1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
// Hank Emisar/Noctigon Lume-X1 config options for Anduril
// Copyright (C) 2018-2024 Selene ToyKeeper, Loneoceans
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
// For flashlights using the Loneoceans Lume-X1-40W boost driver (AVR32DD20)
// - Same firmware for 6V, 9V, or 12V configs
// same as loneoceans lume-x1-avr32dd20 but with Hank-specific defaults
#define HWDEF_H hank/lume-x1/hwdef.h
#include "hank/anduril.h"
//***************************************
//** RAMP TABLE AND OPERATIONS **
//***************************************
#define RAMP_SIZE 150 // Change to 160 as well as table and values below if desired
// PWM1: DAC Data
// UDR x^4 curves specifically for Lume-X1 (AVR32DD20)
// levels 1 to 5:
// ./bin/level_calc.py 5.2 1 5 7135 100 0.01 0.1 --pwm 2500
// (with the last 2 values divided to fit)
// levels 6 to 150:
// ./bin/dac-scale.py $( ./bin/level_calc.py 5.3 1 145 7135 17 0.2 3000 --pwm 240000 | grep PWM1 | cut -d : -f 2- )
// top level for each "gear": 3 5 / 39 50 / 123 150
#define PWM1_LEVELS \
100, 359, 790, 588,1023, \
17, 21, 24, 29, 34, 39, 46, 54, 62, 71, 82, 94, 107, 122, 138, 157, 177, 199, 223, 250, 279, 311, 346, 385, 426, 471, 520, 573, 630, 692, 758, 830, 907, 990, \
441, 480, 522, 567, 615, 666, 720, 778, 840, 905, 974, \
26, 28, 30, 33, 35, 37, 40, 43, 46, 49, 52, 56, 59, 63, 67, 71, 76, 80, 85, 90, 96, 101, 107, 113, 120, 126, 133, 141, 148, 156, 165, 173, 182, 192, 202, 212, 222, 234, 245, 257, 269, 282, 296, 310, 324, 339, 355, 371, 387, 405, 422, 441, 460, 480, 501, 522, 544, 567, 590, 614, 640, 665, 692, 720, 748, 778, 808, 839, 872, 905, 939, 975,1011, \
429, 445, 461, 478, 495, 513, 531, 550, 570, 589, 610, 631, 653, 675, 698, 721, 745, 770, 795, 821, 848, 875, 903, 932, 962, 992,1023
#define PWM2_LEVELS \
V10, V10, V10, V25, V25, \
V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, \
V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, \
V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, V10, \
V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25, V25
#define LED_PATH1_PIN_LEVEL_MIN 1
#define LED_PATH2_PIN_LEVEL_MIN 6
#define LED_PATH3_PIN_LEVEL_MIN 51
#define HALFSPEED_LEVEL 20
#define QUARTERSPEED_LEVEL 10
#define DEFAULT_LEVEL 50
#define MAX_1x7135 49
#define RAMP_SMOOTH_FLOOR 1
#define RAMP_SMOOTH_CEIL 130
#define RAMP_DISCRETE_FLOOR 10
#define RAMP_DISCRETE_CEIL 130
#define RAMP_DISCRETE_STEPS 7
#define SIMPLE_UI_FLOOR 10
#define SIMPLE_UI_CEIL 110 // about ~12W
#define SIMPLE_UI_STEPS 5
// don't blink mid-ramp
#ifdef BLINK_AT_RAMP_MIDDLE
#undef BLINK_AT_RAMP_MIDDLE
#endif
//***************************************
//** THERMAL SETTINGS **
//***************************************
// stop panicking at 6W (not sure of this numbers yet since it depends on the host..)
#define THERM_FASTER_LEVEL 100 // about 6W
#define MIN_THERM_STEPDOWN 60 // similar to single amc7135 in a 3V light
//***************************************
//** AUX LEDs and MISC **
//***************************************
#define USE_BUTTON_LED
// this light has three aux LED channels: R, G, B
// (and some builds tie these also to a RGB side button)
#define USE_AUX_RGB_LEDS
#define USE_AUX_RGB_LEDS_WHILE_ON 25
#define USE_INDICATOR_LED_WHILE_RAMPING
// the aux LEDs are front-facing, so turn them off while main LEDs are on
//#ifdef USE_INDICATOR_LED_WHILE_RAMPING
//#undef USE_INDICATOR_LED_WHILE_RAMPING
//#endif
// show each channel while it scroll by in the menu
#define USE_CONFIG_COLORS
// blink numbers on the main LEDs by default (but allow user to change it)
#define DEFAULT_BLINK_CHANNEL CM_MAIN
// use aux red + aux blue for police strobe
#define USE_POLICE_COLOR_STROBE_MODE
#define POLICE_STROBE_USES_AUX
#define POLICE_COLOR_STROBE_CH1 CM_AUXRED
#define POLICE_COLOR_STROBE_CH2 CM_AUXBLU
#define PARTY_STROBE_ONTIME 1 // slow down party strobe
#define STROBE_OFF_LEVEL 1 // keep the regulator chips on between pulses
// smoother candle mode with bigger oscillations
#define CANDLE_AMPLITUDE 30 // default 25
// avr32dd20 has enough space to smooth out voltage readings
#define USE_VOLTAGE_LOWPASS
// enable long-blink as negative sign
#define USE_LONG_BLINK_FOR_NEGATIVE_SIGN
|
