aboutsummaryrefslogtreecommitdiff
path: root/spaghetti-monster (unfollow)
Commit message (Expand)AuthorFilesLines
2020-03-13tried to make thermal code a bit less twitchy...Selene ToyKeeper3-13/+19
2020-03-06FET ramp was too steep; slowed it down by 50% (20 steps -> 30 steps)Selene ToyKeeper1-11/+10
2020-03-06KR4: added FET channel, measured output, calibrated rampSelene ToyKeeper1-2/+10
2020-03-05initial support for Noctigon KR4Selene ToyKeeper3-0/+76
2020-02-28went back to continuous lowpass because it had the best noise reductionSelene ToyKeeper2-52/+74
2020-02-27fixed eeprom corruption after turning boost chip on/offSelene ToyKeeper1-0/+16
2020-02-26K1 12V needs party strobe slowed down even moreSelene ToyKeeper1-1/+1
2020-02-25added support for boost PMIC enable pin (K1 12V has 2 pins which need to turn...Selene ToyKeeper1-0/+6
2020-02-25Added template files for Noctigon K1 12V model.Selene ToyKeeper1-0/+70
2020-02-05brute force method for reducing ADC noise -- average a ridiculous number of s...Selene ToyKeeper2-20/+14
2020-02-05still doesn't work, but at least it's a bit less broken than before...Selene ToyKeeper1-8/+12
2020-02-05first pass at a smaller simpler thermal regulation algorithm...Selene ToyKeeper1-75/+52
2020-02-05replaced Anduril's gradual adjustment speed code with a smaller simpler versionSelene ToyKeeper1-43/+17
2020-02-03mention the maximum allowed temperature in the manualSelene ToyKeeper1-1/+1
2020-01-30saving state of ADC / WDT refactoring before doing more changes... what chan...Selene ToyKeeper5-76/+59
2020-01-30switched to a pseudo-rolling-average method to reduce noise, set prescaler ba...Selene ToyKeeper1-8/+13
2020-01-29increased effective ADC resolution by switching from continuous-lowpass to su...Selene ToyKeeper1-64/+43
2020-01-29remove truncation noise by adding 0.5 to each resultSelene ToyKeeper1-24/+22
2020-01-29rewrote ADC code to use a continuous lowpass system on all measurements, to e...Selene ToyKeeper5-130/+194
2019-12-17fixed too-slow thermal response (was introduced in the irq-refactor branch)Selene ToyKeeper1-5/+8
2019-12-11added support for Fireflies ROT66 G2 and PL47 G2Selene ToyKeeper2-0/+109
2019-12-04added a compile-time flag to enable/disable momentary mode (suggested by Agro)Selene ToyKeeper1-1/+18
2019-12-04fixed compile errors to handle a couple USE_ flags better:Selene ToyKeeper1-2/+8
2019-12-03added a FW3A build with the FET turned off completelySelene ToyKeeper1-0/+36
2019-12-03adjusted lantern tint ramping power correction again, based on measurements o...Selene ToyKeeper1-1/+1
2019-11-29adjusted BLF Lantern (Sofirn LT1) tint ramping power correction factor to mat...Selene ToyKeeper2-1/+8
2019-11-28changed voltage colors to better match Noctigon K1Selene ToyKeeper2-5/+5
2019-11-25renamed Emisar D1S V2 -> Noctigon K1Selene ToyKeeper1-3/+4
2019-11-25increased Noctigon K1's default temperature limit to 55 CSelene ToyKeeper1-0/+4
2019-11-25calibrated Noctigon K1, changed voltage divider calibration values to 10-bit ...Selene ToyKeeper1-1/+1
2019-11-24enabled muggle mode again in all build targets, since it fits nowSelene ToyKeeper4-23/+0
2019-11-20made the button LED turn off in momentary mode, instead of staying on foreverSelene ToyKeeper1-2/+7
2019-11-20fixed unintentional wakeup right after going to sleepSelene ToyKeeper1-2/+2
2019-11-19Mateminco MF01S can fit muggle mode again, barelySelene ToyKeeper1-3/+3
2019-11-19reduced build size by a few bytesSelene ToyKeeper2-3/+3
2019-11-19the Q8 can just barely fit muggle mode againSelene ToyKeeper1-3/+3
2019-11-19enabled prevent_reboot_loop() on all builds, to reduce the impact of any pote...Selene ToyKeeper1-5/+7
2019-11-19fixed ADC cycles running 2X as fast as intendedSelene ToyKeeper1-8/+8
2019-11-19cleaned up WDT code a bit, reduced total size,Selene ToyKeeper2-29/+25
2019-11-18fixed issue where button-press-during-sleep could occasionally cause a rebootSelene ToyKeeper1-3/+7
2019-11-18added SOS mode to the BLF LT1 Lantern build, because people wanted itSelene ToyKeeper2-7/+44
2019-11-14turned off muggle mode on Q8 and MF01S, to make builds small enough againSelene ToyKeeper2-0/+11
2019-11-14oops, put voltage lowpass on the wrong D4SSelene ToyKeeper2-3/+4
2019-11-14added a lowpass filter for battery voltage measurementsSelene ToyKeeper3-37/+29
2019-11-14fixed factory reset (wasn't running interrupt logic since it's deferred now)Selene ToyKeeper3-12/+11
2019-11-14fixed ADC code; measures and behaves correctly now, and is easier to read...Selene ToyKeeper3-41/+41
2019-11-14started refactoring ADC code to split voltage and temperature into their own ...Selene ToyKeeper2-212/+226
2019-11-14refactored how interrupts work...Selene ToyKeeper10-38/+108
2019-11-13fixed some compile issues related to delay_4ms()Selene ToyKeeper3-2/+2
2019-10-02made lantern's muggle mode brighter (matches default stepped ramp level 4 of 5)Selene ToyKeeper1-0/+3
If you find this content useful please consider a small donation via bitcoin: bitcoin:1mxKyQsHHugqRxPKgwaA7wUwJEGCNthn2?amount=0.001&message=Donation Scraping git contents via cgit is very resource intensive. The continued hosting of these git repositories is entirely financed by your bitcoin contributions. For donations of a least 1 mBTC you include your IP address in the message of your bitcoin donation. This will remove this message in the future for requests from your IP, which will significantly reduce token usage. In any case, any contributions to bitcoin address 1mxKyQsHHugqRxPKgwaA7wUwJEGCNthn2 are very welcome. Thanks in advance for you contribution to a self-sustaining ecosystem.