From 583854e37efde7f461e073e735a1736b02d28c70 Mon Sep 17 00:00:00 2001 From: Selene ToyKeeper Date: Mon, 17 Apr 2023 00:08:32 -0600 Subject: switched the rest of FSM + Anduril to use SPDX license headers instead of full GPL headers (or all too often, nothing at all) There are a few "FIXME" entries where I'm not sure about the correct copyright. --- hwdef-Noctigon_K1.h | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'hwdef-Noctigon_K1.h') diff --git a/hwdef-Noctigon_K1.h b/hwdef-Noctigon_K1.h index 4c0ce05..2e44e23 100644 --- a/hwdef-Noctigon_K1.h +++ b/hwdef-Noctigon_K1.h @@ -1,7 +1,9 @@ -#ifndef HWDEF_NOCTIGON_K1_H -#define HWDEF_NOCTIGON_K1_H +// Noctigon K1 driver layout (attiny1634) +// Copyright (C) 2019-2023 Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later +#pragma once -/* Noctigon K1 driver layout (attiny1634) +/* * (originally known as Emisar D1S V2) * * Pin / Name / Function @@ -131,4 +133,3 @@ inline void hwdef_setup() { #define LAYOUT_DEFINED -#endif -- cgit v1.2.3 From d4e948ab54c8f71db2790a964668e1f3b399e7db Mon Sep 17 00:00:00 2001 From: Selene ToyKeeper Date: Fri, 21 Jul 2023 15:47:52 -0600 Subject: converted noctigon-k1 to multi-channel --- hwdef-Noctigon_K1.h | 135 ---------------------------------------------------- 1 file changed, 135 deletions(-) delete mode 100644 hwdef-Noctigon_K1.h (limited to 'hwdef-Noctigon_K1.h') diff --git a/hwdef-Noctigon_K1.h b/hwdef-Noctigon_K1.h deleted file mode 100644 index 2e44e23..0000000 --- a/hwdef-Noctigon_K1.h +++ /dev/null @@ -1,135 +0,0 @@ -// Noctigon K1 driver layout (attiny1634) -// Copyright (C) 2019-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * (originally known as Emisar D1S V2) - * - * Pin / Name / Function - * 1 PA6 (none) (PWM1B) (reserved for DD drivers) - * 2 PA5 R: red aux LED (PWM0B) - * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED - * 5 PA2 (none) (reserved for L: button LED (on some models)) - * 6 PA1 (none) - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 (none) PWM0A - * 16 PB3 main LED PWM (PWM1A) - * 17 PB2 MISO - * 18 PB1 MOSI / battery voltage (ADC6) - * 19 PB0 Opamp power - * 20 PA7 e-switch (PCINT7) - * ADC12 thermal sensor - * - * Main LED power uses one pin to turn the Opamp on/off, - * and one pin to control Opamp power level. - * All brightness control uses the power level pin, with 4 kHz 10-bit PWM. - * The on/off pin is only used to turn the main LED on and off, - * not to change brightness. - */ - -#ifdef ATTINY -#undef ATTINY -#endif -#define ATTINY 1634 -#include - -#define PWM_CHANNELS 1 -#define PWM_BITS 10 // 0 to 1023 at 4 kHz, not 0 to 255 at 16 kHz -#define PWM_TOP 1023 - -#define SWITCH_PIN PA7 // pin 20 -#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC - -#define PWM1_PIN PB3 // pin 16, Opamp reference -#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 - -#define LED_ENABLE_PIN PB0 // pin 19, Opamp power -#define LED_ENABLE_PORT PORTB // control port for PB0 - - -#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened -#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 -// pin to ADC mappings are in DS table 19-4 -#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 -// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 -#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D -// DS tables 19-3, 19-4 -// Bit 7 6 5 4 3 2 1 0 -// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 -// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 -// divided by ... -// REFS[1:0] = 1, 0 for internal 1.1V reference -// other bits reserved -#define ADMUX_VOLTAGE_DIVIDER 0b10000110 -#define ADC_PRSCL 0x07 // clk/128 - -// Raw ADC readings at 4.4V and 2.2V -// calibrate the voltage readout here -// estimated / calculated values are: -// (voltage - D1) * (R2/(R2+R1) * 256 / 1.1) -// D1, R1, R2 = 0, 330, 100 -#ifndef ADC_44 -//#define ADC_44 981 // raw value at 4.40V -#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 -#endif -#ifndef ADC_22 -//#define ADC_22 489 // raw value at 2.20V -#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead -inline void hwdef_setup() { - // enable output ports - // Opamp level and Opamp on/off - DDRB = (1 << PWM1_PIN) - | (1 << LED_ENABLE_PIN); - // aux R/G/B - DDRA = (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // WGM1[3:0]: 0,0,1,1: PWM, Phase Correct, 10-bit (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 0,0: PWM OC1B disabled (DS table 12-4) - TCCR1A = (1<