diff options
| -rw-r--r-- | hwdef-Noctigon_DM11-12V.h | 166 | ||||
| -rw-r--r-- | hwdef-noctigon-dm11-boost.c | 47 | ||||
| -rw-r--r-- | hwdef-noctigon-dm11-boost.h | 226 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/MODELS | 3 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/cfg-noctigon-dm11-boost.h (renamed from spaghetti-monster/anduril/cfg-noctigon-dm11-12v.h) | 50 |
5 files changed, 301 insertions, 191 deletions
diff --git a/hwdef-Noctigon_DM11-12V.h b/hwdef-Noctigon_DM11-12V.h deleted file mode 100644 index 104b6ae..0000000 --- a/hwdef-Noctigon_DM11-12V.h +++ /dev/null @@ -1,166 +0,0 @@ -// Noctigon DM11 (12V) driver layout (attiny1634) -// Copyright (C) 2021-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * (based on Noctigon K1) - * - * Pin / Name / Function - * 1 PA6 (none) (PWM1B) (reserved for DD drivers) - * 2 PA5 R: red aux LED (PWM0B) - * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED - * 5 PA2 L: button LED - * 6 PA1 (none) - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 boost PMIC enable (PWM0A not used) - * 16 PB3 main LED PWM (PWM1A) - * 17 PB2 MISO / e-switch? (PCINT10) - * 18 PB1 MOSI / battery voltage (ADC6) - * 19 PB0 Opamp power - * 20 PA7 e-switch? (PCINT7) - * ADC12 thermal sensor - * - * Main LED power uses one pin to turn the Opamp on/off, - * and one pin to control Opamp power level. - * Linear brightness control uses the power level pin, with dynamic PWM. - * The on/off pin is only used to turn the main LED on and off, - * not to change brightness. - */ - -#ifdef ATTINY -#undef ATTINY -#endif -#define ATTINY 1634 -#include <avr/io.h> - -#define PWM_CHANNELS 1 // can't use DD FET on boost drivers -#define PWM_BITS 16 // data type needs 16 bits, not 8 -#define PWM_TOP 255 // highest value used in top half of ramp -#define USE_DYN_PWM // dynamic frequency and speed - -//#define SWITCH_PIN PB2 // pin 17 -//#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt -//#define SWITCH_PCIE PCIE1 // PCIE1 is for PCINT[11:8] -//#define SWITCH_PCMSK PCMSK1 // PCMSK1 is for PCINT[11:8] -//#define SWITCH_PORT PINB // PINA or PINB or PINC -//#define PCINT_vect PCINT1_vect // ISR for PCINT[11:8] - -#define SWITCH_PIN PA7 // pin 20 -#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC - -#define PWM1_PIN PB3 // pin 16, Opamp reference -#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 -#define PWM1_CNT TCNT1 // for dynamic PWM, reset phase -#define PWM1_PHASE_RESET_OFF // force reset while shutting off -#define PWM1_PHASE_RESET_ON // force reset while turning on -#define PWM1_PHASE_SYNC // manual sync while changing level - -// PWM parameters of both channels are tied together because they share a counter -#define PWM1_TOP ICR1 // holds the TOP value for for variable-resolution PWM - -#define LED_ENABLE_PIN PB0 // pin 19, Opamp power -#define LED_ENABLE_PORT PORTB // control port for PB0 - -#define LED2_ENABLE_PIN PC0 // pin 15, boost PMIC enable -#define LED2_ENABLE_PORT PORTC // control port for PC0 - - -#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened -#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 -// pin to ADC mappings are in DS table 19-4 -#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 -// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 -#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D -// DS tables 19-3, 19-4 -// Bit 7 6 5 4 3 2 1 0 -// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 -// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 -// divided by ... -// REFS[1:0] = 1, 0 for internal 1.1V reference -// other bits reserved -#define ADMUX_VOLTAGE_DIVIDER 0b10000110 -#define ADC_PRSCL 0x07 // clk/128 - -// Raw ADC readings at 4.4V and 2.2V -// calibrate the voltage readout here -// estimated / calculated values are: -// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) -// D1, R1, R2 = 0, 330, 100 -#ifndef ADC_44 -//#define ADC_44 981 // raw value at 4.40V -#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 -#endif -#ifndef ADC_22 -//#define ADC_22 489 // raw value at 2.20V -#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -#define BUTTON_LED_PIN PA2 // pin 5 -#define BUTTON_LED_PORT PORTA // for all "PA" pins -#define BUTTON_LED_DDR DDRA // for all "PA" pins -#define BUTTON_LED_PUE PUEA // for all "PA" pins - -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead -inline void hwdef_setup() { - // enable output ports - // boost PMIC on/off - DDRC = (1 << LED2_ENABLE_PIN); - // Opamp level and Opamp on/off - DDRB = (1 << PWM1_PIN) - | (1 << LED_ENABLE_PIN); - // aux R/G/B, button LED - DDRA = (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 0,0: PWM OC1B disabled (DS table 12-4) - TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) - | (0<<COM1B1) | (0<<COM1B0) // PWM 1B disabled (DS table 12-4) - ; - TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) - | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) - ; - - // set PWM resolution - PWM1_TOP = PWM_TOP; - - // set up e-switch - ////PORTB = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? - //PUEB = (1 << SWITCH_PIN); // pull-up for e-switch - //PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? - PUEA = (1 << SWITCH_PIN); // pull-up for e-switch - SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt -} - -#define LAYOUT_DEFINED - diff --git a/hwdef-noctigon-dm11-boost.c b/hwdef-noctigon-dm11-boost.c new file mode 100644 index 0000000..2ea8f07 --- /dev/null +++ b/hwdef-noctigon-dm11-boost.c @@ -0,0 +1,47 @@ +// Noctigon DM11 (boost driver) PWM helper functions +// Copyright (C) 2023 Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later + +#pragma once + +#include "chan-rgbaux.c" + +// single set of LEDs with single power channel, boost +void set_level_main(uint8_t level) { + if (level == 0) { + CH1_PWM = 0; + PWM_CNT = 0; // reset phase + LED_ENABLE_PORT &= ~(1 << LED_ENABLE_PIN ); // disable opamp + LED_ENABLE_PORT2 &= ~(1 << LED_ENABLE_PIN2); // disable PMIC + return; + } + + LED_ENABLE_PORT |= (1 << LED_ENABLE_PIN ); // enable opamp + LED_ENABLE_PORT2 |= (1 << LED_ENABLE_PIN2); // enable PMIC + + level --; // PWM array index = level - 1 + PWM_DATATYPE ch1_pwm = PWM_GET(pwm1_levels, level); + // pulse frequency modulation, a.k.a. dynamic PWM + uint16_t top = PWM_GET16(pwm_tops, level); + + CH1_PWM = ch1_pwm; + // wait to sync the counter and avoid flashes + while(actual_level && (PWM_CNT > (top - 32))) {} + PWM_TOP = top; + // force reset phase when turning on from zero + // (because otherwise the initial response is inconsistent) + if (! actual_level) PWM_CNT = 0; +} + +bool gradual_tick_main(uint8_t gt) { + PWM_DATATYPE pwm1 = PWM_GET(pwm1_levels, gt); + + GRADUAL_ADJUST_SIMPLE(pwm1, CH1_PWM); + + if ( (pwm1 == CH1_PWM) + ) { + return true; // done + } + return false; // not done yet +} + diff --git a/hwdef-noctigon-dm11-boost.h b/hwdef-noctigon-dm11-boost.h new file mode 100644 index 0000000..e4d009d --- /dev/null +++ b/hwdef-noctigon-dm11-boost.h @@ -0,0 +1,226 @@ +// Noctigon DM11 boost driver layout (attiny1634) +// Copyright (C) 2021-2023 Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later +#pragma once + +/* + * (based on Noctigon K1) + * + * Pin / Name / Function + * 1 PA6 (none) (PWM1B) (reserved for DD drivers) + * 2 PA5 R: red aux LED (PWM0B) + * 3 PA4 G: green aux LED + * 4 PA3 B: blue aux LED + * 5 PA2 L: button LED + * 6 PA1 (none) + * 7 PA0 (none) + * 8 GND GND + * 9 VCC VCC + * 10 PC5 (none) + * 11 PC4 (none) + * 12 PC3 RESET + * 13 PC2 (none) + * 14 PC1 SCK + * 15 PC0 boost PMIC enable (PWM0A not used) + * 16 PB3 main LED PWM (PWM1A) + * 17 PB2 MISO (PCINT10) + * 18 PB1 MOSI / battery voltage (ADC6) + * 19 PB0 Opamp power + * 20 PA7 e-switch (PCINT7) + * ADC12 thermal sensor + * + * Main LED power uses one pin to turn the Opamp on/off, + * and one pin to control Opamp power level. + * Linear brightness control uses the power level pin, with dynamic PWM. + * The on/off pin is only used to turn the main LED on and off, + * not to change brightness. + */ + +#define ATTINY 1634 +#include <avr/io.h> + +#define HWDEF_C_FILE hwdef-noctigon-dm11-boost.c + +// allow using aux LEDs as extra channel modes +#include "chan-rgbaux.h" + +#define USE_CHANNEL_MODES +// channel modes: +// * 0. main LEDs +// * 1. aux red +// * 2. aux yellow +// * 3. aux green +// * 4. aux cyan +// * 5. aux blue +// * 6. aux purple +// * 7. aux white +#define NUM_CHANNEL_MODES 8 +enum CHANNEL_MODES { + CM_MAIN = 0, + CM_AUXRED, + CM_AUXYEL, + CM_AUXGRN, + CM_AUXCYN, + CM_AUXBLU, + CM_AUXPRP, + CM_AUXWHT, +}; + +#define DEFAULT_CHANNEL_MODE CM_MAIN + +#define CHANNEL_MODES_ENABLED 0b00000001 +#define CHANNEL_HAS_ARGS 0b00000000 +// no args +//#define USE_CHANNEL_MODE_ARGS +//#define CHANNEL_MODE_ARGS 0,0,0,0,0,0,0,0 + +#define SET_LEVEL_MODES set_level_main, \ + set_level_auxred, \ + set_level_auxyel, \ + set_level_auxgrn, \ + set_level_auxcyn, \ + set_level_auxblu, \ + set_level_auxprp, \ + set_level_auxwht +// gradual ticking for thermal regulation +#define GRADUAL_TICK_MODES gradual_tick_main, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null, \ + gradual_tick_null + + +#define PWM_CHANNELS 1 // old, remove this + +#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255 +#define PWM_GET PWM_GET8 +#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255) +#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255 +#define PWM1_DATATYPE uint8_t // 1x7135 ramp + +#define PWM_TOP ICR1 // holds the TOP value for for variable-resolution PWM +#define PWM_TOP_INIT 255 // highest value used in top half of ramp +#define PWM_CNT TCNT1 // for dynamic PWM, reset phase + +#define CH1_PIN PB3 // pin 16, Opamp reference +#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3 + +#define PWM1_PHASE_RESET_OFF // force reset while shutting off +#define PWM1_PHASE_RESET_ON // force reset while turning on +#define PWM1_PHASE_SYNC // manual sync while changing level + +#define LED_ENABLE_PIN PB0 // pin 19, Opamp power +#define LED_ENABLE_PORT PORTB // control port for PB0 + +#define LED_ENABLE_PIN2 PC0 // pin 15, boost PMIC enable +#define LED_ENABLE_PORT2 PORTC // control port for PC0 + +// e-switch +#define SWITCH_PIN PA7 // pin 20 +#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt +#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] +#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] +#define SWITCH_PORT PINA // PINA or PINB or PINC +#define SWITCH_PUE PUEA // pullup group A +#define PCINT_vect PCINT0_vect // ISR for PCINT[7:0] + +#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened +#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 +// pin to ADC mappings are in DS table 19-4 +#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 +// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 +#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D +// DS tables 19-3, 19-4 +// Bit 7 6 5 4 3 2 1 0 +// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 +// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 +// divided by ... +// REFS[1:0] = 1, 0 for internal 1.1V reference +// other bits reserved +#define ADMUX_VOLTAGE_DIVIDER 0b10000110 +#define ADC_PRSCL 0x07 // clk/128 + +// Raw ADC readings at 4.4V and 2.2V +// calibrate the voltage readout here +// estimated / calculated values are: +// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) +// D1, R1, R2 = 0, 330, 100 +#ifndef ADC_44 +//#define ADC_44 981 // raw value at 4.40V +#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 +#endif +#ifndef ADC_22 +//#define ADC_22 489 // raw value at 2.20V +#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 +#endif + +// this light has aux LEDs under the optic +#define AUXLED_R_PIN PA5 // pin 2 +#define AUXLED_G_PIN PA4 // pin 3 +#define AUXLED_B_PIN PA3 // pin 4 +#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC +#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC +#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC + +#define BUTTON_LED_PIN PA2 // pin 5 +#define BUTTON_LED_PORT PORTA // for all "PA" pins +#define BUTTON_LED_DDR DDRA // for all "PA" pins +#define BUTTON_LED_PUE PUEA // for all "PA" pins + +// this light has three aux LED channels: R, G, B +#define USE_AUX_RGB_LEDS +// it also has an independent LED in the button +#define USE_BUTTON_LED +// the aux LEDs are front-facing, so turn them off while main LEDs are on +#ifdef USE_INDICATOR_LED_WHILE_RAMPING +#undef USE_INDICATOR_LED_WHILE_RAMPING +#endif + +void set_level_main(uint8_t level); + +bool gradual_tick_main(uint8_t gt); + + +inline void hwdef_setup() { + // enable output ports + // boost PMIC on/off + DDRC = (1 << LED_ENABLE_PIN2); + // Opamp level and Opamp on/off + DDRB = (1 << CH1_PIN) + | (1 << LED_ENABLE_PIN); + // aux R/G/B, button LED + DDRA = (1 << AUXLED_R_PIN) + | (1 << AUXLED_G_PIN) + | (1 << AUXLED_B_PIN) + | (1 << BUTTON_LED_PIN) + ; + + // configure PWM + // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter + // pre-scale for timer: N = 1 + // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) + // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) + // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) + // COM1B[1:0]: 0,0: PWM OC1B disabled (DS table 12-4) + TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) + | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) + | (0<<COM1B1) | (0<<COM1B0) // PWM 1B disabled (DS table 12-4) + ; + TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) + | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) + ; + + // set PWM resolution + PWM_TOP = PWM_TOP_INIT; + + // set up e-switch + SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch + SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt +} + + +#define LAYOUT_DEFINED + diff --git a/spaghetti-monster/anduril/MODELS b/spaghetti-monster/anduril/MODELS index 3a321cd..efe4a05 100644 --- a/spaghetti-monster/anduril/MODELS +++ b/spaghetti-monster/anduril/MODELS @@ -38,7 +38,8 @@ Model Name MCU 0267 noctigon-k9.3-tintramp-219 attiny1634 0271 noctigon-dm11 attiny1634 0272 noctigon-dm11-nofet attiny1634 -0273 noctigon-dm11-12v attiny1634 +0273 noctigon-dm11-boost attiny1634 +0273 noctigon-dm11-12v attiny1634 (old) 0274 noctigon-dm11-sbt90 attiny1634 0311 fw3a attiny85 0312 fw3a-219 attiny85 diff --git a/spaghetti-monster/anduril/cfg-noctigon-dm11-12v.h b/spaghetti-monster/anduril/cfg-noctigon-dm11-boost.h index 7798206..231944c 100644 --- a/spaghetti-monster/anduril/cfg-noctigon-dm11-12v.h +++ b/spaghetti-monster/anduril/cfg-noctigon-dm11-boost.h @@ -1,28 +1,18 @@ -// Noctigon DM11 (12V) config options for Anduril +// Noctigon DM11 (boost driver) config options for Anduril // Copyright (C) 2021-2023 Selene ToyKeeper // SPDX-License-Identifier: GPL-3.0-or-later #pragma once #define MODEL_NUMBER "0273" -#include "hwdef-Noctigon_DM11-12V.h" +#include "hwdef-noctigon-dm11-boost.h" #include "hank-cfg.h" // ATTINY: 1634 -// this light has three aux LED channels: R, G, B -#define USE_AUX_RGB_LEDS -// ... and a single LED in the button -#define USE_BUTTON_LED -// don't use aux LEDs while main LED is on -#ifdef USE_INDICATOR_LED_WHILE_RAMPING -#undef USE_INDICATOR_LED_WHILE_RAMPING -#endif - +#define RAMP_SIZE 150 // power channels: -// - linear: 5A? +// - boost: 8A? // - DD FET: none (can't do DD on a boost driver) -#define RAMP_LENGTH 150 -#define USE_DYN_PWM // level_calc.py 5.01 1 149 7135 1 0.3 1740 --pwm dyn:78:16384:255 // (plus a 0 at the beginning for moon) @@ -34,11 +24,6 @@ #define HALFSPEED_LEVEL 12 #define QUARTERSPEED_LEVEL 4 -// don't blink halfway up -#ifdef BLINK_AT_RAMP_MIDDLE -#undef BLINK_AT_RAMP_MIDDLE -#endif - #define RAMP_SMOOTH_FLOOR 10 // low levels may be unreliable #define RAMP_SMOOTH_CEIL 130 // 10, 30, 50, [70], 90, 110, 130 @@ -52,21 +37,33 @@ #define SIMPLE_UI_CEIL RAMP_DISCRETE_CEIL #define SIMPLE_UI_STEPS 5 -// make candle mode wobble more -#define CANDLE_AMPLITUDE 33 - // stop panicking at ~70% power or ~600 lm #define THERM_FASTER_LEVEL 130 #define MIN_THERM_STEPDOWN 80 // must be > end of dynamic PWM range +#define THERM_CAL_OFFSET 5 + //#define THERM_RESPONSE_MAGNITUDE 32 // smaller adjustments, this host changes temperature slowly //#define THERM_NEXT_WARNING_THRESHOLD 32 // more error tolerance before adjusting +// show each channel while it scroll by in the menu +#define USE_CONFIG_COLORS + +// blink numbers on the aux LEDs by default +#define DEFAULT_BLINK_CHANNEL CM_AUXWHT + +// use aux red + aux blue for police strobe +#define USE_POLICE_COLOR_STROBE_MODE +#define POLICE_STROBE_USES_AUX +#define POLICE_COLOR_STROBE_CH1 CM_AUXRED +#define POLICE_COLOR_STROBE_CH2 CM_AUXBLU + +// the default of 26 looks a bit rough, so increase it to make it smoother +#define CANDLE_AMPLITUDE 33 + // slow down party strobe; this driver can't pulse for 2ms or less #define PARTY_STROBE_ONTIME 3 -#define THERM_CAL_OFFSET 5 - // the power regulator seems to "jump start" the LEDs all on its own, // so the firmware doesn't have to // (and unfortunately the power regulator jumps it a bit too hard) @@ -77,3 +74,8 @@ // added for convenience #define USE_SOFT_FACTORY_RESET +// don't blink halfway up +#ifdef BLINK_AT_RAMP_MIDDLE +#undef BLINK_AT_RAMP_MIDDLE +#endif + |