diff options
Diffstat (limited to 'hwdef-noctigon-m44.h')
| -rw-r--r-- | hwdef-noctigon-m44.h | 131 |
1 files changed, 55 insertions, 76 deletions
diff --git a/hwdef-noctigon-m44.h b/hwdef-noctigon-m44.h index 02b5904..f69fdd5 100644 --- a/hwdef-noctigon-m44.h +++ b/hwdef-noctigon-m44.h @@ -28,11 +28,14 @@ * ADC12 thermal sensor */ -#define HWDEF_C_FILE hwdef-noctigon-m44.c - #define ATTINY 1634 #include <avr/io.h> +#define HWDEF_C_FILE hwdef-noctigon-m44.c + +// allow using aux LEDs as extra channel modes +#include "chan-rgbaux.h" + // channel modes: // * 0. channel 1 only // * 1. channel 2 only @@ -40,32 +43,22 @@ // * 3. both channels, manual blend // * 4? both channels, manual blend, max 200% power // * 4. both channels, auto blend, reversible -#define NUM_CHANNEL_MODES 5 -#define CM_CH1 0 -#define CM_CH2 1 -#define CM_BOTH 2 -#define CM_BLEND 3 -#define CM_AUTO 4 -// TODO: Add RGB aux channel modes - -#define CHANNEL_MODES_ENABLED 0b00011111 -#define CHANNEL_HAS_ARGS 0b00011000 +#define NUM_CHANNEL_MODES (5 + NUM_RGB_AUX_CHANNEL_MODES) +enum channel_modes_e { + CM_CH1 = 0, + CM_CH2, + CM_BOTH, + CM_BLEND, + CM_AUTO, + RGB_AUX_ENUMS +}; + +// right-most bit first, modes are in fedcba9876543210 order +#define CHANNEL_MODES_ENABLED 0b0000000000011111 +#define USE_CHANNEL_MODE_ARGS // _, _, _, 128=middle CCT, 0=warm-to-cool -#define CHANNEL_MODE_ARGS 0,0,0,128,0 +#define CHANNEL_MODE_ARGS 0,0,0,128,0,RGB_AUX_CM_ARGS -#define USE_CHANNEL_MODES -#define USE_CHANNEL_MODE_ARGS -#define SET_LEVEL_MODES set_level_ch1, \ - set_level_ch2, \ - set_level_both, \ - set_level_blend, \ - set_level_auto -// gradual ticking for thermal regulation -#define GRADUAL_TICK_MODES gradual_tick_ch1, \ - gradual_tick_ch2, \ - gradual_tick_both, \ - gradual_tick_blend, \ - gradual_tick_auto // can use some of the common handlers #define USE_CALC_2CH_BLEND @@ -96,6 +89,7 @@ #define CH2_ENABLE_PORT PORTA // control port for PA0 +// e-switch #ifndef SWITCH_PIN #define SWITCH_PIN PA7 // pin 20 #define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt @@ -150,57 +144,42 @@ #define BUTTON_LED_PUE PUEA // for all "PA" pins -void set_level_ch1(uint8_t level); -void set_level_ch2(uint8_t level); -void set_level_both(uint8_t level); -void set_level_blend(uint8_t level); -void set_level_auto(uint8_t level); - -bool gradual_tick_ch1(uint8_t gt); -bool gradual_tick_ch2(uint8_t gt); -bool gradual_tick_both(uint8_t gt); -bool gradual_tick_blend(uint8_t gt); -bool gradual_tick_auto(uint8_t gt); - - -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead inline void hwdef_setup() { - // enable output ports - //DDRC = (1 << CH3_PIN); - DDRB = (1 << CH1_PIN) - | (1 << CH1_ENABLE_PIN) - ; - DDRA = (1 << CH2_PIN) - | (1 << CH2_ENABLE_PIN) - | (1 << AUXLED_R_PIN) - | (1 << AUXLED_G_PIN) - | (1 << AUXLED_B_PIN) - | (1 << BUTTON_LED_PIN) - ; - - // configure PWM - // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter - // pre-scale for timer: N = 1 - // Linear opamp PWM for both main and 2nd LEDs (10-bit) - // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) - // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) - // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) - // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) - TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) - | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) - | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) - ; - TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) - | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) - ; - - // set PWM resolution - PWM_TOP = PWM_TOP_INIT; - - // set up e-switch - SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch - SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt + // enable output ports + //DDRC = (1 << CH3_PIN); + DDRB = (1 << CH1_PIN) + | (1 << CH1_ENABLE_PIN) + ; + DDRA = (1 << CH2_PIN) + | (1 << CH2_ENABLE_PIN) + | (1 << AUXLED_R_PIN) + | (1 << AUXLED_G_PIN) + | (1 << AUXLED_B_PIN) + | (1 << BUTTON_LED_PIN) + ; + + // configure PWM + // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter + // pre-scale for timer: N = 1 + // Linear opamp PWM for both main and 2nd LEDs (10-bit) + // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5) + // CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6) + // COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4) + // COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4) + TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5) + | (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4) + | (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4) + ; + TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6) + | (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5) + ; + + // set PWM resolution + PWM_TOP = PWM_TOP_INIT; + + // set up e-switch + SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch + SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt } #define LAYOUT_DEFINED |