merged multi-channel branch with a major refactor and half a year of updates

1 files changed, 101 insertions, 0 deletions

diff --git a/hwdef-emisar-d18.h b/hwdef-emisar-d18.h
new file mode 100644
index 0000000..df08221
--- /dev/null
+++ b/hwdef-emisar-d18.h
@@ -0,0 +1,101 @@
+// Emisar D18 (FET+13+1) driver layout
+// Copyright (C) 2019-2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/*
+ *           ----
+ *   Reset -|1  8|- VCC
+ * eswitch -|2  7|- aux LED?
+ *     FET -|3  6|- 13x7135
+ *     GND -|4  5|-  1x7135
+ *           ----
+ */
+
+#define ATTINY 85
+#include <avr/io.h>
+
+#define HWDEF_C_FILE hwdef-fw3a.c
+
+// channel modes
+// * 0. FET+N+1 stacked
+#define NUM_CHANNEL_MODES   1
+enum CHANNEL_MODES {
+    CM_MAIN = 0,
+};
+
+#define DEFAULT_CHANNEL_MODE  CM_MAIN
+
+// right-most bit first, modes are in fedcba9876543210 order
+#define CHANNEL_MODES_ENABLED 0b00000001
+
+
+#define PWM_CHANNELS 3  // old, remove this
+
+#define PWM_BITS      8       // attiny85 only supports up to 8 bits
+#define PWM_GET       PWM_GET8
+#define PWM_DATATYPE  uint8_t
+#define PWM_DATATYPE2 uint16_t
+#define PWM1_DATATYPE uint8_t   // 1x7135 ramp
+#define PWM2_DATATYPE uint8_t   // 7x7135 ramp
+#define PWM3_DATATYPE uint8_t   // DD FET ramp
+
+#define PWM_TOP_INIT  255    // highest value used in top half of ramp
+
+// 1x7135 channel
+#define CH1_PIN  PB0        // pin 5, 1x7135 PWM
+#define CH1_PWM  OCR0A      // OCR0A is the output compare register for PB0
+
+// 7x7135 channel
+#define CH2_PIN  PB1        // pin 6, 7x7135 PWM
+#define CH2_PWM  OCR0B      // OCR0B is the output compare register for PB1
+
+// DD FET channel
+#define CH3_PIN  PB4        // pin 3, FET PWM
+#define CH3_PWM  OCR1B      // OCR1B is the output compare register for PB4
+
+// e-switch
+#ifndef SWITCH_PIN
+#define SWITCH_PIN   PB3    // pin 2
+#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
+#endif
+
+#ifndef AUXLED_PIN
+#define AUXLED_PIN PB2      // pin 7
+#endif
+#define ADC_PRSCL   0x07    // clk/128
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 5  // add 0.25V
+#endif
+
+#define FAST 0xA3           // fast PWM both channels
+#define PHASE 0xA1          // phase-correct PWM both channels
+
+
+inline void hwdef_setup() {
+
+    // configure PWM channels
+    DDRB = (1 << CH1_PIN)
+         | (1 << CH2_PIN)
+         | (1 << CH3_PIN);
+
+    // configure PWM channels
+    TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
+    TCCR0A = PHASE;
+
+    // Second PWM counter is ... weird
+    TCCR1 = _BV (CS10);
+    GTCCR = _BV (COM1B1) | _BV (PWM1B);
+    OCR1C = PWM_TOP_INIT;  // Set ceiling value to maximum
+
+    // configure e-switch
+    PORTB = (1 << SWITCH_PIN);  // e-switch is the only input
+    PCMSK = (1 << SWITCH_PIN);  // pin change interrupt uses this pin
+
+}
+
+
+#define LAYOUT_DEFINED
+