reorganized project files (part 1)

(just moved files, didn't change the contents yet,
 and nothing will work without updating #includes and build scripts and stuff)

1 files changed, 0 insertions, 181 deletions

diff --git a/hwdef-thefreeman-boost21-mp3431-hdr-dac-argb.h b/hwdef-thefreeman-boost21-mp3431-hdr-dac-argb.h
deleted file mode 100644
index 1c35014..0000000
--- a/hwdef-thefreeman-boost21-mp3431-hdr-dac-argb.h
+++ /dev/null
@@ -1,181 +0,0 @@
-// hwdef for thefreeman's boost driver 2.1 w/ MP3431, DAC, ARGB
-// Copyright (C) 2023 TBD (thefreeman), Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/* thefreeman’s Boost driver based on MP3431 and attiny1616
- * with high dynamic range and DAC control, AUX : RGB + button
- * hardware version : 2.0+
- * compatible with BST20-FWxA v1.0 (no button LED A)
- *
- * Pin / Name / Function
- *   1    PA2   
- *   2    PA3   
- *   3    GND   GND
- *   4    VCC   VCC
- *   5    PA4   
- *   6    PA5   
- *   7    PA6   DAC
- *   8    PA7   
- *   9    PB5   IN- NFET
- *  10    PB4   HDR
- *  11    PB3   B: blue aux LED
- *  12    PB2   G: green aux LED
- *  13    PB1   R: red aux LED
- *  14    PB0   
- *  15    PC0   boost enable
- *  16    PC1   A: button LED
- *  17    PC2   e-switch
- *  18    PC3   
- *  19    PA0   UDPI
- *  20    PA1   
- *
- * BST EN enable the boost regulator and Op-Amp
- * DAC sets the current, max current depends on Vset voltage divider and Rsense
- * HDR FET switches between high value Rsense (low current range, pin low),
- *         and low value Rsense (high current range, pin high)
- * IN- NFET : pull up after BST enable to eliminate startup flash, pull down otherwise
- */
-
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define HWDEF_C_FILE hwdef-thefreeman-boost21-mp3431-hdr-dac-argb.c
-
-// allow using aux LEDs as extra channel modes
-#include "chan-rgbaux.h"
-
-// channel modes:
-// * 0. main LEDs
-// * 1+. aux RGB
-#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
-enum CHANNEL_MODES {
-    CM_MAIN = 0,
-    RGB_AUX_ENUMS
-};
-
-#define DEFAULT_CHANNEL_MODE  CM_MAIN
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b0000000000000001
-
-
-#define PWM_CHANNELS  1  // old, remove this
-
-#define PWM_BITS      8         // 8-bit DAC
-#define PWM_GET       PWM_GET8
-#define PWM_DATATYPE  uint8_t
-#define PWM_DATATYPE2 uint16_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint8_t   // main LED ramp
-
-// main LED outputs
-#define DAC_LVL   DAC0.DATA    // 0 to 255, for 0V to Vref
-#define DAC_VREF  VREF.CTRLA   // 0.55V or 2.5V
-#define PWM_TOP_INIT  255      // highest value used in top half of ramp (unused?)
-// Vref values
-#define V055  16
-#define V11   17
-#define V25   18
-#define V43   19
-#define V15   20
-
-// BST enable
-#define BST_ENABLE_PIN   PIN0_bp
-#define BST_ENABLE_PORT  PORTC_OUT
-
-// HDR
-// turns on HDR FET for the high current range
-#define HDR_ENABLE_PIN   PIN4_bp
-#define HDR_ENABLE_PORT  PORTB_OUT
-
-// IN- NFET
-// pull high to force output to zero to eliminate the startup flash
-#define IN_NFET_DELAY_TIME   8  // (ms)
-#define IN_NFET_ENABLE_PIN   PIN5_bp
-#define IN_NFET_ENABLE_PORT  PORTB_OUT
-
-// e-switch
-#ifndef SWITCH_PIN
-#define SWITCH_PIN      PIN2_bp
-#define SWITCH_PORT     VPORTC.IN
-#define SWITCH_ISC_REG  PORTC.PIN2CTRL
-#define SWITCH_VECT     PORTC_PORT_vect
-#define SWITCH_INTFLG   VPORTC.INTFLAGS
-#define SWITCH_PCINT    PCINT0
-#define PCINT_vect      PCINT0_vect
-#endif
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 0  // using a PFET so no appreciable drop
-#endif
-
-// this driver allows for aux LEDs under the optic
-#define AUXLED_R_PIN  PIN1_bp
-#define AUXLED_G_PIN  PIN2_bp
-#define AUXLED_B_PIN  PIN3_bp
-#define AUXLED_RGB_PORT PORTB  // PORTA or PORTB or PORTC
-
-// this light has three aux LED channels: R, G, B
-#define USE_AUX_RGB_LEDS
-
-// A: button LED
-#ifndef BUTTON_LED_PIN
-#define BUTTON_LED_PIN  PIN1_bp
-#define BUTTON_LED_PORT PORTC
-#endif
-
-
-inline void hwdef_setup() {
-
-    // TODO: for this DAC controlled-light, try to decrease the clock speed or use the ULP
-    // set up the system clock to run at 10 MHz to match other attiny1616 lights
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB,
-                      CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
-
-    VPORTA.DIR = PIN6_bm;  // DAC
-    VPORTB.DIR = PIN1_bm   // R
-               | PIN2_bm   // G
-               | PIN3_bm   // B
-               | PIN4_bm   // HDR
-               | PIN5_bm;  // IN- NFET
-    VPORTC.DIR = PIN0_bm   // BST EN
-               | PIN1_bm;  // A
-
-    // enable pullups on the input pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
-    //PORTA.PIN6CTRL = PORT_PULLUPEN_bm;  // DAC
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    PORTB.PIN0CTRL = PORT_PULLUPEN_bm;
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm;  // R
-    //PORTB.PIN2CTRL = PORT_PULLUPEN_bm;  // G
-    //PORTB.PIN3CTRL = PORT_PULLUPEN_bm;  // B
-    //PORTB.PIN4CTRL = PORT_PULLUPEN_bm;  // HDR
-    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm;  // IN- NFET
-
-    //PORTC.PIN0CTRL = PORT_PULLUPEN_bm;  // EN
-    //PORTC.PIN1CTRL = PORT_PULLUPEN_bm;  // A
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm
-                   | PORT_ISC_BOTHEDGES_gc;  // e-switch
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-
-    // set up the DAC
-    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
-    // DAC ranges from 0V to (255 * Vref) / 256
-    // also VREF_DAC0REFSEL_0V55_gc and VREF_DAC0REFSEL_1V1_gc and VREF_DAC0REFSEL_2V5_gc
-    VREF.CTRLA |= VREF_DAC0REFSEL_2V5_gc;
-    VREF.CTRLB |= VREF_DAC0REFEN_bm;
-    DAC0.CTRLA = DAC_ENABLE_bm | DAC_OUTEN_bm;
-    DAC0.DATA = 255; // set the output voltage
-
-}
-
-
-#define LAYOUT_DEFINED
-