diff options
Diffstat (limited to 'hw/sofirn/blf-q8-t1616')
| -rw-r--r-- | hw/sofirn/blf-q8-t1616/cfg.h | 82 | ||||
| -rw-r--r-- | hw/sofirn/blf-q8-t1616/hwdef.h | 138 |
2 files changed, 220 insertions, 0 deletions
diff --git a/hw/sofirn/blf-q8-t1616/cfg.h b/hw/sofirn/blf-q8-t1616/cfg.h new file mode 100644 index 0000000..9f0402c --- /dev/null +++ b/hw/sofirn/blf-q8-t1616/cfg.h @@ -0,0 +1,82 @@ +// BLF Q8 config options for Anduril using the Attiny1616 +// Copyright (C) 2021-2023 gchart, Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later +#pragma once + +#define MODEL_NUMBER "0613" +#include "hwdef-blf-q8-t1616.h" +#include "wurkkos-cfg.h" // Sofirn lights are closely related to Wurkkos +// ATTINY: 1616 + +// the button lights up +#define USE_INDICATOR_LED +// the button is visible while main LEDs are on +#define USE_INDICATOR_LED_WHILE_RAMPING +// off mode: low (1) +// lockout: blinking (3) +#define INDICATOR_LED_DEFAULT_MODE ((3<<2) + 1) + +// copied from Wurkkos TS25 ramp +#define RAMP_SIZE 150 +// 7135 at 75/150 +// level_calc.py 5.7895 2 150 7135 1 0.1 130 FET 1 10 3000 --pwm dyn:74:4096:255:3 +// (with some manual tweaks) +#define PWM1_LEVELS 1,1,2,3,3,4,5,6,7,8,9,11,12,13,15,16,18,19,21,23,26,27,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,71,74,76,78,80,82,85,87,90,93,96,100,103,107,112,116,122,127,133,140,147,154,163,171,182,192,203,215,228,241,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,0 +// non-zero part of FET channel calculated with: +// level_calc.py 3 1 75 7135 1 200 3000 +// (FIXME? there's a visible bump when the FET kicks in, even with just 1/255) +#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,2,3,4,6,7,8,10,11,13,14,16,17,19,21,22,24,26,28,30,32,34,37,39,41,44,46,48,51,54,56,59,62,65,68,71,74,77,81,84,87,91,94,98,102,106,110,114,118,122,126,130,135,139,144,148,153,158,163,168,173,178,184,189,195,200,206,212,218,224,230,236,242,248,255 +#define PWM_TOPS 4095,2701,3200,3586,2518,2778,2834,2795,2705,2587,2455,2582,2412,2247,2256,2091,2062,1907,1860,1802,1737,1605,1542,1477,1412,1347,1284,1222,1162,1105,1050,997,946,898,853,810,768,730,693,658,625,594,564,536,503,485,462,439,418,398,384,366,353,340,327,319,307,298,292,284,280,273,269,266,263,260,258,256,256,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255 + +#define MAX_1x7135 75 +#define DEFAULT_LEVEL 50 +#define MIN_THERM_STEPDOWN 60 +#define HALFSPEED_LEVEL 20 +#define QUARTERSPEED_LEVEL 5 + +#define RAMP_SMOOTH_FLOOR 1 +#define RAMP_SMOOTH_CEIL 150 +// 20 38 56 [75] 93 111 130 +#define RAMP_DISCRETE_FLOOR 20 +#define RAMP_DISCRETE_CEIL 130 +#define RAMP_DISCRETE_STEPS 7 + +// at Sofirn's request, use max (150) for the Simple UI ceiling +#define SIMPLE_UI_FLOOR 1 +#define SIMPLE_UI_CEIL 150 +#define SIMPLE_UI_STEPS 5 + +// also at Sofirn's request, enable 2 click turbo (Anduril 1 style) +#define DEFAULT_2C_STYLE 1 + +// enable SOS in the blinkies group +#define USE_SOS_MODE +#define USE_SOS_MODE_IN_BLINKY_GROUP + +// Allow 3C in Simple UI for switching between smooth and stepped ramping +#define USE_SIMPLE_UI_RAMPING_TOGGLE + +// allow Aux Config and Strobe Modes in Simple UI +#define USE_EXTENDED_SIMPLE_UI + +// stop panicking at ~75% power or ~3000 lm, this light has high thermal mass +#define THERM_FASTER_LEVEL (RAMP_SIZE*9/10) // throttle back faster when high + +// show each channel while it scroll by in the menu +#define USE_CONFIG_COLORS + +// blink numbers on the aux LEDs by default +#define DEFAULT_BLINK_CHANNEL CM_AUX + +// the default of 26 looks a bit rough, so increase it to make it smoother +#define CANDLE_AMPLITUDE 33 + +// don't blink during the ramp; the button LED brightness is sufficient +// to indicate which power channel(s) are being used +#ifdef BLINK_AT_RAMP_MIDDLE +#undef BLINK_AT_RAMP_MIDDLE +#endif + +// enable factory reset on 13H without loosening tailcap (required) +#define USE_SOFT_FACTORY_RESET + diff --git a/hw/sofirn/blf-q8-t1616/hwdef.h b/hw/sofirn/blf-q8-t1616/hwdef.h new file mode 100644 index 0000000..d9b981f --- /dev/null +++ b/hw/sofirn/blf-q8-t1616/hwdef.h @@ -0,0 +1,138 @@ +// BLF Q8 driver layout using the Attiny1616 +// Copyright (C) 2021-2023 gchart, Selene ToyKeeper +// SPDX-License-Identifier: GPL-3.0-or-later +#pragma once + +/* + * (based on Wurkkos TS10 driver layout, + * which in turn was based on an older version of this BLF-Q8-t1616 driver) + * (should probably merge the two files at some point) + * Driver pinout: + * eSwitch: PA5 + * Aux LED: PB5 + * PWM FET: PB0 (TCA0 WO0) + * PWM 1x7135: PB1 (TCA0 WO1) + * Voltage: VCC + */ + +#define ATTINY 1616 +#include <avr/io.h> + +// nearly all t1616-based FET+1 drivers work pretty much the same +// (this one has single-color aux like the TS10) +#define HWDEF_C_FILE hwdef-wurkkos-ts10.c + +// allow using aux LEDs as extra channel modes +#include "chan-aux.h" + +// channel modes: +// * 0. FET+7135 stacked +// * 1. aux LEDs +#define NUM_CHANNEL_MODES 2 +enum CHANNEL_MODES { + CM_MAIN = 0, + CM_AUX +}; + +#define DEFAULT_CHANNEL_MODE CM_MAIN + +// right-most bit first, modes are in fedcba9876543210 order +#define CHANNEL_MODES_ENABLED 0b00000001 + + +#define PWM_CHANNELS 2 // old, remove this + +#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255 +#define PWM_GET PWM_GET8 +#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255) +#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255 +#define PWM1_DATATYPE uint8_t // 1x7135 ramp +#define PWM2_DATATYPE uint8_t // DD FET ramp + +// PWM parameters of both channels are tied together because they share a counter +#define PWM_TOP TCA0.SINGLE.PERBUF // holds the TOP value for for variable-resolution PWM +#define PWM_TOP_INIT 255 // highest value used in top half of ramp +// not necessary when double-buffered "BUF" registers are used +#define PWM_CNT TCA0.SINGLE.CNT // for resetting phase after each TOP adjustment + +// 1x7135 channel +#define CH1_PIN PB1 +#define CH1_PWM TCA0.SINGLE.CMP1BUF // CMP1 is the output compare register for PB1 + +// DD FET channel +#define CH2_PIN PB0 +#define CH2_PWM TCA0.SINGLE.CMP0BUF // CMP0 is the output compare register for PB0 + +// e-switch +#define SWITCH_PIN PIN5_bp +#define SWITCH_PORT VPORTA.IN +#define SWITCH_ISC_REG PORTA.PIN2CTRL +#define SWITCH_VECT PORTA_PORT_vect +#define SWITCH_INTFLG VPORTA.INTFLAGS + +// average drop across diode on this hardware +#ifndef VOLTAGE_FUDGE_FACTOR +#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V +#endif + +// lighted button +#define AUXLED_PIN PIN5_bp +#define AUXLED_PORT PORTB + + +inline void hwdef_setup() { + + // set up the system clock to run at 10 MHz instead of the default 3.33 MHz + _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, + CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm ); + + //VPORTA.DIR = ...; + // Outputs + VPORTB.DIR = PIN0_bm // DD FET + | PIN1_bm // 7135 + | PIN5_bm; // Aux LED + //VPORTC.DIR = ...; + + // enable pullups on the unused pins to reduce power + PORTA.PIN0CTRL = PORT_PULLUPEN_bm; + PORTA.PIN1CTRL = PORT_PULLUPEN_bm; + PORTA.PIN2CTRL = PORT_PULLUPEN_bm; + PORTA.PIN3CTRL = PORT_PULLUPEN_bm; + PORTA.PIN4CTRL = PORT_PULLUPEN_bm; + PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc; // eSwitch + PORTA.PIN6CTRL = PORT_PULLUPEN_bm; + PORTA.PIN7CTRL = PORT_PULLUPEN_bm; + + //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel + //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel + PORTB.PIN2CTRL = PORT_PULLUPEN_bm; + PORTB.PIN3CTRL = PORT_PULLUPEN_bm; + PORTB.PIN4CTRL = PORT_PULLUPEN_bm; + //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED + + PORTC.PIN0CTRL = PORT_PULLUPEN_bm; + PORTC.PIN1CTRL = PORT_PULLUPEN_bm; + PORTC.PIN2CTRL = PORT_PULLUPEN_bm; + PORTC.PIN3CTRL = PORT_PULLUPEN_bm; + + // set up the PWM + // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf + // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm + // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm + // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm + // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc + // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc + // See the manual for other pins, clocks, configs, portmux, etc + TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm + | TCA_SINGLE_CMP1EN_bm + | TCA_SINGLE_WGMODE_DSBOTTOM_gc; + TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc + | TCA_SINGLE_ENABLE_bm; + + PWM_TOP = PWM_TOP_INIT; + +} + + +#define LAYOUT_DEFINED + |