03adjusted lantern tint ramping power correction again, based on measurements o...Selene ToyKeeper1-1/+1
2019-11-29adjusted BLF Lantern (Sofirn LT1) tint ramping power correction factor to mat...Selene ToyKeeper2-1/+8
2019-11-28changed voltage colors to better match Noctigon K1Selene ToyKeeper2-5/+5
2019-11-25renamed Emisar D1S V2 -> Noctigon K1Selene ToyKeeper1-3/+4
2019-11-25increased Noctigon K1's default temperature limit to 55 CSelene ToyKeeper1-0/+4
2019-11-25calibrated Noctigon K1, changed voltage divider calibration values to 10-bit ...Selene ToyKeeper1-1/+1
2019-11-24enabled muggle mode again in all build targets, since it fits nowSelene ToyKeeper4-23/+0
2019-11-20made the button LED turn off in momentary mode, instead of staying on foreverSelene ToyKeeper1-2/+7
2019-11-20fixed unintentional wakeup right after going to sleepSelene ToyKeeper1-2/+2
2019-11-19Mateminco MF01S can fit muggle mode again, barelySelene ToyKeeper1-3/+3
2019-11-19reduced build size by a few bytesSelene ToyKeeper2-3/+3
2019-11-19the Q8 can just barely fit muggle mode againSelene ToyKeeper1-3/+3
generated by cgit v1.2.3 (git 2.25.1) at 2026-03-29 13:10:37 +0000