reorganized project files (part 1)

(just moved files, didn't change the contents yet,
 and nothing will work without updating #includes and build scripts and stuff)

1 files changed, 0 insertions, 177 deletions

diff --git a/hwdef-noctigon-k1-sbt90.h b/hwdef-noctigon-k1-sbt90.h
deleted file mode 100644
index c89c3fc..0000000
--- a/hwdef-noctigon-k1-sbt90.h
+++ /dev/null
@@ -1,177 +0,0 @@
-// Noctigon K1-SBT90.2 driver layout (attiny1634)
-// Copyright (C) 2019-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * (mostly the same as KR4 driver)
- *
- * Pin / Name / Function
- *   1    PA6   FET PWM (direct drive) (PWM1B)
- *   2    PA5   R: red aux LED (PWM0B)
- *   3    PA4   G: green aux LED
- *   4    PA3   B: blue aux LED
- *   5    PA2   (none)
- *   6    PA1   (none)
- *   7    PA0   (none)
- *   8    GND   GND
- *   9    VCC   VCC
- *  10    PC5   (none)
- *  11    PC4   (none)
- *  12    PC3   RESET
- *  13    PC2   (none)
- *  14    PC1   SCK
- *  15    PC0   (none) PWM0A
- *  16    PB3   main LED PWM (linear) (PWM1A)
- *  17    PB2   MISO / e-switch (PCINT10)
- *  18    PB1   MOSI / battery voltage (ADC6)
- *  19    PB0   Opamp power
- *  20    PA7   (none)
- *      ADC12   thermal sensor
- *
- * Main LED power uses one pin to turn the Opamp on/off,
- * and one pin to control Opamp power level.
- * Main brightness control uses the power level pin, with dynamic PWM.
- * The on/off pin is only used to turn the main LED on and off,
- * not to change brightness.
- * Also has a direct-drive FET for turbo.
- */
-
-#define ATTINY 1634
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hwdef-noctigon-kr4.c
-
-// allow using aux LEDs as extra channel modes
-#include "chan-rgbaux.h"
-
-// channel modes:
-// * 0. linear + DD FET stacked
-// * 1+. aux RGB
-#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
-enum CHANNEL_MODES {
-    CM_MAIN = 0,
-    RGB_AUX_ENUMS
-};
-
-#define DEFAULT_CHANNEL_MODE  CM_MAIN
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b0000000000000001
-// no args
-//#define USE_CHANNEL_MODE_ARGS
-//#define CHANNEL_MODE_ARGS     0,0,0,0,0,0,0,0
-
-
-#define PWM_CHANNELS 2  // old, remove this
-
-#define PWM_BITS      16        // dynamic 16-bit, but never goes over 255
-#define PWM_GET       PWM_GET8
-#define PWM_DATATYPE  uint16_t  // is used for PWM_TOPS (which goes way over 255)
-#define PWM_DATATYPE2 uint16_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint8_t   // linear ramp
-#define PWM2_DATATYPE uint8_t   // DD FET ramp
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM_TOP       ICR1   // holds the TOP value for variable-resolution PWM
-#define PWM_TOP_INIT  255    // highest value used in top half of ramp
-#define PWM_CNT       TCNT1  // for dynamic PWM, reset phase
-
-// linear channel
-#define CH1_PIN  PB3            // pin 16, Opamp reference
-#define CH1_PWM  OCR1A          // OCR1A is the output compare register for PB3
-#define CH1_ENABLE_PIN   PB0    // pin 19, Opamp power
-#define CH1_ENABLE_PORT  PORTB  // control port for PB0
-
-// DD FET channel
-#define CH2_PIN  PA6            // pin 1, DD FET PWM
-#define CH2_PWM  OCR1B          // OCR1B is the output compare register for PA6
-
-// e-switch
-#define SWITCH_PIN   PB2     // pin 17
-#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt
-#define SWITCH_PCIE  PCIE1   // PCIE1 is for PCINT[11:8]
-#define SWITCH_PCMSK PCMSK1  // PCMSK1 is for PCINT[11:8]
-#define SWITCH_PORT  PINB    // PINA or PINB or PINC
-#define SWITCH_PUE   PUEB    // pullup group B
-#define PCINT_vect   PCINT1_vect  // ISR for PCINT[11:8]
-
-#define USE_VOLTAGE_DIVIDER  // use a dedicated pin, not VCC, because VCC input is flattened
-#define VOLTAGE_PIN PB1      // Pin 18 / PB1 / ADC6
-// pin to ADC mappings are in DS table 19-4
-#define VOLTAGE_ADC      ADC6D  // digital input disable pin for PB1
-// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6
-#define VOLTAGE_ADC_DIDR DIDR1  // DIDR channel for ADC6D
-// DS tables 19-3, 19-4
-// Bit   7     6     5      4     3    2    1    0
-//     REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0
-// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1
-// divided by ...
-// REFS[1:0] = 1, 0 for internal 1.1V reference
-// other bits reserved
-#define ADMUX_VOLTAGE_DIVIDER 0b10000110
-#define ADC_PRSCL   0x07    // clk/128
-
-// TODO: calibrate this
-// Raw ADC readings at 4.4V and 2.2V
-// calibrate the voltage readout here
-// estimated / calculated values are:
-//   (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
-// D1, R1, R2 = 0, 330, 100
-#ifndef ADC_44
-//#define ADC_44 981  // raw value at 4.40V
-#define ADC_44 967  // manually tweaked so 4.16V will blink out 4.2
-#endif
-#ifndef ADC_22
-//#define ADC_22 489  // raw value at 2.20V
-#define ADC_22 482  // manually tweaked so 4.16V will blink out 4.2
-#endif
-
-#define TEMP_CHANNEL 0b00001111
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN    PA5    // pin 2
-#define AUXLED_G_PIN    PA4    // pin 3
-#define AUXLED_B_PIN    PA3    // pin 4
-#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC
-
-inline void hwdef_setup() {
-    // enable output ports
-    // Opamp level and Opamp on/off
-    DDRB = (1 << CH1_PIN)
-         | (1 << CH1_ENABLE_PIN);
-    // DD FET PWM, aux R/G/B
-    DDRA = (1 << CH2_PIN)
-         | (1 << AUXLED_R_PIN)
-         | (1 << AUXLED_G_PIN)
-         | (1 << AUXLED_B_PIN)
-         ;
-
-    // configure PWM
-    // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-    // pre-scale for timer: N = 1
-    // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
-    // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
-    // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
-    // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)
-    TCCR1A  = (1<<WGM11)  | (0<<WGM10)   // adjustable PWM (TOP=ICR1) (DS table 12-5)
-            | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-            | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
-            ;
-    TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-            | (1<<WGM13)  | (0<<WGM12)  // phase-correct adjustable PWM (DS table 12-5)
-            ;
-
-    // set PWM resolution
-    PWM_TOP = PWM_TOP_INIT;
-
-    // set up e-switch
-    SWITCH_PUE = (1 << SWITCH_PIN);  // pull-up for e-switch
-    SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
-}
-
-
-#define LAYOUT_DEFINED
-