From 0cc485438d75143e0d08757103dc4e5615caae51 Mon Sep 17 00:00:00 2001
From: Selene ToyKeeper
Date: Thu, 1 Apr 2021 18:59:11 -0600
Subject: Renamed gchart-fet1-t16 to t1616, to make it consistent with other
 t1616 models.

---
 hwdef-gchart-fet1-t16.h | 99 -------------------------------------------------
 1 file changed, 99 deletions(-)
 delete mode 100644 hwdef-gchart-fet1-t16.h

(limited to 'hwdef-gchart-fet1-t16.h')

diff --git a/hwdef-gchart-fet1-t16.h b/hwdef-gchart-fet1-t16.h
deleted file mode 100644
index e8fd11c..0000000
--- a/hwdef-gchart-fet1-t16.h
+++ /dev/null
@@ -1,99 +0,0 @@
-#ifndef HWDEF_GCH_FET1_T16_H
-#define HWDEF_GCH_FET1_T16_H
-
-/* gChart's custom FET+1 driver layout
-
-PB0 - PWM for FET (TCA - WO0)
-PB1 - PWM for 7135 (TCA - WO1)
-PB2 - Switch pin, internal pullup
-PB3 - Aux LED with 4700 Ohm series resistor
-Read voltage from VCC pin, has diode with ~0.4v drop
-
-*/
-
-
-#define LAYOUT_DEFINED
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define PWM_CHANNELS 2
-
-#ifndef SWITCH_PIN
-#define SWITCH_PIN     PIN2_bp    
-#define SWITCH_PORT    VPORTB.IN
-#define SWITCH_ISC_REG PORTB.PIN2CTRL
-#define SWITCH_VECT    PORTB_PORT_vect
-#define SWITCH_INTFLG  VPORTB.INTFLAGS
-#endif
-
-
-// 7135 channel
-#ifndef PWM1_PIN
-#define PWM1_PIN PB1               // 
-#define PWM1_LVL TCA0.SINGLE.CMP1  // CMP1 is the output compare register for PB1
-#endif
-
-// FET channel
-#ifndef PWM2_PIN
-#define PWM2_PIN PB0               // 
-#define PWM2_LVL TCA0.SINGLE.CMP0  // CMP0 is the output compare register for PB0
-#endif
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 8  // 4 = add 0.20V
-#endif
-
-
-// lighted button
-#ifndef AUXLED_PIN
-#define AUXLED_PIN  PIN3_bp
-#define AUXLED_PORT PORTB
-#endif
-
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
-
-	// set up the system clock to run at 5 MHz instead of the default 3.33 MHz
-	_PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_4X_gc | CLKCTRL_PEN_bm );
-
-    //VPORTA.DIR = 0b00000010;
-    VPORTB.DIR = PIN0_bm | PIN1_bm | PIN3_bm;
-    //VPORTC.DIR = 0b00000000;
-
-    // enable pullups on the input pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-    
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
-    PORTB.PIN2CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // switch
-    //PORTB.PIN3CTRL = PORT_PULLUPEN_bm; // Aux LED
-    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN5CTRL = PORT_PULLUPEN_bm;
-    
-    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-  
-  	// set up the PWM
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_WGMODE_SINGLESLOPE_gc;
-    TCA0.SINGLE.PER = 255;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
-}
-
-
-#endif
-- 
cgit v1.2.3