converted BLF GT to multi-channel

1 files changed, 102 insertions, 0 deletions

diff --git a/hwdef-blf-gt.h b/hwdef-blf-gt.h
new file mode 100644
index 0000000..fdb0cb6
--- /dev/null
+++ b/hwdef-blf-gt.h
@@ -0,0 +1,102 @@
+// BLF GT driver layout
+// Copyright (C) 2018-2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/*
+ *           ----
+ *   Reset -|1  8|- VCC (unused)
+ * eswitch -|2  7|- Voltage divider
+ * AUX LED -|3  6|- Current control (buck level)
+ *     GND -|4  5|- PWM (buck output on/off)
+ *           ----
+ *
+ * On high modes, the buck regulator's current level is adjusted by pin 6.
+ * On low modes, the buck is set to ~10% power
+ * and its output gets PWM'd by pin 5.
+ */
+
+#define ATTINY 85
+#include <avr/io.h>
+
+#define HWDEF_C_FILE hwdef-emisar-d4.c
+
+// channel modes
+// * 0. main LEDs
+#define NUM_CHANNEL_MODES   1
+enum CHANNEL_MODES {
+    CM_MAIN = 0,
+};
+
+#define DEFAULT_CHANNEL_MODE  CM_MAIN
+
+// right-most bit first, modes are in fedcba9876543210 order
+#define CHANNEL_MODES_ENABLED 0b00000001
+
+
+#define PWM_CHANNELS 2  // old, remove this
+
+#define PWM_BITS      8       // attiny85 only supports up to 8 bits
+#define PWM_GET       PWM_GET8
+#define PWM_DATATYPE  uint8_t
+#define PWM_DATATYPE2 uint16_t
+#define PWM1_DATATYPE uint8_t   // low modes (PWM with buck at 10% power)
+#define PWM2_DATATYPE uint8_t   // high modes (adjustable constant current)
+
+#define PWM_TOP_INIT  255    // highest value used in top half of ramp
+
+// low modes (PWM turns regulator on/off)
+#define CH1_PIN  PB0        // pin 5
+#define CH1_PWM  OCR0A      // OCR0A is the output compare register for PB0
+
+// high modes (control voltage sets regulator's level)
+#define CH2_PIN  PB1        // pin 6
+#define CH2_PWM  OCR0B      // OCR0B is the output compare register for PB1
+
+#define AUXLED_PIN   PB4    // pin 3
+
+// e-switch
+#define SWITCH_PIN   PB3    // pin 2
+#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
+
+// VCC is regulated, so measure battery on pin 7 instead
+#define USE_VOLTAGE_DIVIDER // use a voltage divider on pin 7, not VCC
+#define VOLTAGE_PIN PB2     // pin 7, voltage ADC
+#define VOLTAGE_CHANNEL 0x01 // MUX 01 corresponds with PB2
+#define VOLTAGE_ADC ADC1D  // Digital input disable bit corresponding with PB2
+// inherited from tk-attiny.h
+//#define VOLTAGE_ADC_DIDR DIDR0  // DIDR for ADC1
+// 1.1V reference, left-adjust, ADC1/PB2
+//#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | (1 << ADLAR) | VOLTAGE_CHANNEL)
+// 1.1V reference, no left-adjust, ADC1/PB2
+#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | VOLTAGE_CHANNEL)
+#define ADC_PRSCL   0x07    // clk/128
+
+// Raw ADC readings at 4.4V and 2.2V (in-between, we assume values form a straight line)
+#ifndef ADC_44
+#define ADC_44 (184*4)
+#endif
+#ifndef ADC_22
+#define ADC_22 (92*4)
+#endif
+
+#define FAST 0xA3           // fast PWM both channels
+#define PHASE 0xA1          // phase-correct PWM both channels
+
+
+inline void hwdef_setup() {
+    // configure PWM channels
+    DDRB = (1 << CH1_PIN)
+         | (1 << CH2_PIN);
+
+    TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
+    TCCR0A = PHASE;
+
+    // configure e-switch
+    PORTB = (1 << SWITCH_PIN);  // e-switch is the only input
+    PCMSK = (1 << SWITCH_PIN);  // pin change interrupt uses this pin
+}
+
+
+#define LAYOUT_DEFINED
+