From cf0ed5c4bd07e191088977722010e9eec94a7c05 Mon Sep 17 00:00:00 2001
From: Selene ToyKeeper
Date: Fri, 3 Nov 2023 09:07:37 -0600
Subject: moved variant builds under their parent, like "d4-219" -> "d4/219"

---
 hw/hank/noctigon-dm11-boost/hwdef.h | 206 ------------------------------------
 1 file changed, 206 deletions(-)
 delete mode 100644 hw/hank/noctigon-dm11-boost/hwdef.h

(limited to 'hw/hank/noctigon-dm11-boost/hwdef.h')

diff --git a/hw/hank/noctigon-dm11-boost/hwdef.h b/hw/hank/noctigon-dm11-boost/hwdef.h
deleted file mode 100644
index dffd462..0000000
--- a/hw/hank/noctigon-dm11-boost/hwdef.h
+++ /dev/null
@@ -1,206 +0,0 @@
-// Noctigon DM11 boost driver layout (attiny1634)
-// Copyright (C) 2021-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * (based on Noctigon K1)
- *
- * Pin / Name / Function
- *   1    PA6   (none) (PWM1B) (reserved for DD drivers)
- *   2    PA5   R: red aux LED (PWM0B)
- *   3    PA4   G: green aux LED
- *   4    PA3   B: blue aux LED
- *   5    PA2   L: button LED
- *   6    PA1   (none)
- *   7    PA0   (none)
- *   8    GND   GND
- *   9    VCC   VCC
- *  10    PC5   (none)
- *  11    PC4   (none)
- *  12    PC3   RESET
- *  13    PC2   (none)
- *  14    PC1   SCK
- *  15    PC0   boost PMIC enable (PWM0A not used)
- *  16    PB3   main LED PWM (PWM1A)
- *  17    PB2   MISO (PCINT10)
- *  18    PB1   MOSI / battery voltage (ADC6)
- *  19    PB0   Opamp power
- *  20    PA7   e-switch  (PCINT7)
- *      ADC12   thermal sensor
- *
- * Main LED power uses one pin to turn the Opamp on/off,
- * and one pin to control Opamp power level.
- * Regulated brightness control uses the power level pin, with PWM+DSM.
- * The on/off pin is only used to turn the main LED on and off,
- * not to change brightness.
- */
-
-#define ATTINY 1634
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hank/noctigon-dm11-boost/hwdef.c
-
-// allow using aux LEDs as extra channel modes
-#include "fsm/chan-rgbaux.h"
-
-// channel modes:
-// * 0. main LEDs
-// * 1+. aux RGB
-#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
-enum CHANNEL_MODES {
-    CM_MAIN = 0,
-    RGB_AUX_ENUMS
-};
-
-#define DEFAULT_CHANNEL_MODE  CM_MAIN
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b0000000000000001
-// no args
-//#define USE_CHANNEL_MODE_ARGS
-//#define CHANNEL_MODE_ARGS     0,0,0,0,0,0,0,0
-
-
-#define PWM_CHANNELS  1  // old, remove this
-
-#define PWM_BITS      16        // 0 to 32640 (0 to 255 PWM + 0 to 127 DSM) at constant kHz
-#define PWM_GET       PWM_GET16
-#define PWM_DATATYPE  uint16_t
-#define PWM_DATATYPE2 uint32_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint16_t  // 15-bit PWM+DSM ramp
-
-#define PWM_TOP       ICR1   // holds the TOP value for variable-resolution PWM
-#define PWM_TOP_INIT  255
-#define PWM_CNT       TCNT1  // for checking / resetting phase
-// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM)
-#define DSM_TOP       (255<<7) // 15-bit resolution leaves 1 bit for carry
-
-// timer interrupt for DSM
-#define DSM_vect     TIMER1_OVF_vect
-#define DSM_INTCTRL  TIMSK
-#define DSM_OVF_bm   (1<<TOIE1)
-
-#define DELAY_FACTOR 90  // less time in delay() because more time spent in interrupts
-
-// regulated channel
-uint16_t ch1_dsm_lvl;
-uint8_t ch1_pwm, ch1_dsm;
-#define CH1_PIN          PB3    // pin 16, Opamp reference
-#define CH1_PWM          OCR1A  // OCR1A is the output compare register for PB3
-
-#define CH1_ENABLE_PIN   PB0    // pin 19, Opamp power
-#define CH1_ENABLE_PORT  PORTB  // control port for PB0
-
-#define CH1_ENABLE_PIN2  PC0   // pin 15, boost PMIC enable
-#define CH1_ENABLE_PORT2 PORTC // control port for PC0
-
-// e-switch
-#define SWITCH_PIN   PA7     // pin 20
-#define SWITCH_PCINT PCINT7  // pin 20 pin change interrupt
-#define SWITCH_PCIE  PCIE0   // PCIE0 is for PCINT[7:0]
-#define SWITCH_PCMSK PCMSK0  // PCMSK0 is for PCINT[7:0]
-#define SWITCH_PORT  PINA    // PINA or PINB or PINC
-#define SWITCH_PUE   PUEA    // pullup group A
-#define PCINT_vect   PCINT0_vect  // ISR for PCINT[7:0]
-
-#define USE_VOLTAGE_DIVIDER  // use a dedicated pin, not VCC, because VCC input is flattened
-#define VOLTAGE_PIN PB1      // Pin 18 / PB1 / ADC6
-// pin to ADC mappings are in DS table 19-4
-#define VOLTAGE_ADC      ADC6D  // digital input disable pin for PB1
-// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6
-#define VOLTAGE_ADC_DIDR DIDR1  // DIDR channel for ADC6D
-// DS tables 19-3, 19-4
-// Bit   7     6     5      4     3    2    1    0
-//     REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0
-// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1
-// divided by ...
-// REFS[1:0] = 1, 0 for internal 1.1V reference
-// other bits reserved
-#define ADMUX_VOLTAGE_DIVIDER 0b10000110
-#define ADC_PRSCL   0x07    // clk/128
-
-// Raw ADC readings at 4.4V and 2.2V
-// calibrate the voltage readout here
-// estimated / calculated values are:
-//   (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
-// D1, R1, R2 = 0, 330, 100
-#ifndef ADC_44
-//#define ADC_44 981  // raw value at 4.40V
-#define ADC_44 967  // manually tweaked so 4.16V will blink out 4.2
-#endif
-#ifndef ADC_22
-//#define ADC_22 489  // raw value at 2.20V
-#define ADC_22 482  // manually tweaked so 4.16V will blink out 4.2
-#endif
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN    PA5    // pin 2
-#define AUXLED_G_PIN    PA4    // pin 3
-#define AUXLED_B_PIN    PA3    // pin 4
-#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC
-
-#define BUTTON_LED_PIN  PA2    // pin 5
-#define BUTTON_LED_PORT PORTA  // for all "PA" pins
-#define BUTTON_LED_DDR  DDRA   // for all "PA" pins
-#define BUTTON_LED_PUE  PUEA   // for all "PA" pins
-
-// this light has three aux LED channels: R, G, B
-#define USE_AUX_RGB_LEDS
-// it also has an independent LED in the button
-#define USE_BUTTON_LED
-// the aux LEDs are front-facing, so turn them off while main LEDs are on
-#ifdef USE_INDICATOR_LED_WHILE_RAMPING
-#undef USE_INDICATOR_LED_WHILE_RAMPING
-#endif
-
-
-inline void hwdef_setup() {
-    // enable output ports
-    // boost PMIC on/off
-    DDRC = (1 << CH1_ENABLE_PIN2);
-    // Opamp level and Opamp on/off
-    DDRB = (1 << CH1_PIN)
-         | (1 << CH1_ENABLE_PIN);
-    // aux R/G/B, button LED
-    DDRA = (1 << AUXLED_R_PIN)
-         | (1 << AUXLED_G_PIN)
-         | (1 << AUXLED_B_PIN)
-         | (1 << BUTTON_LED_PIN)
-         ;
-
-    // configure PWM
-    // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-    // pre-scale for timer: N = 1
-    // PWM for both channels
-    // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
-    // WGM1[3:0]: 1,1,1,0: PWM, Fast, adjustable (DS table 12-5)
-    // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
-    // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
-    // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)
-    TCCR1A = (1<<WGM11)  | (0<<WGM10)   // adjustable PWM (TOP=ICR1) (DS table 12-5)
-           | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-           | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
-           ;
-    TCCR1B = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-           //| (1<<WGM13)  | (1<<WGM12)  // fast adjustable PWM (DS table 12-5)
-           | (1<<WGM13)  | (0<<WGM12)  // phase-correct adjustable PWM (DS table 12-5)
-           ;
-
-    // set PWM resolution
-    PWM_TOP = PWM_TOP_INIT;
-
-    // set up interrupt for delta-sigma modulation
-    // (moved to hwdef.c functions so it can be enabled/disabled based on ramp level)
-    //DSM_INTCTRL |= DSM_OVF_bm;  // interrupt once for each timer cycle
-
-    // set up e-switch
-    SWITCH_PUE = (1 << SWITCH_PIN);  // pull-up for e-switch
-    SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
-}
-
-
-#define LAYOUT_DEFINED
-
-- 
cgit v1.2.3