1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
|
// hwdef for Emisar D3AA
// Copyright (C) 2023 thefreeman, Selene ToyKeeper
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
/*
* NiMH/li-ion 9V2A boost driver based on MP3432
* with high dynamic range and DAC control + front aux RGB and button LED
*
* Pin Name Function
* 1 PA4 e-switch
* 2 PA5 BATT LVL (voltage divider)
* 3 PA6 EN: boost enable
* 4 PA7 A : button LED
* 5 PC1 -
* 6 PC2 -
* 7 PC3 -
* 8 VDDIO2 (BATT+ via solder jumper)
* 9 PD4 IN- NFET: absorb startup flash
* 10 PD5 HDR: high/low Rsense range
* 11 PD6 DAC: control voltage out
* 12 PD7
* 13 VDD VCC
* 14 GND GND
* 15 PF6 RESET
* 16 PF7 UPDI
* 17 PA0 B: aux blue
* 18 PA1
* 19 PA2 G: aux green
* 20 PA3 R: aux red
*
* BST EN enable the boost regulator and Op-Amp
* DAC sets the current, max current depends on Vset voltage divider and Rsense
* HDR FET switches between high value Rsense (low current range, pin low),
* and low value Rsense (high current range, pin high)
* IN- NFET : pull up after BST enable to eliminate startup flash, pull down otherwise
* BATT LVL : Vbat * (100.0/(330+100))
* VDDIO2 : can be connected to BATT+ with a solder jumper for VDDIO2 voltage sensing
*
*/
#define HWDEF_C hank/emisar-d3aa/hwdef.c
// allow using aux LEDs as extra channel modes
#include "fsm/chan-rgbaux.h"
// channel modes:
// * 0. main LEDs
// * 1+. aux RGB
#define NUM_CHANNEL_MODES (1 + NUM_RGB_AUX_CHANNEL_MODES)
enum CHANNEL_MODES {
CM_MAIN = 0,
RGB_AUX_ENUMS
};
#define DEFAULT_CHANNEL_MODE CM_MAIN
// right-most bit first, modes are in fedcba9876543210 order
#define CHANNEL_MODES_ENABLED 0b0000000000000001
#undef GRADUAL_ADJUST_SPEED
#define GRADUAL_ADJUST_SPEED 4
#define PWM_BITS 16 // 10-bit DAC
#define PWM_DATATYPE uint16_t
#define PWM_DATATYPE2 uint32_t // only needs 32-bit if ramp values go over 255
#define PWM1_DATATYPE uint16_t // main LED ramp
#define PWM1_GET(l) PWM_GET16(pwm1_levels, l)
#define PWM2_DATATYPE uint8_t // DAC Vref table
#define PWM2_GET(l) PWM_GET8(pwm2_levels, l)
// main LED outputs
// (DAC_LVL + DAC_VREF + Vref values are defined in arch/*.h)
// BST enable
#define BST_ENABLE_PIN PIN6_bp
#define BST_ENABLE_PORT PORTA_OUT
// HDR
// turns on HDR FET for the high current range
#define HDR_ENABLE_PIN PIN5_bp
#define HDR_ENABLE_PORT PORTD_OUT
// IN- NFET
// pull high to force output to zero to eliminate the startup flash
#define IN_NFET_DELAY_TIME 12 // (ms)
#define IN_NFET_ENABLE_PIN PIN4_bp
#define IN_NFET_ENABLE_PORT PORTD_OUT
// e-switch
#ifndef SWITCH_PIN
#define SWITCH_PIN PIN4_bp
#define SWITCH_PORT VPORTA.IN
#define SWITCH_ISC_REG PORTA.PIN4CTRL
#define SWITCH_VECT PORTA_PORT_vect
#define SWITCH_INTFLG VPORTA.INTFLAGS
#endif
#define DUAL_VOLTAGE_FLOOR (4*21) // for AA/14500 boost drivers, don't indicate low voltage if below this level
#define DUAL_VOLTAGE_LOW_LOW (4*7) // the lower voltage range's danger zone 0.7 volts (NiMH)
// comment out to use VDDIO2 instead of external voltage divider
#define USE_VOLTAGE_DIVIDER
#ifdef USE_VOLTAGE_DIVIDER
// AVR datasheet table 3.1 I/O Multiplexing, PA5 ADC0 = AIN25
#define ADMUX_VOLTAGE_DIVIDER ADC_MUXPOS_AIN25_gc
// don't use the default VDD converter
// convert BATT LVL pin readings to FSM volt units
#undef voltage_raw2cooked
uint8_t voltage_raw2cooked(uint16_t measurement);
#else
// doesn't work on this hardware in AA mode
#define USE_VOLTAGE_VDDIO2
#endif
// average drop across diode on this hardware
#ifndef VOLTAGE_FUDGE_FACTOR
#define VOLTAGE_FUDGE_FACTOR 0 // using a PFET so no appreciable drop
#endif
// this driver allows for aux LEDs under the optic
#define AUXLED_R_PIN PIN3_bp
#define AUXLED_G_PIN PIN2_bp
#define AUXLED_B_PIN PIN0_bp
#define AUXLED_RGB_PORT PORTA
// this light has three aux LED channels: R, G, B
#define USE_AUX_RGB_LEDS
// A: button LED
#ifndef BUTTON_LED_PIN
#define BUTTON_LED_PIN PIN7_bp
#define BUTTON_LED_PORT PORTA
#endif
inline void hwdef_setup() {
// TODO: for this DAC controlled-light, try to decrease the clock speed
// to reduce overall system power
mcu_clock_speed();
VPORTA.DIR = PIN0_bm // B
| PIN2_bm // G
| PIN3_bm // R
| PIN6_bm // EN
| PIN7_bm; // A
VPORTD.DIR = PIN4_bm // IN- NFET
| PIN5_bm // HDR
| PIN6_bm; // DAC
// enable pullups on the unused and input pins to reduce power
//PORTA.PIN0CTRL = PORT_PULLUPEN_bm; // B
PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
//PORTA.PIN2CTRL = PORT_PULLUPEN_bm; // G
//PORTA.PIN3CTRL = PORT_PULLUPEN_bm; // R
PORTA.PIN4CTRL = PORT_PULLUPEN_bm
| PORT_ISC_BOTHEDGES_gc; // e-switch
//PORTA.PIN5CTRL = PORT_PULLUPEN_bm; // BATT LVL
//PORTA.PIN6CTRL = PORT_PULLUPEN_bm; // EN
//PORTA.PIN7CTRL = PORT_PULLUPEN_bm; // A
//PORTC.PIN0CTRL = PORT_PULLUPEN_bm; // doesn't exist
PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
//PORTC.PIN4CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTC.PIN5CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTD.PIN0CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTD.PIN1CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTD.PIN2CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTD.PIN3CTRL = PORT_PULLUPEN_bm; // doesn't exist
//PORTD.PIN4CTRL = PORT_PULLUPEN_bm; // IN- NFET
//PORTD.PIN5CTRL = PORT_PULLUPEN_bm; // EN
// AVR datasheet 34.3.1 #2, DAC pin must have input disable set
PORTD.PIN6CTRL = PORT_ISC_INPUT_DISABLE_gc; // DAC
PORTD.PIN7CTRL = PORT_PULLUPEN_bm;
// set up the DAC
// DAC ranges from 0V to (255 * Vref) / 256
DAC_VREF = V10;
// TODO: try DAC_RUNSTDBY_bm for extra-efficient moon
DAC0.CTRLA = DAC_ENABLE_bm | DAC_OUTEN_bm;
DAC_LVL = 0; // turn off output at boot
// TODO: instead of enabling the DAC at boot, pull pin down
// to generate a zero without spending power on the DAC
// (and do this in set_level_zero() too)
}
// set fuses, these carry over to the ELF file
// we need this for enabling BOD in Active Mode from the factory.
// settings can be verified / dumped from the ELF file using this
// command: avr-objdump -d -S -j .fuse anduril.elf
FUSES = {
.WDTCFG = FUSE_WDTCFG_DEFAULT, // Watchdog Configuration
// enable BOD (continuous) in active mode
.BODCFG = ACTIVE_ENABLE_gc, // BOD Configuration
.OSCCFG = FUSE_OSCCFG_DEFAULT, // Oscillator Configuration
.SYSCFG0 = FUSE_SYSCFG0_DEFAULT, // System Configuration 0
// enable MVIO because VDDIO2 pin isn't connected
// set startup time to 64ms to allow power to stabilize
.SYSCFG1 = MVSYSCFG_DUAL_gc | SUT_64MS_gc,
.CODESIZE = FUSE_CODESIZE_DEFAULT,
.BOOTSIZE = FUSE_BOOTSIZE_DEFAULT,
};
#define LAYOUT_DEFINED
|
