added Emisar D4S V2 support

3 files changed, 197 insertions, 0 deletions

diff --git a/hwdef-Emisar_D4Sv2.h b/hwdef-Emisar_D4Sv2.h
new file mode 100644
index 0000000..8341e21
--- /dev/null
+++ b/hwdef-Emisar_D4Sv2.h
@@ -0,0 +1,124 @@
+#ifndef HWDEF_EMISAR_D4SV2_H
+#define HWDEF_EMISAR_D4SV2_H
+
+/* Emisar D4v2 driver layout (attiny1634)
+ * (same layout as D4v2, except it's a FET+3+1 instead of FET+1)
+ *
+ * Pin / Name / Function
+ *   1    PA6   FET PWM (PWM1B)
+ *   2    PA5   red aux LED (PWM0B)
+ *   3    PA4   green aux LED
+ *   4    PA3   blue aux LED
+ *   5    PA2   e-switch
+ *   6    PA1   (none)
+ *   7    PA0   (none)
+ *   8    GND   GND
+ *   9    VCC   VCC
+ *  10    PC5   (none)
+ *  11    PC4   (none)
+ *  12    PC3   RESET
+ *  13    PC2   (none)
+ *  14    PC1   SCK
+ *  15    PC0   3x7135 PWM (PWM0A)
+ *  16    PB3   1x7135 PWM (PWM1A)
+ *  17    PB2   MISO
+ *  18    PB1   MOSI
+ *  19    PB0   (none)
+ *  20    PA7   (none)
+ *      ADC12   thermal sensor
+ */
+
+#ifdef ATTINY
+#undef ATTINY
+#endif
+#define ATTINY 1634
+#include <avr/io.h>
+
+#define SWITCH_PIN   PA2    // pin 5
+#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt
+#define SWITCH_PCIE  PCIE0  // PCIE0 is for PCINT[7:0]
+#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
+#define SWITCH_PORT  PINA   // PINA or PINB or PINC
+
+#define PWM_CHANNELS 3
+
+#define PWM1_PIN PB3        // pin 16, 1x7135 PWM
+#define PWM1_LVL OCR1A      // OCR1A is the output compare register for PB3
+
+#define PWM2_PIN PC0        // pin 15, 3x7135 PWM
+#define PWM2_LVL OCR0A      // OCR0A is the output compare register for PC0
+
+#define PWM3_PIN PA6        // pin 1, FET PWM
+#define PWM3_LVL OCR1B      // OCR1B is the output compare register for PB1
+
+
+#define ADC_PRSCL   0x06    // clk/64
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 4  // add 0.20V  (measured 0.22V)
+#endif
+
+#define TEMP_CHANNEL 0b00001111
+
+// this light has aux LEDs under the optic
+#define AUXLED_R_PIN   PA5    // pin 2
+#define AUXLED_G_PIN   PA4    // pin 3
+#define AUXLED_B_PIN   PA3    // pin 4
+#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
+#define AUXLED_RGB_DDR DDRA   // DDRA or DDRB or DDRC
+#define AUXLED_RGB_PUE PUEA   // PUEA or PUEB or PUEC
+
+// with so many pins, doing this all with #ifdefs gets awkward...
+// ... so just hardcode it in each hwdef file instead
+inline void hwdef_setup() {
+  // enable output ports
+  // FET, aux R/G/B
+  DDRA = (1 << PWM3_PIN)
+       | (1 << AUXLED_R_PIN)
+       | (1 << AUXLED_G_PIN)
+       | (1 << AUXLED_B_PIN)
+       ;
+  // 1x7135
+  DDRB = (1 << PWM1_PIN);
+  // 3x7135
+  DDRC = (1 << PWM2_PIN);
+
+  // configure PWM
+  // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
+  // pre-scale for timer: N = 1
+  // WGM1[3:0]: 0,0,0,1: PWM, Phase Correct, 8-bit (DS table 12-5)
+  // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
+  // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
+  // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)
+  TCCR1A  = (0<<WGM11)  | (1<<WGM10)   // 8-bit (TOP=0xFF) (DS table 12-5)
+          | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
+          | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
+          ;
+  TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
+          | (0<<WGM13)  | (0<<WGM12)  // phase-correct PWM (DS table 12-5)
+          ;
+
+  // WGM0[2:0]: 0,0,1: PWM, Phase Correct (DS table 11-8)
+  // CS0[2:0]:  0,0,1: clk/1 (No prescaling) (DS table 11-9)
+  // COM0A[1:0]:  1,0: PWM OC0A in the normal direction (DS table 11-4)
+  // COM0B[1:0]:  0,0: OC0B disabled (DS table 11-7)
+  // TCCR0A: COM0A1, COM0A0, COM0B1, COM0B0, -, -, WGM01, WGM00
+  TCCR0A  = (0<<WGM01)  | (1<<WGM00)   // PWM, Phase Correct, TOP=0xFF (DS table 11-5)
+          | (1<<COM1A1) | (0<<COM1A0)  // PWM 0A in normal direction (DS table 11-4)
+          | (0<<COM1B1) | (0<<COM1B0)  // PWM 0B disabled (DS table 11-7)
+          ;
+  // TCCR0B: FOC0A, FOC0B, -, -, WGM02, CS02, CS01, CS00
+  TCCR0B  = (0<<CS02)   | (0<<CS01) | (1<<CS00)  // clk/1 (no prescaling) (DS table 11-9)
+          | (0<<WGM02)  // PWM, Phase Correct, TOP=0xFF (DS table 11-8)
+          ;
+
+  // set up e-switch
+  //PORTA = (1 << SWITCH_PIN);  // TODO: configure PORTA / PORTB / PORTC?
+  PUEA = (1 << SWITCH_PIN);  // pull-up for e-switch
+  SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
+}
+
+#define LAYOUT_DEFINED
+
+#endif
diff --git a/spaghetti-monster/anduril/cfg-emisar-d4sv2-219.h b/spaghetti-monster/anduril/cfg-emisar-d4sv2-219.h
new file mode 100644
index 0000000..9898246
--- /dev/null
+++ b/spaghetti-monster/anduril/cfg-emisar-d4sv2-219.h
@@ -0,0 +1,10 @@
+// Emisar D4Sv2-219 config options for Anduril
+#include "cfg-emisar-d4sv2.h"
+// ATTINY: 1634
+
+#undef PWM1_LEVELS
+#undef PWM2_LEVELS
+#undef PWM3_LEVELS
+#define PWM1_LEVELS 1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,17,18,19,20,21,22,24,26,28,30,33,35,38,41,44,47,50,54,57,61,65,69,74,79,84,89,94,100,106,113,119,126,134,142,150,158,167,176,186,196,207,218,230,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,12,16,21,25,30,35,41,46,52,58,64,71,77,84,92,99,107,115,124,133,142,151,161,172,182,193,205,217,229,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+#define PWM3_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,2,3,4,6,7,9,10,12,13,15,17,18,20,22,24,26,28,30,33,35,37,40,43,45,48,50,53,56,59,62,65,69,72,76,80,83,87,91,95,99,104,108,113,117,123,127,132,138,143,148,154,160,166,172,178,185,192
diff --git a/spaghetti-monster/anduril/cfg-emisar-d4sv2.h b/spaghetti-monster/anduril/cfg-emisar-d4sv2.h
new file mode 100644
index 0000000..acc9101
--- /dev/null
+++ b/spaghetti-monster/anduril/cfg-emisar-d4sv2.h
@@ -0,0 +1,63 @@
+// Emisar D4S V2 config options for Anduril
+#include "hwdef-Emisar_D4Sv2.h"
+// ATTINY: 1634
+
+// this light has three aux LED channels: R, G, B
+#define USE_AUX_RGB_LEDS
+// the aux LEDs are front-facing, so turn them off while main LEDs are on
+#ifdef USE_INDICATOR_LED_WHILE_RAMPING
+#undef USE_INDICATOR_LED_WHILE_RAMPING
+#endif
+// enable blinking aux LEDs
+#define TICK_DURING_STANDBY
+#define STANDBY_TICK_SPEED 3  // every 0.128 s
+//#define STANDBY_TICK_SPEED 4  // every 0.256 s
+//#define STANDBY_TICK_SPEED 5  // every 0.512 s
+
+
+// 1x7135 + 3x7135 + FET
+// ../../../bin/level_calc.py seventh 3 150 7135 1 2.3 130 7135 11 5 400.1 FET 2 10 4000
+// (and some manual edits to make the clock speed changes smoother)
+#define PWM1_LEVELS 1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,17,18,19,20,21,22,24,26,28,30,33,35,38,41,44,47,50,54,57,61,65,69,74,79,84,89,94,100,106,113,119,126,134,142,150,158,167,176,186,196,207,218,230,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,12,16,21,25,30,35,41,46,52,58,64,71,77,84,92,99,107,115,124,133,142,151,161,172,182,193,205,217,229,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+#define PWM3_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,3,5,6,8,10,12,14,16,18,20,23,25,27,30,32,35,38,41,44,47,50,53,57,60,64,67,71,75,79,83,87,92,96,101,106,111,116,121,127,132,138,144,150,156,163,169,176,183,190,197,205,213,221,229,237,246,255
+#define MAX_1x7135 62
+#define MAX_Nx7135 93
+#define HALFSPEED_LEVEL 18
+#define QUARTERSPEED_LEVEL 8
+
+#define RAMP_SMOOTH_FLOOR 1
+#define RAMP_SMOOTH_CEIL 130
+// 20, 38, 56, 75, [93], 111, 130
+#define RAMP_DISCRETE_FLOOR 20
+#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
+#define RAMP_DISCRETE_STEPS 7
+
+#define DEFAULT_LEVEL MAX_Nx7135
+#define STROBE_BRIGHTNESS MAX_LEVEL
+
+#define MUGGLE_FLOOR RAMP_DISCRETE_FLOOR
+#define MUGGLE_CEILING MAX_Nx7135
+
+// stop panicking at ~50% power or ~2000 lm
+#define THERM_FASTER_LEVEL 130
+
+// no need to be extra-careful on this light
+#ifdef THERM_HARD_TURBO_DROP
+#undef THERM_HARD_TURBO_DROP
+#endif
+
+// respond to thermal changes faster
+#define THERMAL_WARNING_SECONDS 3
+#define THERMAL_UPDATE_SPEED 2
+#define THERM_PREDICTION_STRENGTH 4
+
+// easier access to thermal config mode, for Emisar
+#define USE_TENCLICK_THERMAL_CONFIG
+
+#ifdef BLINK_AT_RAMP_MIDDLE
+#undef BLINK_AT_RAMP_MIDDLE
+#endif
+
+// seems relevant on attiny1634
+#define THERM_CAL_OFFSET 5