diff options
Diffstat (limited to 'hwdef-mateminco-mf01s.h')
| -rw-r--r-- | hwdef-mateminco-mf01s.h | 102 |
1 files changed, 0 insertions, 102 deletions
diff --git a/hwdef-mateminco-mf01s.h b/hwdef-mateminco-mf01s.h deleted file mode 100644 index af214b2..0000000 --- a/hwdef-mateminco-mf01s.h +++ /dev/null @@ -1,102 +0,0 @@ -// Mateminco MT18S / Astrolux MF01S driver layout -// Copyright (C) 2019-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * ---- - * Reset -|1 8|- VCC (unused) - * eswitch -|2 7|- Voltage divider (2S) - * AUX LED -|3 6|- PWM (FET) - * GND -|4 5|- PWM (smaller FET) - * ---- - */ - -#define ATTINY 85 -#include <avr/io.h> - -#define HWDEF_C_FILE hwdef-emisar-d4.c - -// channel modes -// * 0. small FET + big FET stacked -#define NUM_CHANNEL_MODES 1 -enum CHANNEL_MODES { - CM_MAIN = 0, -}; - -#define DEFAULT_CHANNEL_MODE CM_MAIN - -// right-most bit first, modes are in fedcba9876543210 order -#define CHANNEL_MODES_ENABLED 0b00000001 - - -#define PWM_CHANNELS 2 // old, remove this - -#define PWM_BITS 8 // attiny85 only supports up to 8 bits -#define PWM_GET PWM_GET8 -#define PWM_DATATYPE uint8_t -#define PWM_DATATYPE2 uint16_t -#define PWM1_DATATYPE uint8_t // little FET ramp -#define PWM2_DATATYPE uint8_t // big FET ramp - -#define PWM_TOP_INIT 255 // highest value used in top half of ramp - -// little FET channel -#define CH1_PIN PB0 // pin 5, 1x7135 PWM -#define CH1_PWM OCR0A // OCR0A is the output compare register for PB0 - -// big FET channel -#define CH2_PIN PB1 // pin 6, FET PWM -#define CH2_PWM OCR0B // OCR0B is the output compare register for PB1 - -// lighted button and 1-channel front aux -#define AUXLED_PIN PB4 // pin 3 - -// e-switch -#ifndef SWITCH_PIN -#define SWITCH_PIN PB3 // pin 2 -#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt -#endif - -#define USE_VOLTAGE_DIVIDER // use a voltage divider on pin 7, not VCC -#ifndef VOLTAGE_PIN -#define VOLTAGE_PIN PB2 // pin 7, voltage ADC -#define VOLTAGE_CHANNEL 0x01 // MUX 01 corresponds with PB2 -#define VOLTAGE_ADC ADC1D // Digital input disable bit corresponding with PB2 -// inherited from tk-attiny.h -//#define VOLTAGE_ADC_DIDR DIDR0 // DIDR for ADC1 -// 1.1V reference, left-adjust, ADC1/PB2 -//#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | (1 << ADLAR) | VOLTAGE_CHANNEL) -// 1.1V reference, no left-adjust, ADC1/PB2 -#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | VOLTAGE_CHANNEL) -#endif -#define ADC_PRSCL 0x07 // clk/128 - -// Raw ADC readings at 4.4V and 2.2V (in-between, we assume values form a straight line) -#ifndef ADC_44 -#define ADC_44 (234*4) -#endif -#ifndef ADC_22 -#define ADC_22 (117*4) -#endif - -#define FAST 0xA3 // fast PWM both channels -#define PHASE 0xA1 // phase-correct PWM both channels - - -inline void hwdef_setup() { - // configure PWM channels - DDRB = (1 << CH1_PIN) - | (1 << CH2_PIN); - - TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...) - TCCR0A = PHASE; - - // configure e-switch - PORTB = (1 << SWITCH_PIN); // e-switch is the only input - PCMSK = (1 << SWITCH_PIN); // pin change interrupt uses this pin -} - - -#define LAYOUT_DEFINED - |