added wurkkos-ts25-boost (early version made from spec, no clue if it works)

1 files changed, 174 insertions, 0 deletions

diff --git a/hw/wurkkos/ts25/boost/hwdef.h b/hw/wurkkos/ts25/boost/hwdef.h
new file mode 100644
index 0000000..42a4f28
--- /dev/null
+++ b/hw/wurkkos/ts25/boost/hwdef.h
@@ -0,0 +1,174 @@
+// Wurkkos TS25 driver layout
+// Copyright (C) 2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/* Boost driver based on MP3432 and attiny1616
+ * with high dynamic range and DAC control, AUX : RGB + button
+ * hardware version : 2.0+
+ * compatible with BST20-FWxA v1.0 (no button LED A)
+ *
+ * Pin / Name / Function
+ *   1    PA2   -
+ *   2    PA3   -
+ *   3    GND   GND
+ *   4    VCC   VCC
+ *   5    PA4   -
+ *   6    PA5   e-switch
+ *   7    PA6   -
+ *   8    PA7   -
+ *   9    PB5   -
+ *  10    PB4   -
+ *  11    PB3   -
+ *  12    PB2   EN: boost enable
+ *  13    PB1   -
+ *  14    PB0   PWM
+ *  15    PC0   -
+ *  16    PC1   B: aux blue
+ *  17    PC2   G: aux green
+ *  18    PC3   R: aux red
+ *  19    PA0   UDPI
+ *  20    PA1   Vbat sense (voltage divider)
+ *
+ */
+
+#define HWDEF_C  wurkkos/ts25/boost/hwdef.c
+
+// allow using aux LEDs as extra channel modes
+#include "fsm/chan-rgbaux.h"
+
+// channel modes:
+// * 0. main LEDs
+// * 1+. aux RGB
+#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
+enum CHANNEL_MODES {
+    CM_MAIN = 0,
+    RGB_AUX_ENUMS
+};
+
+#define DEFAULT_CHANNEL_MODE  CM_MAIN
+
+// right-most bit first, modes are in fedcba9876543210 order
+#define CHANNEL_MODES_ENABLED 0b0000000000000001
+
+
+#define PWM_BITS      16        // 0 to 32640 (0 to 255 PWM + 0 to 127 DSM) at constant kHz
+#define PWM_GET       PWM_GET16
+#define PWM_DATATYPE  uint16_t
+#define PWM_DATATYPE2 uint32_t  // only needs 32-bit if ramp values go over 255
+#define PWM1_DATATYPE uint16_t  // 15-bit PWM+DSM ramp
+
+#define PWM_TOP  TCA0.SINGLE.PERBUF  // holds the TOP value for for variable-resolution PWM
+#define PWM_TOP_INIT  255
+#define PWM_CNT  TCA0.SINGLE.CNT  // for checking / resetting phase
+// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM)
+#define DSM_TOP       (255<<7) // 15-bit resolution leaves 1 bit for carry
+
+// timer interrupt for DSM
+#define DSM_vect     TCA0_OVF_vect
+#define DSM_INTCTRL  TCA0.SINGLE.INTCTRL
+#define DSM_INTFLAGS TCA0.SINGLE.INTFLAGS
+#define DSM_OVF_bm   TCA_SINGLE_OVF_bm
+
+#define DELAY_FACTOR 90  // less time in delay() because more time spent in interrupts
+
+// regulated channel
+uint16_t ch1_dsm_lvl;
+uint8_t ch1_pwm, ch1_dsm;
+#define CH1_PIN  PB0
+#define CH1_PWM  TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
+
+#define CH1_ENABLE_PIN   PIN2_bp
+#define CH1_ENABLE_PORT  PORTB_OUT
+
+// e-switch
+#define SWITCH_PIN      PIN5_bp
+#define SWITCH_PORT     VPORTA.IN
+#define SWITCH_ISC_REG  PORTA.PIN2CTRL
+#define SWITCH_VECT     PORTA_PORT_vect
+#define SWITCH_INTFLG   VPORTA.INTFLAGS
+
+// Voltage divider battLVL
+#define USE_VOLTAGE_DIVIDER       // use a dedicated pin, not VCC, because VCC input is regulated
+#define ADMUX_VOLTAGE_DIVIDER  ADC_MUXPOS_AIN1_gc  // which ADC channel to read
+// don't use the default VDD converter
+#undef voltage_raw2cooked
+#define voltage_raw2cooked  mcu_vdivider_raw2cooked
+
+// Raw ADC readings at 4.4V and 2.2V
+// calibrate the voltage readout here
+// estimated / calculated values are:
+//   (voltage - D1) * (R2/(R2+R1) * 4096 / 1.1)
+// Resistors are 330k and 100k
+#define ADC_44  3810  // raw value at 4.40V
+#define ADC_22  1905  // raw value at 2.20V
+
+// this light has aux LEDs under the optic
+#define AUXLED_R_PIN    PIN3_bp    // pin 3
+#define AUXLED_G_PIN    PIN2_bp    // pin 2
+#define AUXLED_B_PIN    PIN1_bp    // pin 1
+#define AUXLED_RGB_PORT PORTC  // PORTA or PORTB or PORTC
+
+// this light has three aux LED channels: R, G, B
+#define USE_AUX_RGB_LEDS
+
+
+inline void hwdef_setup() {
+
+    mcu_clock_speed();
+
+    // Outputs:
+    //VPORTA.DIR = ...;
+    VPORTB.DIR = PIN0_bm   // PWM
+               | PIN2_bm;  // boost enable
+    VPORTC.DIR = PIN1_bm   // aux B
+               | PIN2_bm   // aux G
+               | PIN3_bm;  // aux R
+
+    // enable pullups on the unused pins to reduce power
+    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
+    //PORTA.PIN1CTRL = PORT_PULLUPEN_bm;  // Vbat sense
+    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
+    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
+
+    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm;  // regulated channel
+    PORTB.PIN1CTRL = PORT_PULLUPEN_bm;
+    //PORTB.PIN2CTRL = PORT_PULLUPEN_bm;  // boost enable
+    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN5CTRL = PORT_PULLUPEN_bm;
+
+    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
+    //PORTC.PIN1CTRL = PORT_PULLUPEN_bm;  // RGB Aux
+    //PORTC.PIN2CTRL = PORT_PULLUPEN_bm;  // RGB Aux
+    //PORTC.PIN3CTRL = PORT_PULLUPEN_bm;  // RGB Aux
+
+    // set up the PWM
+    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
+    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
+    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
+    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
+    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
+    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
+    // See the manual for other pins, clocks, configs, portmux, etc
+    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm
+                      //| TCA_SINGLE_CMP1EN_bm
+                      | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
+    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc
+                      | TCA_SINGLE_ENABLE_bm;
+
+    PWM_TOP = PWM_TOP_INIT;
+
+    // set up interrupt for delta-sigma modulation
+    // (moved to hwdef.c functions so it can be enabled/disabled based on ramp level)
+    //DSM_INTCTRL |= DSM_OVF_bm;  // interrupt once for each timer cycle
+
+}
+
+
+#define LAYOUT_DEFINED
+