moved variant builds under their parent, like "d4-219" -> "d4/219"

2 files changed, 0 insertions, 284 deletions

diff --git a/hw/hank/noctigon-k1-boost/anduril.h b/hw/hank/noctigon-k1-boost/anduril.h
deleted file mode 100644
index e18a015..0000000
--- a/hw/hank/noctigon-k1-boost/anduril.h
+++ /dev/null
@@ -1,96 +0,0 @@
-// Noctigon K1 boost config options for Anduril
-// Copyright (C) 2019-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-#define MODEL_NUMBER "0253"
-#include "hank/noctigon-k1-boost/hwdef.h"
-#include "hank/anduril.h"
-// ATTINY: 1634
-
-// Most K1 lights can run hotter than default, but the 12V model
-// is known to have issues with the driver itself getting too hot.
-// This then causes the main LEDs to turn off during use, because the
-// boost chip's built-in protection activates.  So try to keep the
-// temperature relatively low.
-#undef DEFAULT_THERM_CEIL
-#define DEFAULT_THERM_CEIL 45
-
-// this light has three aux LED channels: R, G, B
-#define USE_AUX_RGB_LEDS
-#define USE_AUX_RGB_LEDS_WHILE_ON  25
-#define USE_INDICATOR_LED_WHILE_RAMPING
-
-#if 0  // old, 10-bit PWM method
-// level_calc.py cube 1 150 7135 0 4 1300
-// (with max_pwm set to 1023)
-// (level 0 is usable on this light)
-#define RAMP_LENGTH 150
-#define PWM1_LEVELS 0,0,1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,14,15,16,17,19,20,22,23,25,26,28,30,31,33,35,37,39,42,44,46,48,51,53,56,59,61,64,67,70,73,76,80,83,86,90,94,97,101,105,109,113,117,122,126,130,135,140,144,149,154,159,165,170,175,181,187,193,198,204,211,217,223,230,236,243,250,257,264,271,279,286,294,302,310,318,326,334,343,351,360,369,378,387,397,406,416,426,436,446,456,466,477,488,499,510,521,532,544,555,567,579,591,604,616,629,642,655,668,682,695,709,723,737,751,766,780,795,810,825,841,856,872,888,904,921,937,954,971,988,1005,1023
-#define MAX_1x7135 50
-// don't slow down at low levels; this isn't that sort of light
-// (it needs to stay at full speed for the 10-bit PWM to work)
-#ifdef USE_DYNAMIC_UNDERCLOCKING
-#undef USE_DYNAMIC_UNDERCLOCKING
-#endif
-#endif
-
-#define RAMP_SIZE 150
-// delta-sigma modulated PWM (0b0HHHHHHHHLLLLLLL = 0, 8xHigh, 7xLow bits)
-// level_calc.py 5.01 1 150 7135 0 0.2 2000 --pwm 32640
-// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM)
-#define PWM1_LEVELS 0,1,2,3,4,5,6,7,9,10,12,14,17,19,22,25,28,32,36,41,45,50,56,62,69,76,84,92,101,110,121,132,143,156,169,184,199,215,232,251,270,291,313,336,360,386,414,442,473,505,539,574,612,651,693,736,782,829,880,932,987,1045,1105,1168,1233,1302,1374,1449,1527,1608,1693,1781,1873,1969,2068,2172,2279,2391,2507,2628,2753,2883,3018,3158,3303,3454,3609,3771,3938,4111,4289,4475,4666,4864,5068,5280,5498,5724,5957,6197,6445,6701,6965,7237,7518,7808,8106,8413,8730,9056,9392,9737,10093,10459,10835,11223,11621,12031,12452,12884,13329,13786,14255,14737,15232,15741,16262,16798,17347,17911,18489,19082,19691,20314,20954,21609,22281,22969,23674,24397,25137,25895,26671,27465,28279,29111,29963,30835,31727,32640
-#define MIN_THERM_STEPDOWN 50
-#define DEFAULT_LEVEL 70
-#define MAX_1x7135 150
-// always run at 1/4th speed, because 4 kHz PWM is enough for this circuit
-// and speed changes make a big visible bump
-#define HALFSPEED_LEVEL     255
-#define QUARTERSPEED_LEVEL  255
-
-#define RAMP_SMOOTH_FLOOR 1
-#define RAMP_SMOOTH_CEIL  130
-// 10, 30, 50, [70], 90, 110, 130
-#define RAMP_DISCRETE_FLOOR 10
-#define RAMP_DISCRETE_CEIL  RAMP_SMOOTH_CEIL
-#define RAMP_DISCRETE_STEPS 7
-
-// safe limit ~50% power
-#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR
-#define SIMPLE_UI_CEIL 120
-#define SIMPLE_UI_STEPS 5
-
-// stop panicking at ~70% power or ~600 lm
-#define THERM_FASTER_LEVEL 130
-
-#define THERM_CAL_OFFSET 5
-
-#define THERM_RESPONSE_MAGNITUDE 32  // smaller adjustments, this host changes temperature slowly
-#define THERM_NEXT_WARNING_THRESHOLD 32  // more error tolerance before adjusting
-
-// show each channel while it scroll by in the menu
-#define USE_CONFIG_COLORS
-
-// blink numbers on the main LEDs by default (but allow user to change it)
-#define DEFAULT_BLINK_CHANNEL  CM_MAIN
-
-// slow down party strobe; this driver can't pulse for 1ms or less
-#define PARTY_STROBE_ONTIME 4
-
-// use aux red + aux blue for police strobe
-#define USE_POLICE_COLOR_STROBE_MODE
-#define POLICE_STROBE_USES_AUX
-#define POLICE_COLOR_STROBE_CH1        CM_AUXRED
-#define POLICE_COLOR_STROBE_CH2        CM_AUXBLU
-
-// make candle mode wobble more
-#define CANDLE_AMPLITUDE 33
-
-// the entire ramp is regulated; don't blink halfway up
-#ifdef BLINK_AT_RAMP_MIDDLE
-#undef BLINK_AT_RAMP_MIDDLE
-#endif
-
-// added for convenience
-#define USE_SOFT_FACTORY_RESET
-
diff --git a/hw/hank/noctigon-k1-boost/hwdef.h b/hw/hank/noctigon-k1-boost/hwdef.h
deleted file mode 100644
index 1c6a06d..0000000
--- a/hw/hank/noctigon-k1-boost/hwdef.h
+++ /dev/null
@@ -1,188 +0,0 @@
-// Noctigon K1 12V driver layout (attiny1634)
-// Copyright (C) 2019-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * Pin / Name / Function
- *   1    PA6   (none) (PWM1B) (reserved for DD drivers)
- *   2    PA5   R: red aux LED (PWM0B)
- *   3    PA4   G: green aux LED
- *   4    PA3   B: blue aux LED
- *   5    PA2   (none) (reserved for L: button LED (on some models))
- *   6    PA1   (none)
- *   7    PA0   (none)
- *   8    GND   GND
- *   9    VCC   VCC
- *  10    PC5   (none)
- *  11    PC4   (none)
- *  12    PC3   RESET
- *  13    PC2   (none)
- *  14    PC1   SCK
- *  15    PC0   boost PMIC enable (PWM0A not used)
- *  16    PB3   main LED PWM (PWM1A)
- *  17    PB2   MISO
- *  18    PB1   MOSI / battery voltage (ADC6)
- *  19    PB0   Opamp power
- *  20    PA7   e-switch  (PCINT7)
- *      ADC12   thermal sensor
- *
- * Main LED power uses one pin to turn the Opamp on/off,
- * and one pin to control Opamp power level.
- * Regulated brightness control uses the power level pin, with PWM+DSM.
- * The on/off pin is only used to turn the main LED on and off,
- * not to change brightness.
- */
-
-#define ATTINY 1634
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hank/noctigon-dm11-boost/hwdef.c
-
-// allow using aux LEDs as extra channel modes
-#include "fsm/chan-rgbaux.h"
-
-// channel modes:
-// * 0. main LEDs
-// * 1+. aux RGB
-#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
-enum CHANNEL_MODES {
-    CM_MAIN = 0,
-    RGB_AUX_ENUMS
-};
-
-#define DEFAULT_CHANNEL_MODE  CM_MAIN
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b0000000000000001
-// no args
-//#define USE_CHANNEL_MODE_ARGS
-//#define CHANNEL_MODE_ARGS     0,0,0,0,0,0,0,0
-
-
-#define PWM_CHANNELS  1  // old, remove this
-
-#define PWM_BITS      16        // 0 to 32640 (0 to 255 PWM + 0 to 127 DSM) at constant kHz
-#define PWM_GET       PWM_GET16
-#define PWM_DATATYPE  uint16_t
-#define PWM_DATATYPE2 uint32_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint16_t  // 15-bit PWM+DSM ramp
-
-#define PWM_TOP       ICR1   // holds the TOP value for variable-resolution PWM
-#define PWM_TOP_INIT  255
-#define PWM_CNT       TCNT1  // for checking / resetting phase
-// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM)
-#define DSM_TOP       (255<<7) // 15-bit resolution leaves 1 bit for carry
-
-// timer interrupt for DSM
-#define DSM_vect     TIMER1_OVF_vect
-#define DSM_INTCTRL  TIMSK
-#define DSM_OVF_bm   (1<<TOIE1)
-
-#define DELAY_FACTOR 90  // less time in delay() because more time spent in interrupts
-
-// regulated channel
-uint16_t ch1_dsm_lvl;
-uint8_t ch1_pwm, ch1_dsm;
-#define CH1_PIN          PB3    // pin 16, Opamp reference
-#define CH1_PWM          OCR1A  // OCR1A is the output compare register for PB3
-
-#define CH1_ENABLE_PIN   PB0    // pin 19, Opamp power
-#define CH1_ENABLE_PORT  PORTB  // control port for PB0
-
-#define CH1_ENABLE_PIN2  PC0   // pin 15, boost PMIC enable
-#define CH1_ENABLE_PORT2 PORTC // control port for PC0
-
-// e-switch
-#define SWITCH_PIN   PA7     // pin 20
-#define SWITCH_PCINT PCINT7  // pin 20 pin change interrupt
-#define SWITCH_PCIE  PCIE0   // PCIE0 is for PCINT[7:0]
-#define SWITCH_PCMSK PCMSK0  // PCMSK0 is for PCINT[7:0]
-#define SWITCH_PORT  PINA    // PINA or PINB or PINC
-#define SWITCH_PUE   PUEA    // pullup group A
-#define PCINT_vect   PCINT0_vect  // ISR for PCINT[7:0]
-
-#define USE_VOLTAGE_DIVIDER  // use a dedicated pin, not VCC, because VCC input is flattened
-#define VOLTAGE_PIN PB1      // Pin 18 / PB1 / ADC6
-// pin to ADC mappings are in DS table 19-4
-#define VOLTAGE_ADC      ADC6D  // digital input disable pin for PB1
-// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6
-#define VOLTAGE_ADC_DIDR DIDR1  // DIDR channel for ADC6D
-// DS tables 19-3, 19-4
-// Bit   7     6     5      4     3    2    1    0
-//     REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0
-// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1
-// divided by ...
-// REFS[1:0] = 1, 0 for internal 1.1V reference
-// other bits reserved
-#define ADMUX_VOLTAGE_DIVIDER 0b10000110
-#define ADC_PRSCL   0x07    // clk/128
-
-// Raw ADC readings at 4.4V and 2.2V
-// calibrate the voltage readout here
-// estimated / calculated values are:
-//   (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
-// D1, R1, R2 = 0, 330, 100
-#ifndef ADC_44
-//#define ADC_44 981  // raw value at 4.40V
-#define ADC_44 967  // manually tweaked so 4.16V will blink out 4.2
-#endif
-#ifndef ADC_22
-//#define ADC_22 489  // raw value at 2.20V
-#define ADC_22 482  // manually tweaked so 4.16V will blink out 4.2
-#endif
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN    PA5    // pin 2
-#define AUXLED_G_PIN    PA4    // pin 3
-#define AUXLED_B_PIN    PA3    // pin 4
-#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC
-
-inline void hwdef_setup() {
-    // enable output ports
-    // boost PMIC on/off
-    DDRC = (1 << CH1_ENABLE_PIN2);
-    // Opamp level and Opamp on/off
-    DDRB = (1 << CH1_PIN)
-         | (1 << CH1_ENABLE_PIN);
-    // aux R/G/B
-    DDRA = (1 << AUXLED_R_PIN)
-         | (1 << AUXLED_G_PIN)
-         | (1 << AUXLED_B_PIN)
-         ;
-
-    // configure PWM
-    // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-    // pre-scale for timer: N = 1
-    // PWM for both channels
-    // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
-    // WGM1[3:0]: 1,1,1,0: PWM, Fast, adjustable (DS table 12-5)
-    // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
-    // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
-    // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)
-    TCCR1A = (1<<WGM11)  | (0<<WGM10)   // adjustable PWM (TOP=ICR1) (DS table 12-5)
-           | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-           | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
-           ;
-    TCCR1B = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-           //| (1<<WGM13)  | (1<<WGM12)  // fast adjustable PWM (DS table 12-5)
-           | (1<<WGM13)  | (0<<WGM12)  // phase-correct adjustable PWM (DS table 12-5)
-           ;
-
-    // set PWM resolution
-    PWM_TOP = PWM_TOP_INIT;
-
-    // set up interrupt for delta-sigma modulation
-    // (moved to hwdef.c functions so it can be enabled/disabled based on ramp level)
-    //DSM_INTCTRL |= DSM_OVF_bm;  // interrupt once for each timer cycle
-
-    // set up e-switch
-    SWITCH_PUE = (1 << SWITCH_PIN);  // pull-up for e-switch
-    SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
-}
-
-
-#define LAYOUT_DEFINED
-