merging gchart's changes, part 1...

+ added Sofirn LT1S Pro
+ added Sofirn SC21 Pro
+ added Wurkkos TS10
+ added Wurkkos TS25
* small changes to other models
* improved dual voltage support
+ added attiny1616 flashing python script w/ pymcuprog

These changes are incomplete.  It does not yet include:
- extended simple UI
- t1616 WDT reset detection
- gchart's OUTPUT_MUX code (I plan to rewrite the entire tint system)

1 files changed, 117 insertions, 0 deletions

diff --git a/hwdef-Wurkkos_TS10.h b/hwdef-Wurkkos_TS10.h
new file mode 100644
index 0000000..6cfe050
--- /dev/null
+++ b/hwdef-Wurkkos_TS10.h
@@ -0,0 +1,117 @@
+#ifndef HWDEF_BLF_Q8_T1616_H
+#define HWDEF_BLF_Q8_T1616_H
+
+/* BLF Q8 driver layout using the Attiny1616
+
+Driver pinout:
+ * eSwitch:    PA5
+ * Aux LED:    PB5
+ * PWM FET:    PB0 (TCA0 WO0)
+ * PWM 1x7135: PB1 (TCA0 WO1)
+ * Voltage:    VCC
+
+*/
+
+
+#define LAYOUT_DEFINED
+
+#ifdef ATTINY
+#undef ATTINY
+#endif
+#define ATTINY 1616
+#include <avr/io.h>
+
+#define PWM_CHANNELS 2
+#define PWM_BITS 16
+#define PWM_TOP 255
+#define USE_DYN_PWM
+
+#ifndef SWITCH_PIN
+#define SWITCH_PIN     PIN5_bp
+#define SWITCH_PORT    VPORTA.IN
+#define SWITCH_ISC_REG PORTA.PIN2CTRL
+#define SWITCH_VECT    PORTA_PORT_vect
+#define SWITCH_INTFLG  VPORTA.INTFLAGS
+#endif
+
+
+// 7135 channel
+#ifndef PWM1_PIN
+#define PWM1_PIN PB1               //
+#define PWM1_LVL TCA0.SINGLE.CMP1BUF  // CMP1 is the output compare register for PB1
+#endif
+
+// FET channel
+#ifndef PWM2_PIN
+#define PWM2_PIN PB0               //
+#define PWM2_LVL TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
+#endif
+
+// PWM parameters of both channels are tied together because they share a counter
+#define PWM1_TOP TCA0.SINGLE.PERBUF   // holds the TOP value for for variable-resolution PWM
+// not necessary when double-buffered "BUF" registers are used
+#define PWM1_CNT TCA0.SINGLE.CNT   // for resetting phase after each TOP adjustment
+#define PWM1_PHASE_RESET_OFF  // force reset while shutting off
+#define PWM1_PHASE_RESET_ON   // force reset while turning on
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
+#endif
+
+
+// lighted button
+#ifndef AUXLED_PIN
+#define AUXLED_PIN  PIN5_bp
+#define AUXLED_PORT PORTB
+#endif
+
+
+// with so many pins, doing this all with #ifdefs gets awkward...
+// ... so just hardcode it in each hwdef file instead
+inline void hwdef_setup() {
+
+    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
+    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
+
+    //VPORTA.DIR = ...;
+    VPORTB.DIR = PIN0_bm | PIN1_bm | PIN5_bm;  // Outputs: Aux LED and PWMs
+    //VPORTC.DIR = ...;
+
+    // enable pullups on the unused pins to reduce power
+    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
+    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
+    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
+
+    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
+    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
+    PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
+    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
+    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
+
+    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
+    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
+    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
+    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
+
+    // set up the PWM
+    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
+    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
+    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
+    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
+    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
+    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
+    // See the manual for other pins, clocks, configs, portmux, etc
+    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
+    PWM1_TOP = PWM_TOP;
+    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
+}
+
+
+#endif