converted noctigon-kr4-boost to new API

(it's almost identical to noctigon-dm11-boost)

1 files changed, 0 insertions, 158 deletions

diff --git a/hwdef-Noctigon_KR4-12V.h b/hwdef-Noctigon_KR4-12V.h
deleted file mode 100644
index 57d39f2..0000000
--- a/hwdef-Noctigon_KR4-12V.h
+++ /dev/null
@@ -1,158 +0,0 @@
-// Noctigon KR4 (12V) driver layout (attiny1634)
-// Copyright (C) 2020-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * (based on Noctigon DM11-12V and KR4)
- *
- * Pin / Name / Function
- *   1    PA6   (none) (PWM1B) (reserved for DD drivers)
- *   2    PA5   R: red aux LED (PWM0B)
- *   3    PA4   G: green aux LED
- *   4    PA3   B: blue aux LED
- *   5    PA2   L: button LED
- *   6    PA1   (none)
- *   7    PA0   (none)
- *   8    GND   GND
- *   9    VCC   VCC
- *  10    PC5   (none)
- *  11    PC4   (none)
- *  12    PC3   RESET
- *  13    PC2   (none)
- *  14    PC1   SCK
- *  15    PC0   boost PMIC enable (PWM0A not used)
- *  16    PB3   main LED PWM (PWM1A)
- *  17    PB2   MISO / e-switch (PCINT10)
- *  18    PB1   MOSI / battery voltage (ADC6)
- *  19    PB0   Opamp power
- *  20    PA7   (none)  (PCINT7)
- *      ADC12   thermal sensor
- *
- * Main LED power uses one pin to turn the Opamp on/off,
- * and one pin to control Opamp power level.
- * Linear brightness control uses the power level pin, with dynamic PWM.
- * The on/off pin is only used to turn the main LED on and off,
- * not to change brightness.
- */
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1634
-#include <avr/io.h>
-
-#define PWM_CHANNELS 1  // can't use DD FET on boost drivers
-#define PWM_BITS 16  // data type needs 16 bits, not 8
-#define PWM_TOP  255 // highest value used in top half of ramp
-#define USE_DYN_PWM  // dynamic frequency and speed
-
-#define SWITCH_PIN   PB2     // pin 17
-#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt
-#define SWITCH_PCIE  PCIE1   // PCIE1 is for PCINT[11:8]
-#define SWITCH_PCMSK PCMSK1  // PCMSK1 is for PCINT[11:8]
-#define SWITCH_PORT  PINB    // PINA or PINB or PINC
-#define PCINT_vect   PCINT1_vect  // ISR for PCINT[11:8]
-
-#define PWM1_PIN PB3        // pin 16, Opamp reference
-#define PWM1_LVL OCR1A      // OCR1A is the output compare register for PB3
-#define PWM1_CNT TCNT1      // for dynamic PWM, reset phase
-#define PWM1_PHASE_RESET_OFF  // force reset while shutting off
-#define PWM1_PHASE_RESET_ON   // force reset while turning on
-#define PWM1_PHASE_SYNC       // manual sync while changing level
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM1_TOP ICR1       // holds the TOP value for for variable-resolution PWM
-
-#define LED_ENABLE_PIN  PB0    // pin 19, Opamp power
-#define LED_ENABLE_PORT PORTB  // control port for PB0
-
-#define LED2_ENABLE_PIN  PC0    // pin 15, boost PMIC enable
-#define LED2_ENABLE_PORT PORTC  // control port for PC0
-
-
-#define USE_VOLTAGE_DIVIDER  // use a dedicated pin, not VCC, because VCC input is flattened
-#define VOLTAGE_PIN PB1      // Pin 18 / PB1 / ADC6
-// pin to ADC mappings are in DS table 19-4
-#define VOLTAGE_ADC      ADC6D  // digital input disable pin for PB1
-// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6
-#define VOLTAGE_ADC_DIDR DIDR1  // DIDR channel for ADC6D
-// DS tables 19-3, 19-4
-// Bit   7     6     5      4     3    2    1    0
-//     REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0
-// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1
-// divided by ...
-// REFS[1:0] = 1, 0 for internal 1.1V reference
-// other bits reserved
-#define ADMUX_VOLTAGE_DIVIDER 0b10000110
-#define ADC_PRSCL   0x07    // clk/128
-
-// Raw ADC readings at 4.4V and 2.2V
-// calibrate the voltage readout here
-// estimated / calculated values are:
-//   (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
-// D1, R1, R2 = 0, 330, 100
-#ifndef ADC_44
-//#define ADC_44 981  // raw value at 4.40V
-#define ADC_44 967  // manually tweaked so 4.16V will blink out 4.2
-#endif
-#ifndef ADC_22
-//#define ADC_22 489  // raw value at 2.20V
-#define ADC_22 482  // manually tweaked so 4.16V will blink out 4.2
-#endif
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN    PA5    // pin 2
-#define AUXLED_G_PIN    PA4    // pin 3
-#define AUXLED_B_PIN    PA3    // pin 4
-#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC
-
-#define BUTTON_LED_PIN  PA2    // pin 5
-#define BUTTON_LED_PORT PORTA  // for all "PA" pins
-#define BUTTON_LED_DDR  DDRA   // for all "PA" pins
-#define BUTTON_LED_PUE  PUEA   // for all "PA" pins
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
-  // enable output ports
-  // boost PMIC on/off
-  DDRC = (1 << LED2_ENABLE_PIN);
-  // Opamp level and Opamp on/off
-  DDRB = (1 << PWM1_PIN)
-       | (1 << LED_ENABLE_PIN);
-  // aux R/G/B, button LED
-  DDRA = (1 << AUXLED_R_PIN)
-       | (1 << AUXLED_G_PIN)
-       | (1 << AUXLED_B_PIN)
-       | (1 << BUTTON_LED_PIN)
-       ;
-
-  // configure PWM
-  // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-  // pre-scale for timer: N = 1
-  // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
-  // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
-  // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
-  // COM1B[1:0]:    0,0: PWM OC1B disabled (DS table 12-4)
-  TCCR1A  = (1<<WGM11)  | (0<<WGM10)   // adjustable PWM (TOP=ICR1) (DS table 12-5)
-          | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-          | (0<<COM1B1) | (0<<COM1B0)  // PWM 1B disabled (DS table 12-4)
-          ;
-  TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-          | (1<<WGM13)  | (0<<WGM12)  // phase-correct adjustable PWM (DS table 12-5)
-          ;
-
-  // set PWM resolution
-  PWM1_TOP = PWM_TOP;
-
-  // set up e-switch
-  //PORTB = (1 << SWITCH_PIN);  // TODO: configure PORTA / PORTB / PORTC?
-  PUEB = (1 << SWITCH_PIN);  // pull-up for e-switch
-  SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
-}
-
-#define LAYOUT_DEFINED
-