diff options
Diffstat (limited to 'spaghetti-monster')
| -rw-r--r-- | spaghetti-monster/anduril/anduril.c | 2 | ||||
| -rw-r--r-- | spaghetti-monster/anduril/anduril.txt | 57 |
2 files changed, 32 insertions, 27 deletions
diff --git a/spaghetti-monster/anduril/anduril.c b/spaghetti-monster/anduril/anduril.c index 6d9d78e..ed4cb6d 100644 --- a/spaghetti-monster/anduril/anduril.c +++ b/spaghetti-monster/anduril/anduril.c @@ -1795,6 +1795,8 @@ void save_config_wl() { void low_voltage() { StatePtr state = current_state; + // TODO: turn off aux LED(s) when power is really low + if (0) {} // placeholder #ifdef USE_STROBE_STATE diff --git a/spaghetti-monster/anduril/anduril.txt b/spaghetti-monster/anduril/anduril.txt index f0f0b4d..3e0328c 100644 --- a/spaghetti-monster/anduril/anduril.txt +++ b/spaghetti-monster/anduril/anduril.txt @@ -21,7 +21,7 @@ From off: * 7 clicks: Change aux LED mode used in "off" mode. (the modes are usually off/low/high/blinking) -In steady mode: +In steady / ramping mode: * 1 click: off * Hold: ramp up * Click, hold: ramp down @@ -30,19 +30,17 @@ In steady mode: * 4 clicks: configure current ramp Smooth ramp config mode: - - Setting 1: memory on/off (not implemented yet) - * Setting 2: low end + * Setting 1: low end (click N times to set ramp floor to level N) - * Setting 3: high end + * Setting 2: high end (click N times to set ramp ceiling to level "151 - N") Discrete ramp config mode: - - Setting 1: memory on/off (not implemented yet) - * Setting 2: low end + * Setting 1: low end (click N times to set ramp floor to level N) - * Setting 3: high end + * Setting 2: high end (click N times to set ramp ceiling to level "151 - N") - * Setting 4: number of levels in discrete ramp + * Setting 3: number of levels in discrete ramp (click N times to make discrete mode have N stair-steps) (minimum 2, maximum 150) @@ -96,7 +94,6 @@ Discrete ramp config mode: * 1 click: off * 2 clicks: battcheck mode * 4 clicks: thermal config mode - - Hold: thermal calibration mode Thermal config mode: * Setting 1: calibrate sensor: @@ -106,10 +103,6 @@ Discrete ramp config mode: * Setting 2: temperature limit: At buzz, click N times to set thermal limit to roughly 30 C + N. - Thermal calibration mode: - - Hold until hot: set new ceiling value - - ... don't hold: blink out current ceiling value and exit - Lockout mode: * Hold: momentary moon * 4 clicks: exit lockout (return to regular "off" mode) @@ -127,24 +120,33 @@ Muggle mode: * Hold: Ramp up / down. * 6 clicks: Exit muggle mode. -Indicator LED support: +Indicator LED / aux LED support: + + The indicator LED (button LED), if there is one, tracks the brightness + of the main LED(s) during use. It'll be off, low, or high depending + on whether the main emitter is off, using only the first power + channel, or using a higher level. - The indicator LED, if there is one, tracks the brightness of the main - LED(s) during use. It'll be off, low, or high depending on whether - the main emitter is off, using only the first power channel, or using - a higher level. + If front-facing aux LEDs are present, they stay off while the main + light is on. They only turn on when the main emitters are off. The indicator LED can stay on when the light is in the "off" state or - lockout state. The user can configure each state to be low, high, or - off. To configure it: + "lockout" state. These modes can have different settings, to make it + easier to see which one the light is in. To configure it: + + 1. Go to the standby mode you want to configure. This is either + "off" or "lockout". + 2. In "off" mode, click 7 times to switch to the next aux LED mode. + Or in "lockout" mode, click 3 times. + 3. Repeat step 2 until the desired mode is reached. + + The available aux LED / indicator LED modes vary depending on the type + of light, but they typically have the following modes: - 1. Go to lockout mode. (4 clicks) - 2. Click 3 times, optionally holding the third press, to change the - value: - * 3 fast clicks: Change lockout mode button brightness. - * Hold the third click: Change regular "off" mode button - brightness. Let go when desired level is reached. - 3. Exit lockout mode. (4 clicks) + - Off + - Low + - High + - Blinking TODO: @@ -168,3 +170,4 @@ TODO: - candle mode: smoother adjustments? - make sunset mode timer and brightness configurable? - make beacon mode actually sleep between pulses + - add a toggle for memory? |