From 7cb4fe0944b839f28dfd96a88a772cd6a8b58019 Mon Sep 17 00:00:00 2001 From: Selene ToyKeeper Date: Thu, 2 Nov 2023 17:16:25 -0600 Subject: reorganized project files (part 1) (just moved files, didn't change the contents yet, and nothing will work without updating #includes and build scripts and stuff) --- hwdef-emisar-d4v2.h | 171 ---------------------------------------------------- 1 file changed, 171 deletions(-) delete mode 100644 hwdef-emisar-d4v2.h (limited to 'hwdef-emisar-d4v2.h') diff --git a/hwdef-emisar-d4v2.h b/hwdef-emisar-d4v2.h deleted file mode 100644 index 96c57a9..0000000 --- a/hwdef-emisar-d4v2.h +++ /dev/null @@ -1,171 +0,0 @@ -// hwdef for Emisar D4v2 (attiny1634) -// Copyright (C) 2018-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * Pin / Name / Function - * 1 PA6 FET PWM (direct drive) (PWM1B) - * 2 PA5 R: red aux LED (PWM0B) - * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED - * 5 PA2 e-switch - * 6 PA1 button LED - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 (none) PWM0A - * 16 PB3 7135 PWM (PWM1A) - * 17 PB2 MISO - * 18 PB1 MOSI - * 19 PB0 (none) - * 20 PA7 (none) - * ADC12 thermal sensor - */ - -#define ATTINY 1634 -#include - -#ifndef HWDEF_C_FILE -#define HWDEF_C_FILE hwdef-emisar-d4v2.c -#endif - -// allow using aux LEDs as extra channel modes -#include "chan-rgbaux.h" - -// channel modes: -// * 0. FET+7135 stacked -// * 1+. aux RGB -#define NUM_CHANNEL_MODES (1 + NUM_RGB_AUX_CHANNEL_MODES) -enum CHANNEL_MODES { - CM_MAIN = 0, - RGB_AUX_ENUMS -}; - -#define DEFAULT_CHANNEL_MODE CM_MAIN - -// right-most bit first, modes are in fedcba9876543210 order -#define CHANNEL_MODES_ENABLED 0b0000000000000001 -// no args -//#define USE_CHANNEL_MODE_ARGS -//#define CHANNEL_MODE_ARGS 0,0,0,0,0,0,0,0 - - -#define PWM_CHANNELS 2 // old, remove this - -#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255 -#define PWM_GET PWM_GET8 -#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255) -#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255 -#define PWM1_DATATYPE uint8_t // 1x7135 ramp -#define PWM2_DATATYPE uint8_t // DD FET ramp - -// PWM parameters of both channels are tied together because they share a counter -#define PWM_TOP ICR1 // holds the TOP value for for variable-resolution PWM -#define PWM_TOP_INIT 255 // highest value used in top half of ramp -#define PWM_CNT TCNT1 // for dynamic PWM, reset phase - -// 1x7135 channel -#define CH1_PIN PB3 // pin 16, 1x7135 PWM -#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3 - -// DD FET channel -#define CH2_PIN PA6 // pin 1, DD FET PWM -#define CH2_PWM OCR1B // OCR1B is the output compare register for PA6 - -// e-switch -#define SWITCH_PIN PA2 // pin 5 -#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC -#define SWITCH_PUE PUEA // pullup group A -#define PCINT_vect PCINT0_vect // ISR for PCINT[7:0] - - -#define ADC_PRSCL 0x07 // clk/128 - -// average drop across diode on this hardware -#ifndef VOLTAGE_FUDGE_FACTOR -#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V) -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -#define BUTTON_LED_PIN PA1 // pin 6 -#define BUTTON_LED_PORT PORTA // for all "PA" pins -#define BUTTON_LED_DDR DDRA // for all "PA" pins -#define BUTTON_LED_PUE PUEA // for all "PA" pins - -// this light has three aux LED channels: R, G, B -#define USE_AUX_RGB_LEDS -// it also has an independent LED in the button -#define USE_BUTTON_LED -// the aux LEDs are front-facing, so turn them off while main LEDs are on -#ifdef USE_INDICATOR_LED_WHILE_RAMPING -#undef USE_INDICATOR_LED_WHILE_RAMPING -#endif - - -inline void hwdef_setup() { - // enable output ports - // 7135 - DDRB = (1 << CH1_PIN); - // DD FET, aux R/G/B, button LED - DDRA = (1 << CH2_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (1<