diff options
Diffstat (limited to 'hwdef-Emisar_D4v2.h')
| -rw-r--r-- | hwdef-Emisar_D4v2.h | 129 |
1 files changed, 0 insertions, 129 deletions
diff --git a/hwdef-Emisar_D4v2.h b/hwdef-Emisar_D4v2.h deleted file mode 100644 index 2864cd4..0000000 --- a/hwdef-Emisar_D4v2.h +++ /dev/null @@ -1,129 +0,0 @@ -// hwdef for Emisar D4v2 (attiny1634) -// Copyright (C) 2018 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * Pin / Name / Function - * 1 PA6 FET PWM (PWM1B) - * 2 PA5 red aux LED (PWM0B) - * 3 PA4 green aux LED - * 4 PA3 blue aux LED - * 5 PA2 e-switch - * 6 PA1 button LED - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 (none) PWM0A - * 16 PB3 7135 PWM (PWM1A) - * 17 PB2 MISO - * 18 PB1 MOSI - * 19 PB0 (none) - * 20 PA7 (none) - * ADC12 thermal sensor - */ - -#ifdef ATTINY -#undef ATTINY -#endif -#define ATTINY 1634 -#include <avr/io.h> - -// TODO: add aux red and aux blue as disabled channel modes, -// so they can be used for the police strobe? -#define NUM_CHANNEL_MODES 1 -#define DEFAULT_CHANNEL_MODE 0 -#define SET_LEVEL_MODES set_level_2ch_stacked -#define GRADUAL_TICK_MODES gradual_tick_2ch_stacked -// no special handlers needed, can use common handlers -#define USE_SET_LEVEL_2CH_STACKED -#define USE_GRADUAL_TICK_2CH_STACKED - -#define PWM_CHANNELS 2 - -#define SWITCH_PIN PA2 // pin 5 -#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC - -#define LOW_PWM_PIN PB3 // pin 16, 1x7135 PWM -#define LOW_PWM_LVL OCR1A // OCR1A is the output compare register for PB3 -#define PWM1_BITS 8 - -#define HIGH_PWM_PIN PA6 // pin 1, FET PWM -#define HIGH_PWM_LVL OCR1B // OCR1B is the output compare register for PB1 -#define PWM2_BITS 8 - -// only using 8-bit on this light -#define PWM_GET PWM_GET8 -#define PWM_DATATYPE uint8_t - -#define ADC_PRSCL 0x07 // clk/128 - -// average drop across diode on this hardware -#ifndef VOLTAGE_FUDGE_FACTOR -#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V) -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -#define BUTTON_LED_PIN PA1 // pin 6 -#define BUTTON_LED_PORT PORTA // for all "PA" pins -#define BUTTON_LED_DDR DDRA // for all "PA" pins -#define BUTTON_LED_PUE PUEA // for all "PA" pins - -// this light has three aux LED channels: R, G, B -#define USE_AUX_RGB_LEDS -// it also has an independent LED in the button -#define USE_BUTTON_LED -// the aux LEDs are front-facing, so turn them off while main LEDs are on -// TODO: the whole "indicator LED" thing needs to be refactored into -// "aux LED(s)" and "button LED(s)" since they work a bit differently -#ifdef USE_INDICATOR_LED_WHILE_RAMPING -#undef USE_INDICATOR_LED_WHILE_RAMPING -#endif - -inline void hwdef_setup() { - // enable output ports - // 7135 - DDRB = (1 << LOW_PWM_PIN); - // FET, aux R/G/B, button LED - DDRA = (1 << HIGH_PWM_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - TCCR1A = (0<<WGM11) | (1<<WGM10) // 8-bit (TOP=0xFF) (DS table 12-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) - | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) - ; - TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) - | (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5) - ; - - // set up e-switch - //PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC? - PUEA = (1 << SWITCH_PIN); // pull-up for e-switch - SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt -} - - -#define LAYOUT_DEFINED - |