aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--hwdef-Emisar_D4Sv2.h123
-rw-r--r--hwdef-emisar-d4sv2.c54
-rw-r--r--hwdef-emisar-d4sv2.h196
-rw-r--r--hwdef-emisar-d4v2.h4
-rw-r--r--spaghetti-monster/anduril/cfg-emisar-d4sv2.h74
5 files changed, 300 insertions, 151 deletions
diff --git a/hwdef-Emisar_D4Sv2.h b/hwdef-Emisar_D4Sv2.h
deleted file mode 100644
index bd63649..0000000
--- a/hwdef-Emisar_D4Sv2.h
+++ /dev/null
@@ -1,123 +0,0 @@
-// Emisar D4Sv2 driver layout (attiny1634)
-// Copyright (C) 2019-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * (same layout as D4v2, except it's a FET+3+1 instead of FET+1)
- *
- * Pin / Name / Function
- * 1 PA6 FET PWM (PWM1B)
- * 2 PA5 red aux LED (PWM0B)
- * 3 PA4 green aux LED
- * 4 PA3 blue aux LED
- * 5 PA2 e-switch
- * 6 PA1 (none)
- * 7 PA0 (none)
- * 8 GND GND
- * 9 VCC VCC
- * 10 PC5 (none)
- * 11 PC4 (none)
- * 12 PC3 RESET
- * 13 PC2 (none)
- * 14 PC1 SCK
- * 15 PC0 3x7135 PWM (PWM0A)
- * 16 PB3 1x7135 PWM (PWM1A)
- * 17 PB2 MISO
- * 18 PB1 MOSI
- * 19 PB0 (none)
- * 20 PA7 (none)
- * ADC12 thermal sensor
- */
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1634
-#include <avr/io.h>
-
-#define SWITCH_PIN PA2 // pin 5
-#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt
-#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0]
-#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
-#define SWITCH_PORT PINA // PINA or PINB or PINC
-
-#define PWM_CHANNELS 3
-
-#define PWM1_PIN PB3 // pin 16, 1x7135 PWM
-#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3
-
-#define PWM2_PIN PC0 // pin 15, 3x7135 PWM
-#define PWM2_LVL OCR0A // OCR0A is the output compare register for PC0
-
-#define PWM3_PIN PA6 // pin 1, FET PWM
-#define PWM3_LVL OCR1B // OCR1B is the output compare register for PB1
-
-
-#define ADC_PRSCL 0x07 // clk/128
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V)
-#endif
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN PA5 // pin 2
-#define AUXLED_G_PIN PA4 // pin 3
-#define AUXLED_B_PIN PA3 // pin 4
-#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
- // enable output ports
- // FET, aux R/G/B
- DDRA = (1 << PWM3_PIN)
- | (1 << AUXLED_R_PIN)
- | (1 << AUXLED_G_PIN)
- | (1 << AUXLED_B_PIN)
- ;
- // 1x7135
- DDRB = (1 << PWM1_PIN);
- // 3x7135
- DDRC = (1 << PWM2_PIN);
-
- // configure PWM
- // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
- // pre-scale for timer: N = 1
- // WGM1[3:0]: 0,0,0,1: PWM, Phase Correct, 8-bit (DS table 12-5)
- // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6)
- // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4)
- // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4)
- TCCR1A = (0<<WGM11) | (1<<WGM10) // 8-bit (TOP=0xFF) (DS table 12-5)
- | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4)
- | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4)
- ;
- TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6)
- | (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5)
- ;
-
- // WGM0[2:0]: 0,0,1: PWM, Phase Correct (DS table 11-8)
- // CS0[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 11-9)
- // COM0A[1:0]: 1,0: PWM OC0A in the normal direction (DS table 11-4)
- // COM0B[1:0]: 0,0: OC0B disabled (DS table 11-7)
- // TCCR0A: COM0A1, COM0A0, COM0B1, COM0B0, -, -, WGM01, WGM00
- TCCR0A = (0<<WGM01) | (1<<WGM00) // PWM, Phase Correct, TOP=0xFF (DS table 11-5)
- | (1<<COM1A1) | (0<<COM1A0) // PWM 0A in normal direction (DS table 11-4)
- | (0<<COM1B1) | (0<<COM1B0) // PWM 0B disabled (DS table 11-7)
- ;
- // TCCR0B: FOC0A, FOC0B, -, -, WGM02, CS02, CS01, CS00
- TCCR0B = (0<<CS02) | (0<<CS01) | (1<<CS00) // clk/1 (no prescaling) (DS table 11-9)
- | (0<<WGM02) // PWM, Phase Correct, TOP=0xFF (DS table 11-8)
- ;
-
- // set up e-switch
- //PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC?
- PUEA = (1 << SWITCH_PIN); // pull-up for e-switch
- SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt
-}
-
-#define LAYOUT_DEFINED
-
diff --git a/hwdef-emisar-d4sv2.c b/hwdef-emisar-d4sv2.c
new file mode 100644
index 0000000..d67efb5
--- /dev/null
+++ b/hwdef-emisar-d4sv2.c
@@ -0,0 +1,54 @@
+// Emisar D4Sv2 PWM helper functions
+// Copyright (C) 2019-2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+
+#pragma once
+
+#include "chan-rgbaux.c"
+
+// single set of LEDs with 3 stacked power channels, DDFET+3+1
+void set_level_main(uint8_t level) {
+ if (level == 0) {
+ CH1_PWM = 0;
+ CH2_PWM = 0;
+ CH3_PWM = 0;
+ PWM_CNT = 0; // reset phase
+ return;
+ }
+
+ level --; // PWM array index = level - 1
+ PWM_DATATYPE ch1_pwm = PWM_GET(pwm1_levels, level);
+ PWM_DATATYPE ch2_pwm = PWM_GET(pwm2_levels, level);
+ PWM_DATATYPE ch3_pwm = PWM_GET(pwm3_levels, level);
+ // pulse frequency modulation, a.k.a. dynamic PWM
+ uint16_t top = PWM_GET16(pwm_tops, level);
+
+ CH1_PWM = ch1_pwm;
+ CH2_PWM = ch2_pwm;
+ CH3_PWM = ch3_pwm;
+ // wait to sync the counter and avoid flashes
+ while(actual_level && (PWM_CNT > (top - 32))) {}
+ PWM_TOP = top;
+ // force reset phase when turning on from zero
+ // (because otherwise the initial response is inconsistent)
+ if (! actual_level) PWM_CNT = 0;
+}
+
+bool gradual_tick_main(uint8_t gt) {
+ PWM_DATATYPE pwm1 = PWM_GET(pwm1_levels, gt);
+ PWM_DATATYPE pwm2 = PWM_GET(pwm2_levels, gt);
+ PWM_DATATYPE pwm3 = PWM_GET(pwm3_levels, gt);
+
+ GRADUAL_ADJUST_STACKED(pwm1, CH1_PWM, PWM_TOP_INIT);
+ GRADUAL_ADJUST_STACKED(pwm2, CH2_PWM, PWM_TOP_INIT);
+ GRADUAL_ADJUST_SIMPLE (pwm3, CH3_PWM);
+
+ if ( (pwm1 == CH1_PWM)
+ && (pwm2 == CH2_PWM)
+ && (pwm3 == CH3_PWM)
+ ) {
+ return true; // done
+ }
+ return false; // not done yet
+}
+
diff --git a/hwdef-emisar-d4sv2.h b/hwdef-emisar-d4sv2.h
new file mode 100644
index 0000000..0607c24
--- /dev/null
+++ b/hwdef-emisar-d4sv2.h
@@ -0,0 +1,196 @@
+// Emisar D4Sv2 driver layout (attiny1634)
+// Copyright (C) 2019-2023 Selene ToyKeeper
+// SPDX-License-Identifier: GPL-3.0-or-later
+#pragma once
+
+/*
+ * (same layout as D4v2, except it's a FET+3+1 instead of FET+1)
+ *
+ * Pin / Name / Function
+ * 1 PA6 FET PWM (PWM1B)
+ * 2 PA5 red aux LED (PWM0B)
+ * 3 PA4 green aux LED
+ * 4 PA3 blue aux LED
+ * 5 PA2 e-switch
+ * 6 PA1 button LED?
+ * 7 PA0 (none)
+ * 8 GND GND
+ * 9 VCC VCC
+ * 10 PC5 (none)
+ * 11 PC4 (none)
+ * 12 PC3 RESET
+ * 13 PC2 (none)
+ * 14 PC1 SCK
+ * 15 PC0 3x7135 PWM (PWM0A) (8-bit)
+ * 16 PB3 1x7135 PWM (PWM1A)
+ * 17 PB2 MISO
+ * 18 PB1 MOSI
+ * 19 PB0 (none)
+ * 20 PA7 (none)
+ * ADC12 thermal sensor
+ */
+
+#define ATTINY 1634
+#include <avr/io.h>
+
+#define HWDEF_C_FILE hwdef-emisar-d4sv2.c
+
+// allow using aux LEDs as extra channel modes
+#include "chan-rgbaux.h"
+
+#define USE_CHANNEL_MODES
+// channel modes:
+// * 0. FET+3+1 stacked
+// * 1. aux red
+// * 2. aux green
+// * 3. aux blue
+#define NUM_CHANNEL_MODES 4
+#define CM_MAIN 0
+#define CM_AUXRED 1
+#define CM_AUXGRN 2
+#define CM_AUXBLU 3
+
+#define DEFAULT_CHANNEL_MODE CM_MAIN
+
+#define CHANNEL_MODES_ENABLED 0b00000001
+#define CHANNEL_HAS_ARGS 0b00000000
+// no args
+//#define USE_CHANNEL_MODE_ARGS
+//#define CHANNEL_MODE_ARGS 0,0,0,0
+
+#define SET_LEVEL_MODES set_level_main, \
+ set_level_auxred, \
+ set_level_auxgrn, \
+ set_level_auxblu
+// gradual ticking for thermal regulation
+#define GRADUAL_TICK_MODES gradual_tick_main, \
+ gradual_tick_null, \
+ gradual_tick_null, \
+ gradual_tick_null
+
+
+#define PWM_CHANNELS 3 // old, remove this
+
+#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255
+#define PWM_GET PWM_GET8
+#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255)
+#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255
+#define PWM1_DATATYPE uint8_t // 1x7135 ramp (16-bit)
+#define PWM2_DATATYPE uint8_t // 3x7135 ramp (8-bit)
+#define PWM3_DATATYPE uint8_t // DD FET ramp (16-bit)
+
+// PWM parameters of FET and 1x7135 channels are tied together because they share a counter
+#define PWM_TOP ICR1 // holds the TOP value for for variable-resolution PWM
+#define PWM_TOP_INIT 255 // highest value used in top half of ramp
+#define PWM_CNT TCNT1 // for dynamic PWM, reset phase
+
+// 1x7135 channel
+#define CH1_PIN PB3 // pin 16, 1x7135 PWM
+#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3
+
+// 3x7135 channel
+#define CH2_PIN PC0 // pin 15, 3x7135 PWM
+#define CH2_PWM OCR0A // OCR0A is the output compare register for PC0
+
+// DD FET channel
+#define CH3_PIN PA6 // pin 1, DD FET PWM
+#define CH3_PWM OCR1B // OCR1B is the output compare register for PB1
+
+// e-switch
+#define SWITCH_PIN PA2 // pin 5
+#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt
+#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0]
+#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
+#define SWITCH_PORT PINA // PINA or PINB or PINC
+#define SWITCH_PUE PUEA // pullup group A
+#define PCINT_vect PCINT0_vect // ISR for PCINT[7:0]
+
+
+#define ADC_PRSCL 0x07 // clk/128
+
+// average drop across diode on this hardware
+#ifndef VOLTAGE_FUDGE_FACTOR
+#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V)
+#endif
+
+// this light has aux LEDs under the optic
+#define AUXLED_R_PIN PA5 // pin 2
+#define AUXLED_G_PIN PA4 // pin 3
+#define AUXLED_B_PIN PA3 // pin 4
+#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
+#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC
+#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC
+
+#define BUTTON_LED_PIN PA1 // pin 6
+#define BUTTON_LED_PORT PORTA // for all "PA" pins
+#define BUTTON_LED_DDR DDRA // for all "PA" pins
+#define BUTTON_LED_PUE PUEA // for all "PA" pins
+
+// this light has three aux LED channels: R, G, B
+#define USE_AUX_RGB_LEDS
+// it also has an independent LED in the button
+#define USE_BUTTON_LED
+// the aux LEDs are front-facing, so turn them off while main LEDs are on
+#ifdef USE_INDICATOR_LED_WHILE_RAMPING
+#undef USE_INDICATOR_LED_WHILE_RAMPING
+#endif
+
+void set_level_main(uint8_t level);
+
+bool gradual_tick_main(uint8_t gt);
+
+
+inline void hwdef_setup() {
+ // enable output ports
+ // 3x7135
+ DDRC = (1 << CH2_PIN);
+ // 1x7135
+ DDRB = (1 << CH1_PIN);
+ // FET, aux R/G/B
+ DDRA = (1 << CH3_PIN)
+ | (1 << AUXLED_R_PIN)
+ | (1 << AUXLED_G_PIN)
+ | (1 << AUXLED_B_PIN)
+ | (1 << BUTTON_LED_PIN)
+ ;
+
+ // configure PWM
+ // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
+ // pre-scale for timer: N = 1
+ // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
+ // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6)
+ // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4)
+ // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4)
+ TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5)
+ | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4)
+ | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4)
+ ;
+ TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6)
+ | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5)
+ ;
+
+ // WGM0[2:0]: 0,0,1: PWM, Phase Correct (DS table 11-8)
+ // CS0[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 11-9)
+ // COM0A[1:0]: 1,0: PWM OC0A in the normal direction (DS table 11-4)
+ // COM0B[1:0]: 0,0: OC0B disabled (DS table 11-7)
+ // TCCR0A: COM0A1, COM0A0, COM0B1, COM0B0, -, -, WGM01, WGM00
+ TCCR0A = (0<<WGM01) | (1<<WGM00) // PWM, Phase Correct, TOP=0xFF (DS table 11-5)
+ | (1<<COM1A1) | (0<<COM1A0) // PWM 0A in normal direction (DS table 11-4)
+ | (0<<COM1B1) | (0<<COM1B0) // PWM 0B disabled (DS table 11-7)
+ ;
+ // TCCR0B: FOC0A, FOC0B, -, -, WGM02, CS02, CS01, CS00
+ TCCR0B = (0<<CS02) | (0<<CS01) | (1<<CS00) // clk/1 (no prescaling) (DS table 11-9)
+ | (0<<WGM02) // PWM, Phase Correct, TOP=0xFF (DS table 11-8)
+ ;
+
+ // set PWM resolution
+ PWM_TOP = PWM_TOP_INIT;
+
+ // set up e-switch
+ SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch
+ SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt
+}
+
+
+#define LAYOUT_DEFINED
+
diff --git a/hwdef-emisar-d4v2.h b/hwdef-emisar-d4v2.h
index e9ffe11..813dbf3 100644
--- a/hwdef-emisar-d4v2.h
+++ b/hwdef-emisar-d4v2.h
@@ -1,5 +1,5 @@
// hwdef for Emisar D4v2 (attiny1634)
-// Copyright (C) 2018 Selene ToyKeeper
+// Copyright (C) 2018-2023 Selene ToyKeeper
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
@@ -73,7 +73,7 @@
#define PWM_GET PWM_GET8
#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255)
#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint8_t // linear ramp
+#define PWM1_DATATYPE uint8_t // 1x7135 ramp
#define PWM2_DATATYPE uint8_t // DD FET ramp
// PWM parameters of both channels are tied together because they share a counter
diff --git a/spaghetti-monster/anduril/cfg-emisar-d4sv2.h b/spaghetti-monster/anduril/cfg-emisar-d4sv2.h
index 1bf2c2e..10883b8 100644
--- a/spaghetti-monster/anduril/cfg-emisar-d4sv2.h
+++ b/spaghetti-monster/anduril/cfg-emisar-d4sv2.h
@@ -4,52 +4,74 @@
#pragma once
#define MODEL_NUMBER "0133"
-#include "hwdef-Emisar_D4Sv2.h"
+#include "hwdef-emisar-d4sv2.h"
#include "hank-cfg.h"
// ATTINY: 1634
-// this light has three aux LED channels: R, G, B
-#define USE_AUX_RGB_LEDS
-// the aux LEDs are front-facing, so turn them off while main LEDs are on
-#ifdef USE_INDICATOR_LED_WHILE_RAMPING
-#undef USE_INDICATOR_LED_WHILE_RAMPING
-#endif
-
+#define RAMP_SIZE 150
// 1x7135 + 3x7135 + FET
-// ../../../bin/level_calc.py seventh 3 150 7135 1 2.3 130 7135 11 5 400.1 FET 2 10 4000
-// (and some manual edits to make the clock speed changes smoother)
-#define PWM1_LEVELS 1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,17,18,19,20,21,22,24,26,28,30,33,35,38,41,44,47,50,54,57,61,65,69,74,79,84,89,94,100,106,113,119,126,134,142,150,158,167,176,186,196,207,218,230,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
-#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,12,16,21,25,30,35,41,46,52,58,64,71,77,84,92,99,107,115,124,133,142,151,161,172,182,193,205,217,229,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
-#define PWM3_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,3,5,6,8,10,12,14,16,18,20,23,25,27,30,32,35,38,41,44,47,50,53,57,60,64,67,71,75,79,83,87,92,96,101,106,111,116,121,127,132,138,144,150,156,163,169,176,183,190,197,205,213,221,229,237,246,255
-#define MAX_1x7135 62
-#define MAX_Nx7135 93
-#define HALFSPEED_LEVEL 18
-#define QUARTERSPEED_LEVEL 8
-
-//#define DEFAULT_LEVEL MAX_Nx7135
+
+// level_calc.py 5.7895 3 150 7135 1 0.1 130 7135 1 1 321.43 FET 2 10 3000 --pwm dyn:74:4096:255:3
+#define PWM1_LEVELS 1,1,2,3,3,4,5,6,7,8,9,11,12,13,15,16,18,19,21,23,26,27,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,71,74,76,78,80,82,85,87,90,93,96,100,103,107,112,116,122,127,133,140,147,154,163,171,182,192,203,215,228,241,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,6,12,19,25,32,40,47,55,64,72,81,91,101,111,122,133,144,156,169,182,195,209,224,239,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+#define PWM3_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,3,5,7,10,12,15,17,20,22,25,28,31,34,38,41,44,48,52,56,60,64,68,72,77,81,86,91,96,101,107,112,118,124,130,136,143,149,156,163,170,178,186,193,201,210,218,227,236,245,255
+#define PWM_TOPS 4095,2701,3200,3586,2518,2778,2834,2795,2705,2587,2455,2582,2412,2247,2256,2091,2062,1907,1860,1802,1737,1605,1542,1477,1412,1347,1284,1222,1162,1105,1050,997,946,898,853,810,768,730,693,658,625,594,564,536,503,485,462,439,418,398,384,366,353,340,327,319,307,298,292,284,280,273,269,266,263,260,258,256,256,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+#define MIN_THERM_STEPDOWN 70 // should be above highest dyn_pwm level
+#define MAX_1x7135 75
+#define MAX_Nx7135 100
+#define HALFSPEED_LEVEL 20
+#define QUARTERSPEED_LEVEL 5
+
+// old
+//// ../../../bin/level_calc.py seventh 3 150 7135 1 2.3 130 7135 11 5 400.1 FET 2 10 4000
+//// (and some manual edits to make the clock speed changes smoother)
+//#define PWM1_LEVELS 1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,17,18,19,20,21,22,24,26,28,30,33,35,38,41,44,47,50,54,57,61,65,69,74,79,84,89,94,100,106,113,119,126,134,142,150,158,167,176,186,196,207,218,230,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+//#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,12,16,21,25,30,35,41,46,52,58,64,71,77,84,92,99,107,115,124,133,142,151,161,172,182,193,205,217,229,242,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0
+//#define PWM3_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,3,5,6,8,10,12,14,16,18,20,23,25,27,30,32,35,38,41,44,47,50,53,57,60,64,67,71,75,79,83,87,92,96,101,106,111,116,121,127,132,138,144,150,156,163,169,176,183,190,197,205,213,221,229,237,246,255
+//#define PWM_TOPS 255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+//#define MAX_1x7135 62
+//#define MAX_Nx7135 93
+//#define HALFSPEED_LEVEL 18
+//#define QUARTERSPEED_LEVEL 8
+
+
+#define DEFAULT_LEVEL MAX_Nx7135
#define RAMP_SMOOTH_FLOOR 1
#define RAMP_SMOOTH_CEIL 130
-// 20, 38, 56, 75, [93], 111, 130
+// 20, 38, 56, [75], 93, 111, 130
#define RAMP_DISCRETE_FLOOR 20
#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
#define RAMP_DISCRETE_STEPS 7
// safe limit ~35% power, 150% of sustainable thermal power
-// 20 44 69 [93] 118
-#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR
-#define SIMPLE_UI_CEIL 118
+// 25 50 [75] [100] 125
+#define SIMPLE_UI_FLOOR 25
+#define SIMPLE_UI_CEIL 125
#define SIMPLE_UI_STEPS 5
-#define STROBE_BRIGHTNESS MAX_LEVEL
+#define STROBE_BRIGHTNESS MAX_LEVEL
// stop panicking at ~50% power or ~2000 lm
#define THERM_FASTER_LEVEL 130
+#define THERM_CAL_OFFSET 5
+
+// show each channel while it scroll by in the menu
+#define USE_CONFIG_COLORS
+
+// use aux red + aux blue for police strobe
+#define USE_POLICE_COLOR_STROBE_MODE
+#define POLICE_STROBE_USES_AUX
+#define POLICE_COLOR_STROBE_CH1 CM_AUXRED
+#define POLICE_COLOR_STROBE_CH2 CM_AUXBLU
+
+// the default of 26 looks a bit rough, so increase it to make it smoother
+#define CANDLE_AMPLITUDE 33
+
+// don't blink while ramping
#ifdef BLINK_AT_RAMP_MIDDLE
#undef BLINK_AT_RAMP_MIDDLE
#endif
-// seems relevant on attiny1634
-#define THERM_CAL_OFFSET 5
generated by cgit v1.2.3 (git 2.25.1) at 2026-03-28 17:07:31 +0000