diff options
Diffstat (limited to 'hwdef-noctigon-dm11-boost.h')
| -rw-r--r-- | hwdef-noctigon-dm11-boost.h | 206 |
1 files changed, 0 insertions, 206 deletions
diff --git a/hwdef-noctigon-dm11-boost.h b/hwdef-noctigon-dm11-boost.h deleted file mode 100644 index d56a5f5..0000000 --- a/hwdef-noctigon-dm11-boost.h +++ /dev/null @@ -1,206 +0,0 @@ -// Noctigon DM11 boost driver layout (attiny1634) -// Copyright (C) 2021-2023 Selene ToyKeeper -// SPDX-License-Identifier: GPL-3.0-or-later -#pragma once - -/* - * (based on Noctigon K1) - * - * Pin / Name / Function - * 1 PA6 (none) (PWM1B) (reserved for DD drivers) - * 2 PA5 R: red aux LED (PWM0B) - * 3 PA4 G: green aux LED - * 4 PA3 B: blue aux LED - * 5 PA2 L: button LED - * 6 PA1 (none) - * 7 PA0 (none) - * 8 GND GND - * 9 VCC VCC - * 10 PC5 (none) - * 11 PC4 (none) - * 12 PC3 RESET - * 13 PC2 (none) - * 14 PC1 SCK - * 15 PC0 boost PMIC enable (PWM0A not used) - * 16 PB3 main LED PWM (PWM1A) - * 17 PB2 MISO (PCINT10) - * 18 PB1 MOSI / battery voltage (ADC6) - * 19 PB0 Opamp power - * 20 PA7 e-switch (PCINT7) - * ADC12 thermal sensor - * - * Main LED power uses one pin to turn the Opamp on/off, - * and one pin to control Opamp power level. - * Regulated brightness control uses the power level pin, with PWM+DSM. - * The on/off pin is only used to turn the main LED on and off, - * not to change brightness. - */ - -#define ATTINY 1634 -#include <avr/io.h> - -#define HWDEF_C_FILE hwdef-noctigon-dm11-boost.c - -// allow using aux LEDs as extra channel modes -#include "chan-rgbaux.h" - -// channel modes: -// * 0. main LEDs -// * 1+. aux RGB -#define NUM_CHANNEL_MODES (1 + NUM_RGB_AUX_CHANNEL_MODES) -enum CHANNEL_MODES { - CM_MAIN = 0, - RGB_AUX_ENUMS -}; - -#define DEFAULT_CHANNEL_MODE CM_MAIN - -// right-most bit first, modes are in fedcba9876543210 order -#define CHANNEL_MODES_ENABLED 0b0000000000000001 -// no args -//#define USE_CHANNEL_MODE_ARGS -//#define CHANNEL_MODE_ARGS 0,0,0,0,0,0,0,0 - - -#define PWM_CHANNELS 1 // old, remove this - -#define PWM_BITS 16 // 0 to 32640 (0 to 255 PWM + 0 to 127 DSM) at constant kHz -#define PWM_GET PWM_GET16 -#define PWM_DATATYPE uint16_t -#define PWM_DATATYPE2 uint32_t // only needs 32-bit if ramp values go over 255 -#define PWM1_DATATYPE uint16_t // 15-bit PWM+DSM ramp - -#define PWM_TOP ICR1 // holds the TOP value for variable-resolution PWM -#define PWM_TOP_INIT 255 -#define PWM_CNT TCNT1 // for checking / resetting phase -// (max is (255 << 7), because it's 8-bit PWM plus 7 bits of DSM) -#define DSM_TOP (255<<7) // 15-bit resolution leaves 1 bit for carry - -// timer interrupt for DSM -#define DSM_vect TIMER1_OVF_vect -#define DSM_INTCTRL TIMSK -#define DSM_OVF_bm (1<<TOIE1) - -#define DELAY_FACTOR 90 // less time in delay() because more time spent in interrupts - -// regulated channel -uint16_t ch1_dsm_lvl; -uint8_t ch1_pwm, ch1_dsm; -#define CH1_PIN PB3 // pin 16, Opamp reference -#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3 - -#define CH1_ENABLE_PIN PB0 // pin 19, Opamp power -#define CH1_ENABLE_PORT PORTB // control port for PB0 - -#define CH1_ENABLE_PIN2 PC0 // pin 15, boost PMIC enable -#define CH1_ENABLE_PORT2 PORTC // control port for PC0 - -// e-switch -#define SWITCH_PIN PA7 // pin 20 -#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt -#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0] -#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0] -#define SWITCH_PORT PINA // PINA or PINB or PINC -#define SWITCH_PUE PUEA // pullup group A -#define PCINT_vect PCINT0_vect // ISR for PCINT[7:0] - -#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened -#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6 -// pin to ADC mappings are in DS table 19-4 -#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1 -// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6 -#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D -// DS tables 19-3, 19-4 -// Bit 7 6 5 4 3 2 1 0 -// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0 -// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1 -// divided by ... -// REFS[1:0] = 1, 0 for internal 1.1V reference -// other bits reserved -#define ADMUX_VOLTAGE_DIVIDER 0b10000110 -#define ADC_PRSCL 0x07 // clk/128 - -// Raw ADC readings at 4.4V and 2.2V -// calibrate the voltage readout here -// estimated / calculated values are: -// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1) -// D1, R1, R2 = 0, 330, 100 -#ifndef ADC_44 -//#define ADC_44 981 // raw value at 4.40V -#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2 -#endif -#ifndef ADC_22 -//#define ADC_22 489 // raw value at 2.20V -#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2 -#endif - -// this light has aux LEDs under the optic -#define AUXLED_R_PIN PA5 // pin 2 -#define AUXLED_G_PIN PA4 // pin 3 -#define AUXLED_B_PIN PA3 // pin 4 -#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC -#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC -#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC - -#define BUTTON_LED_PIN PA2 // pin 5 -#define BUTTON_LED_PORT PORTA // for all "PA" pins -#define BUTTON_LED_DDR DDRA // for all "PA" pins -#define BUTTON_LED_PUE PUEA // for all "PA" pins - -// this light has three aux LED channels: R, G, B -#define USE_AUX_RGB_LEDS -// it also has an independent LED in the button -#define USE_BUTTON_LED -// the aux LEDs are front-facing, so turn them off while main LEDs are on -#ifdef USE_INDICATOR_LED_WHILE_RAMPING -#undef USE_INDICATOR_LED_WHILE_RAMPING -#endif - - -inline void hwdef_setup() { - // enable output ports - // boost PMIC on/off - DDRC = (1 << CH1_ENABLE_PIN2); - // Opamp level and Opamp on/off - DDRB = (1 << CH1_PIN) - | (1 << CH1_ENABLE_PIN); - // aux R/G/B, button LED - DDRA = (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // PWM for both channels - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // WGM1[3:0]: 1,1,1,0: PWM, Fast, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) - | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) - ; - TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) - //| (1<<WGM13) | (1<<WGM12) // fast adjustable PWM (DS table 12-5) - | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) - ; - - // set PWM resolution - PWM_TOP = PWM_TOP_INIT; - - // set up interrupt for delta-sigma modulation - // (moved to hwdef.c functions so it can be enabled/disabled based on ramp level) - //DSM_INTCTRL |= DSM_OVF_bm; // interrupt once for each timer cycle - - // set up e-switch - SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch - SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt -} - - -#define LAYOUT_DEFINED - |