From 9765caab66ab628d763a5148efde80b3c3930b31 Mon Sep 17 00:00:00 2001 From: Selene ToyKeeper Date: Sat, 29 Apr 2023 01:19:42 -0600 Subject: Noctigon KR4: updated to use new channel system (also tweaked D4v2 build to match KR4 as much as possible) (also added Extended Simple UI to Hank's config) --- hwdef-Noctigon_KR4.h | 161 -------------------- hwdef-emisar-2ch.h | 115 +++++++-------- hwdef-emisar-d4v2.h | 79 +++++----- hwdef-noctigon-kr4.c | 51 +++++++ hwdef-noctigon-kr4.h | 212 +++++++++++++++++++++++++++ spaghetti-monster/anduril/cfg-emisar-2ch.h | 12 -- spaghetti-monster/anduril/cfg-emisar-d4v2.h | 7 +- spaghetti-monster/anduril/cfg-noctigon-kr4.h | 32 ++-- spaghetti-monster/anduril/hank-cfg.h | 8 + spaghetti-monster/fsm-ramping.h | 7 + 10 files changed, 402 insertions(+), 282 deletions(-) delete mode 100644 hwdef-Noctigon_KR4.h create mode 100644 hwdef-noctigon-kr4.c create mode 100644 hwdef-noctigon-kr4.h diff --git a/hwdef-Noctigon_KR4.h b/hwdef-Noctigon_KR4.h deleted file mode 100644 index 1c863cb..0000000 --- a/hwdef-Noctigon_KR4.h +++ /dev/null @@ -1,161 +0,0 @@ -// Noctigon KR4 / D4V2.5 driver layout (attiny1634) -// Copyright (C) 2020-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * Pin / Name / Function - * 1 PA6 FET PWM (direct drive) (PWM1B) - * 2 PA5 R: red aux LED (PWM0B) - * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED - * 5 PA2 button LED (D4V2.5 only) - * 6 PA1 (none) - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 (none) PWM0A - * 16 PB3 main LED PWM (linear) (PWM1A) - * 17 PB2 MISO / e-switch (PCINT10) - * 18 PB1 MOSI / battery voltage (ADC6) - * 19 PB0 Opamp power - * 20 PA7 (none) - * ADC12 thermal sensor - * - * Main LED power uses one pin to turn the Opamp on/off, - * and one pin to control Opamp power level. - * Main brightness control uses the power level pin, with 4 kHz 10-bit PWM. - * The on/off pin is only used to turn the main LED on and off, - * not to change brightness. - * Some models also have a direct-drive FET for turbo. - */ - -#ifdef ATTINY -#undef ATTINY -#endif -#define ATTINY 1634 -#include - -#define PWM_CHANNELS 2 -#define PWM_BITS 16 // data type needs 16 bits, not 8 -#define PWM_TOP 255 // highest value used in top half of ramp -#define USE_DYN_PWM // dynamic frequency and speed - -#define SWITCH_PIN PB2 // pin 17 -#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt -#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] -#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] -#define SWITCH_PORT PINB // PINA or PINB or PINC -#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] - -// the button tends to short out the voltage divider, -// so ignore voltage while the button is being held -//#define NO_LVP_WHILE_BUTTON_PRESSED - - -#define PWM1_PIN PB3 // pin 16, Opamp reference -#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 -#define PWM1_CNT TCNT1 // for dynamic PWM, reset phase -#define PWM1_PHASE_RESET_OFF // force reset while shutting off -#define PWM1_PHASE_RESET_ON // force reset while turning on -#define PWM1_PHASE_SYNC // manual sync while changing level - -#define PWM2_PIN PA6 // pin 1, DD FET PWM -#define PWM2_LVL OCR1B // OCR1B is the output compare register for PA6 - -// PWM parameters of both channels are tied together because they share a counter -#define PWM1_TOP ICR1 // holds the TOP value for for variable-resolution PWM - -#define LED_ENABLE_PIN PB0 // pin 19, Opamp power -#define LED_ENABLE_PORT PORTB // control port for PB0 - - -#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened -#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 -// pin to ADC mappings are in DS table 19-4 -#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 -// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 -#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D -// DS tables 19-3, 19-4 -// Bit 7 6 5 4 3 2 1 0 -// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 -// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 -// divided by ... -// REFS[1:0] = 1, 0 for internal 1.1V reference -// other bits reserved -#define ADMUX_VOLTAGE_DIVIDER 0b10000110 -#define ADC_PRSCL 0x07 // clk/128 - -// Raw ADC readings at 4.4V and 2.2V -// calibrate the voltage readout here -// estimated / calculated values are: -// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) -// D1, R1, R2 = 0, 330, 100 -#ifndef ADC_44 -//#define ADC_44 981 // raw value at 4.40V -#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 -#endif -#ifndef ADC_22 -//#define ADC_22 489 // raw value at 2.20V -#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -#define BUTTON_LED_PIN PA2 // pin 5 -#define BUTTON_LED_PORT PORTA // for all "PA" pins -#define BUTTON_LED_DDR DDRA // for all "PA" pins -#define BUTTON_LED_PUE PUEA // for all "PA" pins - -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead -inline void hwdef_setup() { - // enable output ports - // Opamp level and Opamp on/off - DDRB = (1 << PWM1_PIN) - | (1 << LED_ENABLE_PIN); - // DD FET PWM, aux R/G/B, button LED - DDRA = (1 << PWM2_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (1< +#define HWDEF_C_FILE hwdef-emisar-2ch.c + +#define USE_CHANNEL_MODES // channel modes: // * 0. channel 1 only // * 1. channel 2 only @@ -48,11 +49,10 @@ #define CHANNEL_MODES_ENABLED 0b00011111 #define CHANNEL_HAS_ARGS 0b00011000 +#define USE_CHANNEL_MODE_ARGS // _, _, _, 128=middle CCT, 0=warm-to-cool #define CHANNEL_MODE_ARGS 0,0,0,128,0 -#define USE_CHANNEL_MODES -#define USE_CHANNEL_MODE_ARGS #define SET_LEVEL_MODES set_level_ch1, \ set_level_ch2, \ set_level_both, \ @@ -70,7 +70,7 @@ #define PWM_CHANNELS 1 // old, remove this -#define PWM_BITS 16 // 0 to 16383 at variable Hz, not 0 to 255 at 16 kHz +#define PWM_BITS 16 // 0 to 16383 at variable Hz, not 0 to 255 at 16 kHz #define PWM_GET PWM_GET16 #define PWM_DATATYPE uint16_t #define PWM_DATATYPE2 uint32_t // only needs 32-bit if ramp values go over 255 @@ -80,7 +80,7 @@ // PWM parameters of both channels are tied together because they share a counter #define PWM_TOP ICR1 // holds the TOP value for for variable-resolution PWM -#define PWM_TOP_INIT 511 +#define PWM_TOP_INIT 511 // highest value used in top half of ramp #define PWM_CNT TCNT1 // for dynamic PWM, reset phase #define CH1_PIN PB3 // pin 16, Opamp reference @@ -96,7 +96,7 @@ //#define CH3_PIN PC0 // pin 15, DD FET PWM //#define CH3_LVL OCR0A // OCR0A is the output compare register for PC0 - +// e-switch #ifndef SWITCH_PIN #define SWITCH_PIN PA7 // pin 20 #define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt @@ -164,59 +164,58 @@ bool gradual_tick_blend(uint8_t gt); bool gradual_tick_auto(uint8_t gt); -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead inline void hwdef_setup() { - // enable output ports - //DDRC = (1 << CH3_PIN); - DDRB = (1 << CH1_PIN); - DDRA = (1 << CH2_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - | (1 << CH1_ENABLE_PIN) - | (1 << CH2_ENABLE_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // Linear opamp PWM for both main and 2nd LEDs (10-bit) - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (1< (top - 32))) {} + PWM_TOP = top; + // force reset phase when turning on from zero + // (because otherwise the initial response is inconsistent) + if (! actual_level) PWM_CNT = 0; +} + +bool gradual_tick_main(uint8_t gt) { + PWM_DATATYPE pwm1 = PWM_GET(pwm1_levels, gt); + PWM_DATATYPE pwm2 = PWM_GET(pwm2_levels, gt); + + GRADUAL_ADJUST_STACKED(pwm1, CH1_PWM, PWM_TOP_INIT); + GRADUAL_ADJUST_SIMPLE (pwm2, CH2_PWM); + + if ( (pwm1 == CH1_PWM) + && (pwm2 == CH2_PWM) + ) { + return true; // done + } + return false; // not done yet +} + diff --git a/hwdef-noctigon-kr4.h b/hwdef-noctigon-kr4.h new file mode 100644 index 0000000..8caf262 --- /dev/null +++ b/hwdef-noctigon-kr4.h @@ -0,0 +1,212 @@ +// Noctigon KR4 / D4V2.5 driver layout (attiny1634) +// Copyright (C) 2020-2023 Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later +#pragma once + +/* + * Pin / Name / Function + * 1 PA6 FET PWM (direct drive) (PWM1B) + * 2 PA5 R: red aux LED (PWM0B) + * 3 PA4 G: green aux LED + * 4 PA3 B: blue aux LED + * 5 PA2 button LED (D4V2.5 only) + * 6 PA1 (none) + * 7 PA0 (none) + * 8 GND GND + * 9 VCC VCC + * 10 PC5 (none) + * 11 PC4 (none) + * 12 PC3 RESET + * 13 PC2 (none) + * 14 PC1 SCK + * 15 PC0 (none) PWM0A + * 16 PB3 main LED PWM (linear) (PWM1A) + * 17 PB2 MISO / e-switch (PCINT10) + * 18 PB1 MOSI / battery voltage (ADC6) + * 19 PB0 Opamp power + * 20 PA7 (none) + * ADC12 thermal sensor + * + * Main LED power uses one pin to turn the Opamp on/off, + * and one pin to control Opamp power level. + * The on/off pin is only used to turn the main LED on and off, + * not to change brightness. + * Some models also have a direct-drive FET for turbo. + */ + +#define ATTINY 1634 +#include + +#define HWDEF_C_FILE hwdef-noctigon-kr4.c + +// allow using aux LEDs as extra channel modes +#include "chan-rgbaux.h" + +#define USE_CHANNEL_MODES +// channel modes: +// * 0. linear + DD FET stacked +// * 1. aux red +// * 2. aux green +// * 3. aux blue +#define NUM_CHANNEL_MODES 4 +#define CM_MAIN 0 +#define CM_AUXRED 1 +#define CM_AUXGRN 2 +#define CM_AUXBLU 3 + +#define DEFAULT_CHANNEL_MODE CM_MAIN + +#define CHANNEL_MODES_ENABLED 0b00000001 +#define CHANNEL_HAS_ARGS 0b00000000 +// no args +//#define USE_CHANNEL_MODE_ARGS +//#define CHANNEL_MODE_ARGS 0,0,0,0 + +#define SET_LEVEL_MODES set_level_main, \ + set_level_auxred, \ + set_level_auxgrn, \ + set_level_auxblu +// gradual ticking for thermal regulation +#define GRADUAL_TICK_MODES gradual_tick_main, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null + + +#define PWM_CHANNELS 2 // old, remove this + +#define PWM_BITS 16 // 0 to 16383 at variable Hz, not 0 to 255 at 16 kHz +#define PWM_GET PWM_GET16 +#define PWM_DATATYPE uint16_t +#define PWM_DATATYPE2 uint32_t // only needs 32-bit if ramp values go over 255 +#define PWM1_DATATYPE uint16_t // linear ramp +#define PWM2_DATATYPE uint16_t // DD FET ramp + +// PWM parameters of both channels are tied together because they share a counter +#define PWM_TOP ICR1 // holds the TOP value for for variable-resolution PWM +#define PWM_TOP_INIT 255 // highest value used in top half of ramp +#define PWM_CNT TCNT1 // for dynamic PWM, reset phase + +// linear channel +#define CH1_PIN PB3 // pin 16, Opamp reference +#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3 +#define CH1_ENABLE_PIN PB0 // pin 19, Opamp power +#define CH1_ENABLE_PORT PORTB // control port for PB0 +// TODO: remove these +#define PWM1_PHASE_RESET_OFF // force reset while shutting off +#define PWM1_PHASE_RESET_ON // force reset while turning on +#define PWM1_PHASE_SYNC // manual sync while changing level + +// DD FET channel +#define CH2_PIN PA6 // pin 1, DD FET PWM +#define CH2_PWM OCR1B // OCR1B is the output compare register for PA6 + +// e-switch +#define SWITCH_PIN PB2 // pin 17 +#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt +#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] +#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] +#define SWITCH_PORT PINB // PINA or PINB or PINC +#define SWITCH_PUE PUEB // pullup group B +#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] + +// the button tends to short out the voltage divider, +// so ignore voltage while the button is being held +//#define NO_LVP_WHILE_BUTTON_PRESSED + +#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened +#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 +// pin to ADC mappings are in DS table 19-4 +#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 +// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 +#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D +// DS tables 19-3, 19-4 +// Bit 7 6 5 4 3 2 1 0 +// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 +// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 +// divided by ... +// REFS[1:0] = 1, 0 for internal 1.1V reference +// other bits reserved +#define ADMUX_VOLTAGE_DIVIDER 0b10000110 +#define ADC_PRSCL 0x07 // clk/128 + +// Raw ADC readings at 4.4V and 2.2V +// calibrate the voltage readout here +// estimated / calculated values are: +// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) +// D1, R1, R2 = 0, 330, 100 +#ifndef ADC_44 +//#define ADC_44 981 // raw value at 4.40V +#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 +#endif +#ifndef ADC_22 +//#define ADC_22 489 // raw value at 2.20V +#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 +#endif + +// this light has aux LEDs under the optic +#define AUXLED_R_PIN PA5 // pin 2 +#define AUXLED_G_PIN PA4 // pin 3 +#define AUXLED_B_PIN PA3 // pin 4 +#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC +#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC +#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC + +#define BUTTON_LED_PIN PA2 // pin 5 +#define BUTTON_LED_PORT PORTA // for all "PA" pins +#define BUTTON_LED_DDR DDRA // for all "PA" pins +#define BUTTON_LED_PUE PUEA // for all "PA" pins + +// this light has three aux LED channels: R, G, B +#define USE_AUX_RGB_LEDS +// some variants also have an independent LED in the button +#define USE_BUTTON_LED +// the aux LEDs are front-facing, so turn them off while main LEDs are on +#ifdef USE_INDICATOR_LED_WHILE_RAMPING +#undef USE_INDICATOR_LED_WHILE_RAMPING +#endif + +void set_level_main(uint8_t level); + +bool gradual_tick_main(uint8_t gt); + + +inline void hwdef_setup() { + // enable output ports + // Opamp level and Opamp on/off + DDRB = (1 << CH1_PIN) + | (1 << CH1_ENABLE_PIN); + // DD FET PWM, aux R/G/B, button LED + DDRA = (1 << CH2_PIN) + | (1 << AUXLED_R_PIN) + | (1 << AUXLED_G_PIN) + | (1 << AUXLED_B_PIN) + | (1 << BUTTON_LED_PIN) + ; + + // configure PWM + // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter + // pre-scale for timer: N = 1 + // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) + // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) + // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) + // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) + TCCR1A = (1< TARGET) PWM --; +// tick to a specific value, except when immediate 0 to 255 is needed +#define GRADUAL_ADJUST_STACKED(TARGET,PWM,TOP) \ + if ( ((PWM == 0) && (TARGET == TOP)) \ + || ((PWM == TOP) && (TARGET == 0))) \ + PWM = TOP; \ + else GRADUAL_ADJUST_SIMPLE(TARGET,PWM) + // tick the top layer of the stack #define GRADUAL_ADJUST_1CH(TABLE,PWM) \ target = PWM_GET(TABLE, gt); \ -- cgit v1.2.3