1 files changed, 0 insertions, 112 deletions
diff --git a/spaghetti-monster/fsm-adc.h b/spaghetti-monster/fsm-adc.h
deleted file mode 100644
index 1bb67ed..0000000
--- a/spaghetti-monster/fsm-adc.h
+++ /dev/null
@@ -1,112 +0,0 @@
-// fsm-adc.h: ADC (voltage, temperature) functions for SpaghettiMonster.
-// Copyright (C) 2017-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-
-#pragma once
-
-#if defined(USE_LVP) || defined(USE_THERMAL_REGULATION)
-// use raw value instead of lowpassed value for the next N measurements
-// (2 = 1 for voltage + 1 for temperature)
-volatile uint8_t adc_reset = 2;
-#endif
-
-#ifdef USE_LVP
-// default 5 seconds between low-voltage warning events
-#ifndef VOLTAGE_WARNING_SECONDS
-#define VOLTAGE_WARNING_SECONDS 5
-#endif
-// low-battery threshold in volts * 10
-#ifndef VOLTAGE_LOW
-#define VOLTAGE_LOW 29
-#endif
-// battery is low but not critical
-#ifndef VOLTAGE_RED
-#define VOLTAGE_RED 33
-#endif
-// MCU sees voltage 0.X volts lower than actual, add X/2 to readings
-#ifndef VOLTAGE_FUDGE_FACTOR
-#ifdef USE_VOLTAGE_DIVIDER
-#define VOLTAGE_FUDGE_FACTOR 0
-#else
-#define VOLTAGE_FUDGE_FACTOR 5
-#endif
-#endif
-
-#ifdef TICK_DURING_STANDBY
-volatile uint8_t adc_active_now = 0;  // sleep LVP needs a different sleep mode
-#endif
-volatile uint8_t irq_adc = 0;  // ADC interrupt happened?
-uint8_t adc_sample_count = 0;  // skip the first sample; it's junk
-uint8_t adc_channel = 0;  // 0=voltage, 1=temperature
-uint16_t adc_raw[2];  // last ADC measurements (0=voltage, 1=temperature)
-uint16_t adc_smooth[2];  // lowpassed ADC measurements (0=voltage, 1=temperature)
-// ADC code is split into two parts:
-// - ISR: runs immediately at each interrupt, does the bare minimum because time is critical here
-// - deferred: the bulk of the logic runs later when time isn't so critical
-uint8_t adc_deferred_enable = 0;  // stop waiting and run the deferred code
-void adc_deferred();  // do the actual ADC-related calculations
-
-static inline void ADC_voltage_handler();
-uint8_t voltage = 0;
-#ifdef USE_VOLTAGE_CORRECTION
-    #ifdef USE_CFG
-        #define VOLT_CORR cfg.voltage_correction
-    #else
-        // same 0.05V units as fudge factor,
-        // but 7 is neutral, and the expected range is from 1 to 13
-        uint8_t voltage_correction = 7;
-        #define VOLT_CORR voltage_correction
-    #endif
-#endif
-#ifdef USE_LVP
-void low_voltage();
-#endif
-
-#ifdef USE_BATTCHECK
-void battcheck();
-#ifdef BATTCHECK_VpT
-#define USE_BLINK_NUM
-#endif
-#if defined(BATTCHECK_8bars) || defined(BATTCHECK_6bars) || defined(BATTCHECK_4bars)
-#define USE_BLINK_DIGIT
-#endif
-#endif
-#endif  // ifdef USE_LVP
-
-
-#ifdef USE_THERMAL_REGULATION
-// try to keep temperature below 45 C
-#ifndef DEFAULT_THERM_CEIL
-#define DEFAULT_THERM_CEIL 45
-#endif
-// don't allow user to set ceiling above 70 C
-#ifndef MAX_THERM_CEIL
-#define MAX_THERM_CEIL 70
-#endif
-// Local per-MCU calibration value
-#ifndef THERM_CAL_OFFSET
-#define THERM_CAL_OFFSET 0
-#endif
-// temperature now, in C (ish)
-int16_t temperature;
-#ifdef USE_CFG
-    #define TH_CEIL cfg.therm_ceil
-    #define TH_CAL cfg.therm_cal_offset
-#else
-    #define TH_CEIL therm_ceil
-    #define TH_CAL therm_cal_offset
-    uint8_t therm_ceil = DEFAULT_THERM_CEIL;
-    int8_t therm_cal_offset = 0;
-#endif
-static inline void ADC_temperature_handler();
-#endif  // ifdef USE_THERMAL_REGULATION
-
-
-inline void ADC_on();
-inline void ADC_off();
-inline void ADC_start_measurement();
-
-#ifdef TICK_DURING_STANDBY
-inline void adc_sleep_mode();
-#endif
-