1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
// Noctigon DM11 driver layout (attiny1634)
// Copyright (C) 2021-2023 Selene ToyKeeper
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
/*
* (based on Noctigon K1)
*
* Pin / Name / Function
* 1 PA6 FET PWM (direct drive) (PWM1B) (on some models)
* 2 PA5 R: red aux LED (PWM0B)
* 3 PA4 G: green aux LED
* 4 PA3 B: blue aux LED
* 5 PA2 L: button LED (on some models)
* 6 PA1 (none)
* 7 PA0 (none)
* 8 GND GND
* 9 VCC VCC
* 10 PC5 (none)
* 11 PC4 (none)
* 12 PC3 RESET
* 13 PC2 (none)
* 14 PC1 SCK
* 15 PC0 (none) PWM0A
* 16 PB3 main LED PWM (linear) (PWM1A)
* 17 PB2 MISO / (none) (PCINT10)
* 18 PB1 MOSI / battery voltage (ADC6)
* 19 PB0 Opamp power
* 20 PA7 e-switch (PCINT7)
* ADC12 thermal sensor
*
* Main LED power uses one pin to turn the Opamp on/off,
* and one pin to control Opamp power level.
* Linear brightness control uses the power level pin, with dynamic PWM.
* The on/off pin is only used to turn the main LED on and off,
* not to change brightness.
* Some models also have a direct-drive FET for turbo.
*/
#ifndef HWDEF_C
#define HWDEF_C hank/noctigon-kr4/hwdef.c
#endif
// allow using aux LEDs as extra channel modes
#include "fsm/chan-rgbaux.h"
// channel modes:
// * 0. linear + DD FET stacked
// * 1+. aux RGB
#define NUM_CHANNEL_MODES (1 + NUM_RGB_AUX_CHANNEL_MODES)
enum CHANNEL_MODES {
CM_MAIN = 0,
RGB_AUX_ENUMS
};
#define DEFAULT_CHANNEL_MODE CM_MAIN
// right-most bit first, modes are in fedcba9876543210 order
#define CHANNEL_MODES_ENABLED 0b0000000000000001
// no args
//#define USE_CHANNEL_MODE_ARGS
//#define CHANNEL_MODE_ARGS 0,0,0,0,0,0,0,0
#define PWM_CHANNELS 2 // old, remove this
#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255
#define PWM_GET PWM_GET8
#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255)
#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255
#define PWM1_DATATYPE uint8_t // linear ramp
#define PWM2_DATATYPE uint8_t // DD FET ramp
// PWM parameters of both channels are tied together because they share a counter
#define PWM_TOP ICR1 // holds the TOP value for variable-resolution PWM
#define PWM_TOP_INIT 255 // highest value used in top half of ramp
#define PWM_CNT TCNT1 // for dynamic PWM, reset phase
// linear channel
#define CH1_PIN PB3 // pin 16, Opamp reference
#define CH1_PWM OCR1A // OCR1A is the output compare register for PB3
#define CH1_ENABLE_PIN PB0 // pin 19, Opamp power
#define CH1_ENABLE_PORT PORTB // control port for PB0
// DD FET channel
#define CH2_PIN PA6 // pin 1, DD FET PWM
#define CH2_PWM OCR1B // OCR1B is the output compare register for PA6
// e-switch
#define SWITCH_PIN PA7 // pin 20
#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt
#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0]
#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
#define SWITCH_PORT PINA // PINA or PINB or PINC
#define SWITCH_PUE PUEA // pullup group A
#define SWITCH_VECT PCINT0_vect // ISR for PCINT[7:0]
#include "hank/vdivider-1634.h"
// this light has aux LEDs under the optic
#define AUXLED_R_PIN PA5 // pin 2
#define AUXLED_G_PIN PA4 // pin 3
#define AUXLED_B_PIN PA3 // pin 4
#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC
#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC
#define BUTTON_LED_PIN PA2 // pin 5
#define BUTTON_LED_PORT PORTA // for all "PA" pins
#define BUTTON_LED_DDR DDRA // for all "PA" pins
#define BUTTON_LED_PUE PUEA // for all "PA" pins
inline void hwdef_setup() {
// enable output ports
// Opamp level and Opamp on/off
DDRB = (1 << CH1_PIN)
| (1 << CH1_ENABLE_PIN);
// DD FET PWM, aux R/G/B, button LED
DDRA = (1 << CH2_PIN)
| (1 << AUXLED_R_PIN)
| (1 << AUXLED_G_PIN)
| (1 << AUXLED_B_PIN)
| (1 << BUTTON_LED_PIN)
;
// configure PWM
// Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
// pre-scale for timer: N = 1
// WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
// CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6)
// COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4)
// COM1B[1:0]: 1,0: PWM OC1B in the normal direction (DS table 12-4)
TCCR1A = (1<<WGM11) | (0<<WGM10) // adjustable PWM (TOP=ICR1) (DS table 12-5)
| (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4)
| (1<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4)
;
TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6)
| (1<<WGM13) | (0<<WGM12) // phase-correct adjustable PWM (DS table 12-5)
;
// set PWM resolution
PWM_TOP = PWM_TOP_INIT;
// set up e-switch
SWITCH_PUE = (1 << SWITCH_PIN); // pull-up for e-switch
SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt
}
#define LAYOUT_DEFINED
|
