reorganized project files (part 1)

(just moved files, didn't change the contents yet,
 and nothing will work without updating #includes and build scripts and stuff)

1 files changed, 0 insertions, 161 deletions

diff --git a/hwdef-blf-lt1-t1616.h b/hwdef-blf-lt1-t1616.h
deleted file mode 100644
index 7c1f10b..0000000
--- a/hwdef-blf-lt1-t1616.h
+++ /dev/null
@@ -1,161 +0,0 @@
-// BLF LT1 driver layout using the Attiny1616
-// Copyright (C) 2021-2023 (gchart), Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * Driver pinout:
- * eSwitch:    PA5
- * Aux LED:    PB5
- * PWM cool:   PB0 (TCA0 WO0)
- * PWM warm:   PB1 (TCA0 WO1)
- * Voltage:    VCC
- */
-
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hwdef-blf-lt1-t1616.c
-
-// allow using aux LEDs as extra channel modes
-#include "chan-aux.h"
-
-// channel modes:
-// * 0. warm only
-// * 1. cool only
-// * 2. both channels, tied together, max "200%" power
-// * 3. both channels, manual blend, max "100%" power
-// * 4. both channels, auto blend, reversible
-#define NUM_CHANNEL_MODES  6
-enum channel_modes_e {
-    CM_CH1 = 0,
-    CM_CH2,
-    CM_BOTH,
-    CM_BLEND,
-    CM_AUTO,
-    CM_AUX
-};
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b00011000
-#define USE_CHANNEL_MODE_ARGS
-// _, _, _, 128=middle CCT, 0=warm-to-cool
-#define CHANNEL_MODE_ARGS     0,0,0,128,0,0
-
-// can use some of the common handlers
-#define USE_CALC_2CH_BLEND
-
-
-#define PWM_CHANNELS  1  // old, remove this
-
-#define PWM_BITS      16     // 0 to 32640 (0 to 255 PWM + 0 to 127 DSM) at constant kHz
-#define PWM_GET       PWM_GET16
-#define PWM_DATATYPE  uint16_t
-#define PWM_DATATYPE2 uint32_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint16_t  // 15-bit PWM+DSM ramp
-
-// PWM parameters of both channels are tied together because they share a counter
-// dynamic PWM
-#define PWM_TOP  TCA0.SINGLE.PERBUF  // holds the TOP value for for variable-resolution PWM
-#define PWM_TOP_INIT  255
-#define PWM_CNT  TCA0.SINGLE.CNT  // for resetting phase after each TOP adjustment
-// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM)
-#define DSM_TOP       (255<<7) // 15-bit resolution leaves 1 bit for carry
-
-// timer interrupt for DSM
-#define DSM_vect     TCA0_OVF_vect
-#define DSM_INTCTRL  TCA0.SINGLE.INTCTRL
-#define DSM_INTFLAGS TCA0.SINGLE.INTFLAGS
-#define DSM_OVF_bm   TCA_SINGLE_OVF_bm
-
-#define DELAY_FACTOR 90  // less time in delay() because more time spent in interrupts
-
-// warm LEDs
-uint16_t ch1_dsm_lvl;
-uint8_t ch1_pwm, ch1_dsm;
-#define CH1_PIN  PB1
-#define CH1_PWM  TCA0.SINGLE.CMP1BUF  // CMP1 is the output compare register for PB1
-
-// cold LEDs
-uint16_t ch2_dsm_lvl;
-uint8_t ch2_pwm, ch2_dsm;
-#define CH2_PIN  PB0
-#define CH2_PWM  TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
-
-// lighted button
-#define AUXLED_PIN   PIN5_bp
-#define AUXLED_PORT  PORTB
-
-// e-switch
-#define SWITCH_PIN      PIN5_bp
-#define SWITCH_PORT     VPORTA.IN
-#define SWITCH_ISC_REG  PORTA.PIN2CTRL
-#define SWITCH_VECT     PORTA_PORT_vect
-#define SWITCH_INTFLG   VPORTA.INTFLAGS
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-
-inline void hwdef_setup() {
-
-    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB,
-                      CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
-
-    //VPORTA.DIR = ...;
-    // Outputs
-    VPORTB.DIR = PIN0_bm   // cool white
-               | PIN1_bm   // warm white
-    //           | PIN2_bm   // for testing on LT1S Pro, disable red channel
-               | PIN5_bm;  // aux LED
-    //VPORTC.DIR = ...;
-
-    // enable pullups on the unused pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // cold tint channel
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // warm tint channel
-    PORTB.PIN2CTRL = PORT_PULLUPEN_bm; // comment out for testing on LT1S Pro
-    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
-    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
-
-    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-
-    // set up the PWM
-    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
-    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
-    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
-    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
-    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
-    // TODO: add references to MCU documentation
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm
-                      | TCA_SINGLE_CMP1EN_bm
-                      | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc
-                      | TCA_SINGLE_ENABLE_bm;
-
-    PWM_TOP = PWM_TOP_INIT;
-
-    // set up interrupt for delta-sigma modulation
-    // (moved to hwdef.c functions so it can be enabled/disabled based on ramp level)
-    //DSM_INTCTRL |= DSM_OVF_bm;  // interrupt once for each timer cycle
-
-}
-
-
-#define LAYOUT_DEFINED
-