1 files changed, 0 insertions, 115 deletions
diff --git a/hwdef-Wurkkos_TS10.h b/hwdef-Wurkkos_TS10.h
deleted file mode 100644
index 1d138be..0000000
--- a/hwdef-Wurkkos_TS10.h
+++ /dev/null
@@ -1,115 +0,0 @@
-// Wurkkos TS10 driver layout
-// Copyright (C) 2022-2023 (FIXME)
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * (based on BLF Q8-t1616 driver layout)
- * Driver pinout:
- * eSwitch:    PA5
- * Aux LED:    PB5
- * PWM FET:    PB0 (TCA0 WO0)
- * PWM 1x7135: PB1 (TCA0 WO1)
- * Voltage:    VCC
- */
-
-#define LAYOUT_DEFINED
-
-#ifdef ATTINY
-#undef ATTINY
-#endif
-#define ATTINY 1616
-#include <avr/io.h>
-
-#define PWM_CHANNELS 2
-#define PWM_BITS 16
-#define PWM_TOP 255
-#define USE_DYN_PWM
-
-#ifndef SWITCH_PIN
-#define SWITCH_PIN     PIN5_bp
-#define SWITCH_PORT    VPORTA.IN
-#define SWITCH_ISC_REG PORTA.PIN2CTRL
-#define SWITCH_VECT    PORTA_PORT_vect
-#define SWITCH_INTFLG  VPORTA.INTFLAGS
-#endif
-
-
-// 7135 channel
-#ifndef PWM1_PIN
-#define PWM1_PIN PB1               //
-#define PWM1_LVL TCA0.SINGLE.CMP1BUF  // CMP1 is the output compare register for PB1
-#endif
-
-// FET channel
-#ifndef PWM2_PIN
-#define PWM2_PIN PB0               //
-#define PWM2_LVL TCA0.SINGLE.CMP0BUF  // CMP0 is the output compare register for PB0
-#endif
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM1_TOP TCA0.SINGLE.PERBUF   // holds the TOP value for for variable-resolution PWM
-// not necessary when double-buffered "BUF" registers are used
-#define PWM1_CNT TCA0.SINGLE.CNT   // for resetting phase after each TOP adjustment
-#define PWM1_PHASE_RESET_OFF  // force reset while shutting off
-#define PWM1_PHASE_RESET_ON   // force reset while turning on
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 7  // add 0.35V
-#endif
-
-
-// lighted button
-#ifndef AUXLED_PIN
-#define AUXLED_PIN  PIN5_bp
-#define AUXLED_PORT PORTB
-#endif
-
-
-// with so many pins, doing this all with #ifdefs gets awkward...
-// ... so just hardcode it in each hwdef file instead
-inline void hwdef_setup() {
-
-    // set up the system clock to run at 10 MHz instead of the default 3.33 MHz
-    _PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
-
-    //VPORTA.DIR = ...;
-    VPORTB.DIR = PIN0_bm | PIN1_bm | PIN5_bm;  // Outputs: Aux LED and PWMs
-    //VPORTC.DIR = ...;
-
-    // enable pullups on the unused pins to reduce power
-    PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc;  // eSwitch
-    PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
-    PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
-
-    //PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
-    //PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
-    PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
-    PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
-    //PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
-
-    PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
-    PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
-
-    // set up the PWM
-    // https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
-    // PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
-    // PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
-    // PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
-    // For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
-    // For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
-    // See the manual for other pins, clocks, configs, portmux, etc
-    TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
-    PWM1_TOP = PWM_TOP;
-    TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
-}
-