reorganized project files (part 1)

(just moved files, didn't change the contents yet,
 and nothing will work without updating #includes and build scripts and stuff)

1 files changed, 0 insertions, 151 deletions

diff --git a/hwdef-sofirn-lt1s-pro.h b/hwdef-sofirn-lt1s-pro.h
deleted file mode 100644
index ae6b3bf..0000000
--- a/hwdef-sofirn-lt1s-pro.h
+++ /dev/null
@@ -1,151 +0,0 @@
-// BLF LT1S Pro driver layout using the Attiny1616
-// Copyright (C) 2022-2023 (FIXME)
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * Driver pinout:
- * eSwitch:    PA5
- * Aux LED:    PB5
- * WW PWM:     PB0 (TCA0 WO0)
- * CW PWM:     PB1 (TCA0 WO1)
- * Red PWM:    PB2 (TCA0 WO2)
- * Voltage:    VCC
- */
-
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hwdef-sofirn-lt1s-pro.c
-
-// channel modes:
-// * 0. warm/cool white blend
-// * 1. auto 2ch white blend (warm -> cool by ramp level)
-// * 2. auto 3ch blend (red -> warm -> cool by ramp level)
-// * 3. red only
-// * 4. red + white blend
-#define NUM_CHANNEL_MODES 5
-enum channel_modes_e {
-    CM_WHITE = 0,
-    CM_AUTO2,
-    CM_AUTO3,
-    CM_RED,
-    CM_WHITE_RED,
-};
-
-#define CHANNEL_MODES_ENABLED 0b00011111
-#define USE_CHANNEL_MODE_ARGS
-// 128=middle CCT, _, _, _, 255=100% red
-#define CHANNEL_MODE_ARGS     128,0,0,0,255
-
-// can use some of the common handlers
-#define USE_CALC_2CH_BLEND
-//#define USE_CALC_AUTO_3CH_BLEND
-
-
-#define PWM_CHANNELS   1  // old, remove this
-
-// only using 16-bit PWM on this light
-#define PWM_BITS      16
-
-#define PWM_GET       PWM_GET16
-#define PWM_DATATYPE  uint16_t
-#define PWM1_DATATYPE uint16_t
-#define PWM_DATATYPE2 uint32_t
-
-// dynamic PWM
-// PWM parameters of all channels are tied together because they share a counter
-#define PWM_TOP_INIT  511  // highest value used in the top half of the ramp
-#define PWM_TOP TCA0.SINGLE.PERBUF   // holds the TOP value for for variable-resolution PWM
-#define PWM_CNT TCA0.SINGLE.CNT   // for resetting phase after each TOP adjustment
-
-// warm LEDs
-//#define WARM_PWM_PIN PB0
-#define WARM_PWM_LVL TCA0.SINGLE.CMP0BUF  // CMP1 is the output compare register for PB0
-
-// cold LEDs
-//#define COOL_PWM_PIN PB1
-#define COOL_PWM_LVL TCA0.SINGLE.CMP1BUF  // CMP0 is the output compare register for PB1
-
-// red LEDs
-//#define RED_PWM_PIN PB2
-#define RED_PWM_LVL TCA0.SINGLE.CMP2BUF   // CMP2 is the output compare register for PB2
-
-// lighted button
-#define AUXLED_PIN   PIN5_bp
-#define AUXLED_PORT  PORTB
-
-// the button lights up
-#define USE_INDICATOR_LED
-// the button is visible while main LEDs are on
-#define USE_INDICATOR_LED_WHILE_RAMPING
-
-// e-switch
-#define SWITCH_PIN     PIN5_bp
-#define SWITCH_PORT    VPORTA.IN
-#define SWITCH_ISC_REG PORTA.PIN2CTRL
-#define SWITCH_VECT    PORTA_PORT_vect
-#define SWITCH_INTFLG  VPORTA.INTFLAGS
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-
-inline void hwdef_setup() {
-
-    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB,
-                      CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
-
-    //VPORTA.DIR = ...;
-    // Outputs
-    VPORTB.DIR = PIN0_bm   // warm white
-               | PIN1_bm   // cool white
-               | PIN2_bm   // red
-               | PIN5_bm;  // aux LED
-    //VPORTC.DIR = ...;
-
-    // enable pullups on the unused pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // warm tint channel
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // cold tint channel
-    //PORTB.PIN2CTRL = PORT_PULLUPEN_bm; // red LEDs
-    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
-    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
-
-    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-
-    // set up the PWM
-    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
-    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
-    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
-    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
-    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
-    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
-    // TODO: add references to MCU documentation
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm
-                      | TCA_SINGLE_CMP1EN_bm
-                      | TCA_SINGLE_CMP2EN_bm
-                      | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
-    PWM_TOP = PWM_TOP_INIT;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc
-                      | TCA_SINGLE_ENABLE_bm;
-}
-
-
-#define LAYOUT_DEFINED
-