diff options
Diffstat (limited to 'hwdef-Emisar_D4Sv2.h')
| -rw-r--r-- | hwdef-Emisar_D4Sv2.h | 122 |
1 files changed, 0 insertions, 122 deletions
diff --git a/hwdef-Emisar_D4Sv2.h b/hwdef-Emisar_D4Sv2.h deleted file mode 100644 index d68b7ac..0000000 --- a/hwdef-Emisar_D4Sv2.h +++ /dev/null @@ -1,122 +0,0 @@ -#ifndef HWDEF_EMISAR_D4SV2_H -#define HWDEF_EMISAR_D4SV2_H - -/* Emisar D4Sv2 driver layout (attiny1634) - * (same layout as D4v2, except it's a FET+3+1 instead of FET+1) - * - * Pin / Name / Function - * 1 PA6 FET PWM (PWM1B) - * 2 PA5 red aux LED (PWM0B) - * 3 PA4 green aux LED - * 4 PA3 blue aux LED - * 5 PA2 e-switch - * 6 PA1 (none) - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 3x7135 PWM (PWM0A) - * 16 PB3 1x7135 PWM (PWM1A) - * 17 PB2 MISO - * 18 PB1 MOSI - * 19 PB0 (none) - * 20 PA7 (none) - * ADC12 thermal sensor - */ - -#ifdef ATTINY -#undef ATTINY -#endif -#define ATTINY 1634 -#include <avr/io.h> - -#define SWITCH_PIN PA2 // pin 5 -#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC - -#define PWM_CHANNELS 3 - -#define PWM1_PIN PB3 // pin 16, 1x7135 PWM -#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3 - -#define PWM2_PIN PC0 // pin 15, 3x7135 PWM -#define PWM2_LVL OCR0A // OCR0A is the output compare register for PC0 - -#define PWM3_PIN PA6 // pin 1, FET PWM -#define PWM3_LVL OCR1B // OCR1B is the output compare register for PB1 - - -#define ADC_PRSCL 0x07 // clk/128 - -// average drop across diode on this hardware -#ifndef VOLTAGE_FUDGE_FACTOR -#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V) -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead -inline void hwdef_setup() { - // enable output ports - // FET, aux R/G/B - DDRA = (1 << PWM3_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - ; - // 1x7135 - DDRB = (1 << PWM1_PIN); - // 3x7135 - DDRC = (1 << PWM2_PIN); - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // WGM1[3:0]: 0,0,0,1: PWM, Phase Correct, 8-bit (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (0<<WGM11) | (1<<WGM10) // 8-bit (TOP=0xFF) (DS table 12-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) - | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) - ; - TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) - | (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5) - ; - - // WGM0[2:0]: 0,0,1: PWM, Phase Correct (DS table 11-8) - // CS0[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 11-9) - // COM0A[1:0]: 1,0: PWM OC0A in the normal direction (DS table 11-4) - // COM0B[1:0]: 0,0: OC0B disabled (DS table 11-7) - // TCCR0A: COM0A1, COM0A0, COM0B1, COM0B0, -, -, WGM01, WGM00 - TCCR0A = (0<<WGM01) | (1<<WGM00) // PWM, Phase Correct, TOP=0xFF (DS table 11-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 0A in normal direction (DS table 11-4) - | (0<<COM1B1) | (0<<COM1B0) // PWM 0B disabled (DS table 11-7) - ; - // TCCR0B: FOC0A, FOC0B, -, -, WGM02, CS02, CS01, CS00 - TCCR0B = (0<<CS02) | (0<<CS01) | (1<<CS00) // clk/1 (no prescaling) (DS table 11-9) - | (0<<WGM02) // PWM, Phase Correct, TOP=0xFF (DS table 11-8) - ; - - // set up e-switch - //PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? - PUEA = (1 << SWITCH_PIN); // pull-up for e-switch - SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt -} - -#define LAYOUT_DEFINED - -#endif |