diff options
Diffstat (limited to 'spaghetti-monster/anduril/anduril-manual.txt')
| -rw-r--r-- | spaghetti-monster/anduril/anduril-manual.txt | 994 |
1 files changed, 0 insertions, 994 deletions
diff --git a/spaghetti-monster/anduril/anduril-manual.txt b/spaghetti-monster/anduril/anduril-manual.txt deleted file mode 100644 index 545af0f..0000000 --- a/spaghetti-monster/anduril/anduril-manual.txt +++ /dev/null @@ -1,994 +0,0 @@ -Anduril User Manual -------------------- - -Anduril is an open-source firmware for flashlights, distributed under -the terms of the GPL v3. The sources can be obtained here: - - http://tiny.cc/TKAnduril - https://bazaar.launchpad.net/~toykeeper/flashlight-firmware/trunk/files/head:/ToyKeeper/spaghetti-monster/anduril/ - - -Quick Start ------------ - -After putting a battery in the light and tightening the parts together, -the light should quickly blink once to confirm it has power and is now -operational. After that, basic usage is simple: - - - Click to turn the light on or off. - - Hold the button to change brightness. - - Release and hold again to change brightness the other way. - -That is all the user needs to know for basic use, but there are many -more modes and features available for people who want more. - -Before reading the rest of this manual, it is recommended that users -look at the Anduril UI diagram(s), which should be provided along with the -flashlight. - - -Button presses --------------- - -Button presses are abbreviated using a simple notation: - - - 1C: One click. Press and then quickly release the button. - - 1H: Hold. Press the button, but keep holding it. - - 2C: Two clicks. Press and release quickly, twice. - - 2H: Click, hold. Click two times, but hold the second press. - - 3C: Three clicks. Press and release quickly, three times. - - 3H: Click, click, hold. Click three times, but hold the final press. - -The same pattern is used with higher numbers too. For example, 10C -means ten clicks... and 10H means ten clicks but hold the final press. - - -Simple UI ---------- - -By default, the light uses a simple UI. This is useful if you lend the -light to someone else, or if you just don't want to bother with any -crazy disco modes. - -Simple UI has all the basic functions needed to work as a flashlight, -but the minimum and maximum brightness are limited by default to make it -safer, and any complex or advanced functions are blocked. - -Functions available in Simple UI include: - - - 1C: On / off - - 1H: Ramp up (or down, if button was released less than a second ago) - - 2H: If light is on : ramp down - If light is off: momentary high mode - - 2C: Double click to go to / from highest safe level - - 4C: Lockout mode. - -Some other modes and functions are available too. When the light is -off, these are the options: - - - 3C: Battery check mode. (displays voltage once, then turns off) - - 4C: Lockout mode. - - 10H: Switch to Advanced UI. - - 15C or more: Version check. - -In Lockout mode with Simple UI, there are a few functions: - - - 1H: Momentary moon - - 2H: Momentary low - - 3C: Unlock and turn off - - 4C: Unlock and turn on - - 4H: Unlock and turn on at low level - - 5C: Unlock and turn on at high level - -To change between Simple UI and Advanced UI, turn the light off and then -do one of these: - - In Simple UI: - - 10H: Go to Advanced UI. - - In Advanced UI: - - 10C: Go to Simple UI. - - 10H: Configure Simple UI. - -If you get lost, or if you want to auto-calibrate the temperature -sensor, do a factory reset. The process for this is: - - - Loosen tailcap - - Hold button - - Tighten tailcap - - Keep holding button for about 4s - -The light should flicker while getting brighter, then briefly burst to -full power. Hold until it reaches full power to do a reset, or let go -of the button early to abort. - -On some lights, like products where the tailcap method is impossible, -use 13H from Off to do a factory reset. If this is difficult, try -counting it like music to make it easier: - - 1 2 3 4 - 1 2 3 4 - 1 2 3 4 - HOLD - -Simple UI is enabled after each factory reset. - -Simple UI can be configured in several ways, but not while Simple UI is -active. So go to the Advanced UI, configure things, then go back to -Simple UI. - -Configurable options include: - - - floor level - - ceiling level - - number of steps (in stepped ramp) - - turbo style - -Other options are inherited from Advanced UI: - - - ramp style (smooth / stepped) - - smooth ramp speed - - ramp-after-moon style - - memory settings - - auto-lock settings - - aux LED settings - - voltage calibration - - thermal regulation settings - - hardware-specific "misc menu" settings - - -Advanced UI ------------ - -Most of the information below this is for the Advanced UI. Anything not -already noted above is blocked in the Simple UI. - - -Ramping / Stepped Ramping Modes -------------------------------- - -Anduril's ramping mode uses a smooth ramp or a stepped ramp, depending -on which style the user prefers. - -Each ramp has its own settings -- floor (lowest level), ceiling (highest -level), and the stepped ramp can also have a configurable number of -steps. - -Additionally, Simple UI has its own ramp settings for floor, ceiling, -and number of steps. The smooth/stepped style is inherited from the -Advanced UI's ramp. - -There are four ways to access ramping mode when the light is off: - - - 1C: Turn on at the memorized brightness. - (see below for details about what "memorized" means) - - - 1H: Turn on at the floor level. Let go after the light turns on to - stay at the floor level, or keep holding to ramp up. - - - 2C: Turn on at the ceiling level. - - - 2H: Turn on at full power, turn off when released. (momentary turbo) - (in Simple UI, this uses the ceiling level instead of turbo) - -While the light is on, a few actions are available: - - - 1C: Turn off. - - 2C: Go to or from the turbo level. - (or if it has regulated down, "bump" back up to turbo) - (turbo level / behavior is configurable) - - 1H: Change brightness (up). If the button was released less than a - second ago, or if it's already at the ceiling, it goes down instead. - - 2H: Change brightness (down). - - - 3C: Switch to the other ramp style. (smooth / stepped) - (or activate the next channel mode, when more than one is enabled) - (then use 6C instead, for smooth / stepped toggle) - - 6C: Switch to the other ramp style. (when 3C is mapped to next channel) - - - 3H: Momentary turbo (when current channel has no tint to ramp). - - 3H: Tint ramping (only when current channel has adjustable tint). - - 4H: Momentary turbo, when 3H is mapped to tint. - - - 4C: Go to lockout mode. - - - 5C: Go to momentary mode. - - 5H: Start a sunset timer. Details are below in the Sunset Timer section. - - - 7H: Ramp config menu. - - Item 1: Floor level. - - Item 2: Ceiling level. - - Item 3: - Stepped ramp: Number of steps. Can be 1 to 150. - Smooth ramp: Ramp speed. - 1 = Full speed, ~2.5s from end to end. - 2 = Half speed, ~5s from end to end. - 3 = Third speed, ~7.5s. - 4 = Quarter speed, ~10s. - - - 10C: Activate manual memory and save the current brightness. - - 10H: Ramp extras config menu. - - Item 1: Disable manual memory and go back to automatic memory. - (doesn't matter what value the user enters at the prompt) - - Item 2: Configure the manual memory timer. - Sets the timer to N minutes, where N is the number of - clicks. A value of 0 (no clicks) turns the timer off. - - Item 3: Configure whether to ramp up after "Off -> 1H". - 0: Ramp up after moon. - 1: Don't ramp up, just stay at the floor level. - - Item 4: Configure Advanced UI's turbo style: - 0: No turbo, only ceiling. - 1: Anduril 1 style. Ramp -> 2C goes to full power. - 2: Anduril 2 style. Ramp -> 2C goes to ceiling, - or goes to full power if user ramped up to ceiling first. - This value also affects momentary turbo in Ramp and Off modes. - - Item 5: Configure "smooth steps". - 0: Disable smooth steps. - 1: Enable smooth steps. - -Memory determines which brightness level the light goes to with 1 click -from off. There are three types of brightness memory to choose from: - - - Automatic: Always uses the last-ramped brightness. - (does not memorize levels accessed by a shortcut, - like turbo, 2C for ceiling, or 1H-from-off for floor) - - - Manual: Always uses the user's saved brightness. - - - Hybrid: Uses the automatic memory brightness if the light was only - off for a short time, or resets to the manual memory level if it was - off for a longer time. - The timer for this is configurable from 0 to ~140 minutes. - -Another way to think of it is: There are three styles of memory for the -last-ramped brightness level... - - - Always remember (automatic) - - Remember for N minutes (hybrid) - - Never remember (manual) - -To choose a memory style, set the configuration accordingly: - - mem type manual mem manual mem timer - -------- ---------- ---------------- - automatic off any - manual on zero - hybrid on non-zero - -If "smooth steps" is enabled, the stepped ramp uses a smooth animation -between steps, and turning the light on/off has the edges smoothed off -too. With "smooth steps" turned off, these brightness changes are -immediate. - - -Sunset Timer ------------- - -In the ramp mode or candle mode, it's possible to make the light turn -itself off after a while. - -To activate the timer, go to the brightness you want and then use a 5H -action. Keep holding the button, and the light should blink once per -second. Each blink adds 5 minutes to the timer. - -In ramp mode, it slowly dims until it's at the lowest level, then shuts -off. In candle mode, it stays at the same brightness until the final -minute, at which point it dims and dies out. - -The user can change the brightness while the timer is active. If this -happens during the final few minutes, it also "bumps" the timer up to a -minimum of 3 minutes. So if it's getting really dim and you need a -little more time, you could do a 5H to add 5 minutes, or simply ramp up -to the desired brightness. - - -Other Modes ------------ - -Anduril has several other modes too. To access these, press the button -more than 2 times when the light is off: - - - 3C: Blinky / utility modes, starting with battery check. - - 3H: Strobe modes, starting with the most recently used strobe. - - 4C: Lockout mode. - - 5C: Momentary mode. - - 6C: Tactical mode. - - 7C / 7H: Aux LED configuration. - - 9H: Misc Config menu. (only on some lights) - - 10H: Simple UI configuration menu. - - 13H: Factory reset (on some lights). - - 15C or more: Version check. - - -Lockout Mode ------------- - -Click 4 times from Off to enter Lockout mode. Or 4 times from Ramp. -This makes the light safe to carry in a pocket or a bag or anywhere else -the button might be pressed by accident. - -To exit lockout mode, click 4 times. The light should blink briefly and -then turn on at the memorized level. Or hold the final press to turn on -at the floor level instead: - - - 3C: Unlock and go to "Off" mode - - - 4C: Go to ramp mode (memorized level). - (uses manual mem level if there is one) - - - 4H: Go to ramp mode (floor level). - - - 5C: Go to ramp mode (ceiling level). - -Lockout mode also doubles as a momentary moon mode, so the user can do -quick tasks without having to unlock the light. The brightness in -lockout mode has two levels: - - - 1H: Light up at the lowest floor level. - - - 2H: Light up at the highest floor level. - (or the manual mem level, if there is one) - - - 3H: Next channel mode (if more than one is enabled). - -It is also possible to make the light lock itself automatically after -being turned off. To enable this, go to lockout mode and use a 10H -action to activate the auto-lock config menu. Release the button after -the first blink. Then at the prompt, click N times to set the auto-lock -timeout to N minutes. - - - 10H: Auto-lock config menu. Click N times to set timeout to N minutes. - A value of zero disables the auto-lock feature. - So, to turn off auto-lock, don't click at all. - -And on lights which have aux LEDs, there may be additional functions: - - - 7C / 7H: Change Lockout Mode's aux LED pattern. More details on - this below, in a separate section. - - -Blinky / Utility Modes ----------------------- - -Click 3 times from Off to access Anduril's blinky / utility modes. This -always starts at battery check and the user can proceed to other blinky -modes if Advanced UI is enabled. The sequence is: - - - Battery check. - - Temperature check (if light has a temperature sensor). - - Beacon mode. - - SOS mode (if enabled). - -In all of these modes, some basic actions are available: - - - Click: Turn off. - - 2 clicks: Next blinky mode. - -Additionally, in battery check and temperature check modes: - - - 7H: Go to the voltage config menu or thermal config menu. - -In more detail, this is what each blinky / utility mode does: - - Battery check: - - Blinks out the battery voltage per cell. Full is 4.2V, empty is - about 3.0V. The light blinks the whole-number digit first, pauses, - then blinks out the "tenths" digit. Then a longer pause, and it - repeats. - So for 4.2V, it would be "blink-blink-blink-blink .. blink-blink". - - A "zero" digit is represented by a very quick blink. - - On lights with more than one set of LEDs, pressing 3C during batt - check mode can select which set of LEDs (which channel mode) it uses - to blink out numbers. - - The voltage config menu has these settings: - - 1. Voltage correction factor. This adjusts the battery - measurement sensor, allowing the user to add or subtract up to - 0.30V in 0.05V steps. Click N times to enter a value: - - 1C: -0.30V - 2C: -0.25V - 3C: -0.20V - 4C: -0.15V - 5C: -0.10V - 6C: -0.05V - 7C: default, 0V - 8C: +0.05V - 9C: +0.10V - 10C: +0.15V - 11C: +0.20V - 12C: +0.25V - 13C: +0.30V - - 2. Post-off voltage display timeout. (only on lights with RGB aux) - This setting determines how many seconds the RGB aux LEDs - display the voltage color after the torch goes to sleep. Click - once per desired second, or zero times to turn this function - off. - - Temperature check: - - Blinks out the current temperature in degrees C. This number should - be pretty close to what a real thermometer says. If not, it would - be a good idea to enter the thermal config menu and calibrate the - sensor. Or let the light settle to room temperature, then use - factory reset to auto-calibrate the sensor. - - The thermal config menu has two settings: - - - Current temperature. Click once per degree C to calibrate the - sensor. For example, if the ambient temperature is 21 C, then - click 21 times. - - - Temperature limit. This sets the maximum temperature the light - can reach before it will start doing thermal regulation to keep - itself from overheating. Click once per degree C above 30. For - example, to set the limit to 50 C, click 20 times. The default is - 45 C, and the highest value it will allow is 70 C. - - Beacon mode: - - Blinks at a slow speed. The light stays on for 100ms, and then - stays off until the next blink. The brightness and the number of - seconds between pulses are configurable: - - - Brightness is the user's memorized ramp level, so set this in - ramping mode before activating beacon mode. Follows the same - memory rules as ramping -- automatic, manual, or hybrid. - - - Speed is configured by holding the button. The light should - blink once per second while holding the button. Release it - after the desired amount of time has passed, to set a new beacon - speed. - For example, to do a 10-second alpine beacon, hold the button - for 10 seconds. - - SOS mode: - - Blinks out a distress signal. Three short, three long, three short. - Repeats until light is turned off or until battery is low. - - The memorized ramp level determines the brightness of SOS Mode. - - -Strobe / Mood Modes -------------------- - -Anduril includes a few extra modes for a variety of purposes: - - - Candle mode - - Bike flasher - - Party strobe - - Tactical strobe - - Lightning storm mode - -Click 3 times from Off to access these, but hold the third click for a -moment. Click, click, hold. The last-used strobe mode is remembered, -so it will return to whichever one you used last. - -In all of these modes, a few actions are available: - - - 1C: Turn off. - - 2C: Next strobe / mood mode. - - 1H: Increase brightness, or strobe faster. (except lightning) - - 2H: Decrease brightness, or strobe slower. (except lightning) - - 4C: Previous strobe / mood mode. - - 5C: Go to momentary mode, for a momentary strobe. - (this is useful for light painting) - -Additionally, candle mode has one more action: - - - 5H: Activate Sunset Timer, and/or add 5 minutes to the timer. - -In more detail, here is what each mode does: - - - Candle mode - - Brightness changes randomly in a pattern resembling a candle flame. - If a timer is set, it will run until the timer expires, then get - dimmer for one minute, then sputter and turn itself off. Without a - timer, candle mode runs until the user turns it off. Brightness is - configurable. - - - Bike flasher - - Runs at a medium level, but stutters to a brighter level once per - second. Designed to be more visible than a normal ramping mode, but - otherwise works mostly the same. Brightness is configurable. - - - Party strobe - - Motion-freezing strobe light. Can be used to freeze spinning fans - and falling water. Speed is configurable. - - - Tactical strobe - - Disorienting strobe light. Can be used to irritate people. Speed - is configurable, and the duty cycle is always 33%. - - Be careful about heat in this mode, if using it for a long time. - - - Police strobe (on some lights) - - 2-color police style strobe. Only works on lights with 2 or more - colors. - - - Lightning storm mode - - Flashes at random brightness and random speed to simulate lightning - strikes during a busy lightning storm. Do not look directly at the - flashlight when this mode is running, because it may suddenly go to - full power without warning. - - -Momentary Mode --------------- - -Click 5 times from Off to enter Momentary mode. Or 5 times from Ramp, -or 5 times from a strobe mode. - -This locks the flashlight into a single-mode interface where the LEDs -are only on when the button is held down. It is intended for Morse -code, light painting, and other tasks where the light should be on only -for a short time and probably in a pattern. - -Momentary mode does either a steady brightness level or a strobe, -depending on which was active before going to momentary mode. To select -which one, go to the mode you want to use, adjust the brightness and -speed and other settings, then click 5 times to enter momentary mode. - -In steady mode, brightness is the memorized ramp level, so adjust that -in Ramp Mode before entering momentary mode. - -In momentary strobe mode, the settings are copied from the last-used -strobe mode, such as party strobe, tactical strobe, or lightning. - -To exit this mode, physically disconnect power by unscrewing the tailcap -or battery tube. - - -Tactical Mode --------------- - -Click 6 times from Off to enter Tactical Mode, or 6 times in Tactical -Mode to exit and go back to "Off". - -Tactical Mode provides instant momentary access to high, low, and -strobe, but each of these is configurable. The inputs are: - - - 1H: High - - 2H: Low - - 3H: Strobe - -Each of these only lasts as long as you hold the button. - -Other commands in Tactical Mode are: - - - 6C: exit (go back to Off Mode) - - 7H: Tactical Mode config menu - - 1st blink: configure tactical slot 1 - - 2nd blink: configure tactical slot 2 - - 3rd blink: configure tactical slot 3 - -To change what is in a tactical slot, press 7H, then release the button -after the 1st, 2nd, or 3rd blink. Then enter a number. Each click adds -1, and each hold adds 10. The number can be: - - - 1 to 150: set the brightness level - - 0: last-used strobe mode - - 151+: go directly to a specific strobe mode - 151 = party strobe - 152 = tactical strobe - 153+ = other strobes, in the same order they're in in the "Off -> 3H" - strobe group - -This assumes the light has a ramp 150 levels long. Strobe modes start -at the ramp size plus 1, so it may be different if a light has a -different ramp size. - - -Configuration Menus -------------------- - -Every config menu has the same interface. It has one or more options -the user can configure, and it will go through them in order. For each -menu item, the light follows the same pattern: - - - Blink once, then go to a lower brightness. The user can keep - holding the button to skip this menu item, or release the button to - dive in and enter a new value. - - - If the user released the button: - - - Stutter or "buzz" quickly between two brightness levels for a few - seconds. This indicates that the user can click one or more times - to enter a number. It will keep buzzing until the user stops - clicking, so there is no need to hurry. - - The actions here are: - - click: add 1 - - hold: add 10 (only in versions 2021-09 or later) - - wait: exit - -After entering a number, or after skipping every menu item, it waits -until the button is released then exits the menu. It should return to -whatever mode the light was in before entering the config menu. - - -Ramp Config Menu ----------------- - -While the light is on in a ramping mode, click 7 times (but hold the -final click) to access the config menu for the current ramp. - -Or, to access the ramp config for Simple UI, make sure the Simple UI is -not active, then do a 10H action from Off. - -For smooth ramping mode, there are three menu options: - - 1. Floor. (default = 1/150) - 2. Ceiling. (default = 120/150) - 3. Ramp speed. (default = 1, fastest speed) - -For the stepped ramping mode, there are three menu options: - - 1. Floor. (default = 20/150) - 2. Ceiling. (default = 120/150) - 3. Number of steps. (default = 7) - -For the Simple UI mode, there are four menu options. The first three -are the same as stepped ramping mode. - - 1. Floor. (default = 20/150) - 2. Ceiling. (default = 120/150) - 3. Number of steps. (default = 5) - 4. Turbo style. (default = 0, no turbo) - -Default values are different for each model of flashlight. The numbers -above are only examples. - -To configure the floor level, click the button equal to the number of -ramp levels (out of 150) at which the floor should be. To set the -lowest possible level, click once. - -To configure the ceiling level, each click goes one level lower. So 1 -click sets the highest possible level, 2 clicks is the 2nd-highest, 3 -clicks is the 3rd-highest level, etc. To set the default of 120/150, -click 31 times. - -When configuring the number of steps, the value can be anything from 1 -to 150. A value of 1 is a special case. It places the step halfway -between the floor and ceiling levels. - - -Version Check Mode ------------------- - -This allows people to see which version of the firmware is installed on -their light. The format for this is (usually) 12 digits -- a model -number and a date. BBPP.YYYY-MM-DD - - - BB: Brand ID - - PP: Product ID - - YYYY: Year - - MM: Month - - DD: Day - -Versions before 2023-05-30 used YYYYMMDDBBPP format. -Anduril 1 used only YYYYMMDD format, or none at all. - -The date is when the firmware was compiled. If the vendor did not set -this value, it defaults to 1969-07-20, the date of first human contact -with the moon. However, it might not be a date at all; some vendors may -specify a completely different type of value here. - -The brand/product values are also known as the model number. These are -hard-coded in the source code for each light's build target, and can be -looked up in the "MODELS" file or by using the "make models" command. - - -Protection Features -------------------- - -Anduril includes low voltage protection (LVP) and thermal regulation. - -LVP makes the light step down to a lower level when the battery is low, -and if the light is already at the lowest level, it shuts itself off. -This activates at 2.8V. LVP adjustments happen suddenly, in large -steps. - -Thermal regulation attempts to keep the light from overheating, and -otherwise adjusts output to stay as close as possible to the -user-configured temperature limit. Thermal adjustments happen -gradually, in steps so small they are difficult for humans to perceive. - - -Aux LEDs / Button LEDs ----------------------- - -Some lights have aux LEDs or button LEDs. These can be configured to do -different things while the main emitters are off. There is one aux LED -mode for the regular "off" mode, and another aux LED mode for "lockout" -mode. This allows the user to see at a glance whether the light is -locked. - -Aux LED modes typically include: - - - Off - - Low - - High - - Blinking - -To configure the aux LEDs, go to the mode you want to configure and then -click the button 7 times. This should change the aux LEDs to the next -mode supported on this light. - - - 7C: Next aux LED mode. - -If the aux LEDs can change color, there are additional actions to change -the color. It is the same as above, but hold the button on the last -click and then let go when the desired color is reached. - - - 7H: Next aux LED color. - -On most lights, the colors follow this sequence: - - - Red - - Yellow (Red+Green) - - Green - - Cyan (Green+Blue) - - Blue - - Purple (Blue+Red) - - White (Red+Green+Blue) - - Disco (fast random colors) - - Rainbow (cycles through all colors in order) - - Voltage (uses color to display battery charge) - -In voltage mode, the colors follow the same sequence, in the same order -as a rainbow... with red indicating a low battery and purple indicating -a full battery. - -For lights with a button LED, the button LED typically stays on while -the main emitters are on. Its brightness level is set in a way which -mirrors the main LED -- off, low, or high. - -For lights with a RGB button LED, the button LED indicates battery -charge during use in the same manner as the aux LED voltage mode. - -For lights with front-facing aux LEDs, the aux LEDs typically stay off -when the main emitters are on, and when the light is otherwise awake. -The aux LEDs on most lights only turn on when the light is asleep. - -When a light has a single-color aux LED and no RGB, it fast-blinks the -aux LED in "off" modes when voltage is low. - - -Misc Config Menu ----------------- - -Some models may have an extra config menu for settings which don't fit -anywhere else. This menu is located at "Off -> 9H" in the advanced UI. - -These settings are, in order: - - - Tint ramp style: (on some lights) - - 0 : smooth ramp (blend channels in any proportion) - 1 : middle tint only - 2 : extreme tints only (only one channel active at a time) - 3+: stepped ramp with 3+ steps - - - Jump Start level: (on some lights) - - Some lights are prone to starting up slowly at low levels, so they - have an option to "jump start" the engine by pulsing a higher power - level for a few milliseconds when changing from off to a low level. - This setting specifies how bright that pulse should be. - - The value can be from 1 to 150, but is usually between 20 and 50. - -These settings are hardware-specific and may not be present on all -lights. The number of settings in the Misc Config Menu depends on the -hardware model and the firmware version. - - -Channel Modes (a.k.a. Tint Ramping or Multi Channel controls) -------------------------------------------------------------- - -Some lights have more than one set of LEDs which can be adjusted to -change the beam color, shape, or other properties. These lights have -features like tint ramping and channel modes. - -On these models, there are some global button mappings which work at all -times unless they're overridden by the mode the light is in: - - - 3C: Next channel mode - - 3H: Adjust current channel mode (ramp tint, for example) - - 9H: Channel mode config menu - -Details depend on the exact type of light used. For example, if a light -has LEDs in cool white, warm white, and red... that light might have a -few channel modes: - - - White blend (adjustable CCT / tint ramping) - - Red only - - Auto-tint - -On a light like this, the user could press 3C to rotate through these -different channel modes... white, then red, then auto, then back to -white. - -Additionally, in the "white blend" mode, the user could press 3H to -manually adjust the balance between warm white and cool white. - -Finally, if the user decides they don't want all of the modes, they can -turn some off. Press 9H (while on) to start the channel mode config -menu. To disable the auto-tint mode, for example, it is the 3rd mode... -so wait for the 3rd blink, then release the button. Then at the prompt, -enter a value of 0 (wait for the prompt to time out without clicking -anything). Afterward, the auto tint mode should no longer be in the -channel mode rotation. To turn the mode back on later, do the same -thing, but enter a value of 1 (click 1 time at the prompt). - -A light can have many different channel modes, so don't be shy about -turning off any modes you don't use. It makes all the others easier to -reach. - -If you turn off channel modes until only 1 remains, the "Ramp -> 3C" -action reverts to its single-channel behavior -- switching between a -smooth or stepped brightness ramp. Additionally, when a channel mode -has nothing to adjust with 3H, the 3H action also reverts to its -single-channel behavior -- momentary turbo. - -The Misc Config Menu (Off -> 9H) may also have a setting to choose a -tint ramp style. There are a few styles available, by entering -different numbers into that config menu: - - 0: smooth ramp - 1: middle tint only - 2: extreme tints only - 3+: stepped ramp with 3+ steps - -This setting only applies to modes with channel ramping (i.e. tint -ramping), and only when that mode uses the default 3H event handler. -Custom channel modes may work differently. - - - -UI Reference Table ------------------- - -This is a table of all button mappings in Anduril, in one place: - -Mode UI Button Action ----- -- ------ ------ -Off Any 1C On (ramp mode, memorized level) -Off Any 1H On (ramp mode, floor level) -Off Any 2C On (ramp mode, ceiling level) -Off Simple 2H On (momentary ceiling level) -Off Full 2H On (momentary turbo) -Off Any 3C Battcheck mode -Off Full 3H Strobe mode (whichever was used last) -Off Any 4C Lockout mode -Off Full 5C Momentary mode -Off Full 6C Tactical mode -Off Full 7C Aux LEDs: Next pattern -Off Full 7H Aux LEDs: Next color -Off Full 9H Misc Config menu (varies per light): - ?1: tint ramp style - ?2: jump start level -Off Full 10C Enable Simple UI -Off Simple 10H Disable Simple UI -Off Full 10H Simple UI ramp config menu: - 1: floor - 2: ceiling - 3: steps - 4: turbo style -Off Any 13H Factory reset (on some lights) -Off Any 15+C Version check - -Ramp Any 1C Off -Ramp Any 1H Ramp (up, with reversing) -Ramp Any 2H Ramp (down) -Ramp Any 2C Go to/from ceiling or turbo (configurable) -Ramp Full 3C Change ramp style (smooth / stepped) -Ramp Full 6C (same as above, but on multi-channel lights) -Ramp Full 3H Momentary turbo (when no tint ramping) -Ramp Full 4H Momentary turbo (on multi channel lights) -Ramp Any 4C Lockout mode -Ramp Full 5C Momentary mode -Ramp Full 5H Sunset timer on, and add 5 minutes -Ramp Full 7H Ramp config menu: (for current ramp) - 1: floor - 2: ceiling - 3: speed / steps -Ramp Full 10C Turn on manual memory and save current brightness -Ramp Full 10H Ramp Extras config menu: - 1: switch to automatic mem, not manual mem - 2: set manual mem timeout - 3: ramp after moon or not - 4: advanced UI turbo style - 5: smooth steps - -Multi-channel lights only: -Any Any 3C Next channel mode (i.e. next color mode) -Any Any 3H Tint ramp (if this mode can) -Any Full 9H Channel mode enable/disable menu: - N: click (or not) to enable (disable) mode N - -Lockout Any 1C/1H Momentary moon (lowest floor) -Lockout Any 2C/2H Momentary moon (highest floor, or manual mem level) -Lockout Any 3C Unlock (go to "Off" mode) -Lockout Any 3H Next channel mode (if more than one enabled) -Lockout Any 4C On (ramp mode, memorized level) -Lockout Any 4H On (ramp mode, floor level) -Lockout Any 5C On (ramp mode, ceiling level) -Lockout Full 7C Aux LEDs: Next pattern -Lockout Full 7H Aux LEDs: Next color -Lockout Full 10H Auto-lock config menu: - 1: set timeout in minutes (0 = no auto-lock) - -Strobe (any) Full 1C Off -Strobe (any) Full 2C Next strobe mode -Strobe (any) Full 3C Next channel mode (saved per strobe mode) -Strobe (any) Full 4C Prev strobe mode -Strobe (any) Full 5C Momentary mode (using current strobe) - -Party strobe Full 1H/2H Faster / slower -Tactical strobe Full 1H/2H Faster / slower -Police strobe - - None (brightness is Ramp Mode's last-used level) -Lightning Full 1H Interrupt current flash or start new one -Candle Full 1H/2H Brighter / dimmer -Candle Full 5H Sunset timer on, add 5 minutes -Biking Full 1H/2H Brighter / dimmer - -Batt check Any 1C Off -Batt check Full 2C Next blinky mode (Temp check, Beacon, SOS) -Batt check Full 3C Next channel mode (for number blinks only) -Batt check Full 7H Voltage config menu - 1: voltage correction factor - ... - 5: -0.10V - 6: -0.05V - 7: no correction - 8: +0.05V - 9: +0.10V - ... - 2: post-off voltage display seconds - -Temp check Full 1C Off -Temp check Full 2C Next blinky mode (Beacon, SOS, Batt check) -Temp check Full 7H Thermal config menu - 1: set current temperature - 2: set temperature limit - -Beacon Full 1C Off -Beacon Full 1H Configure beacon timing -Beacon Full 2C Next blinky mode (SOS, Batt check, Temp check) - -SOS Full 1C Off -SOS Full 2C Next blinky mode (Batt check, Temp check, Beacon) - -Momentary Full Any On (until button is released) -Momentary Full Disconnect power Exit Momentary mode - -Tactical Full 1H High (tactical slot 1) -Tactical Full 2H Low (tactical slot 2) -Tactical Full 3H Strobe (tactical slot 3) -Tactical Full 6C Exit (go back to Off Mode) -Tactical Full 7H Tactical Mode config menu: - 1: tactical slot 1 - 2: tactical slot 2 - 3: tactical slot 3 - -Config menus Full Hold Skip current item with no changes -Config menus Full Release Configure current item - (goes to Number Entry menu) - -Number entry Full Click Add 1 to value for current item -Number entry Full Hold Add 10 to value for current item - |